Fanaway EVO1 - PREVAIL Installation guide

V2.1-EN (08/2019)
FANAWAY EVO1 LED
CEILING FAN WITH DIMMABLE AND COLOUR
SHIFTING LED LIGHT
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Fanaway EVO1 LED Installation Instructions
1 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Fanaway product. To ensure correct function and safety, please
read and follow all instructions carefully before assembly, installation and use of this ceiling fan. Please
keep instructions for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in
accordance with the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an

Fanaway EVO1 LED Installation Instructions
2 | P a g e
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting
the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 50kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m
above the floor in Australia.
8. This fan is suitable for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void
the warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the
ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the
suspension system shall be performed by the manufacturer, its service agent or suitably qualified
persons.
13. The light source contained in this luminaire shall only be replaced by the manufacturer or his service
agent or a similar qualified person.

Fanaway EVO1 LED Installation Instructions
3 | P a g e
BEFORE INSTALLATION
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing
before assembling. If parts are missing, return the complete product to the place of purchase for
inspection or replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any
product which appears damaged in any way. Return the complete product to the place of purchase
for inspection, repair or replacement.
•Examine all parts, you should have the following:
1 Mounting bracket x 1 10 Retraction mechanism x 1
2 Canopy screws x 4 11 Lamp base x 1
3 Canopy x 1 12 LED board x 1
4 Down rod x 1 13 Lamp shade x 1
5
Pin x 1 14 Remote x 1 set
6
Down rod housing cover x 1 15 LED driver x 1
7
Pin spring lock x 1 16 Screw for mounting bracket x 2
8 Top housing x 1
9 Blades x 4
Fig. 1

Fanaway EVO1 LED Installation Instructions
4 | P a g e
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from
the tip of the blade to the nearest objects or walls.
•Install the mounting bracket to the ceiling joist or structure that is capable of carrying a load of at least
50kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the
support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable
for the mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 15 degree angled ceiling
installation.
Fig. 2
Fig. 3

Fanaway EVO1 LED Installation Instructions
5 | P a g e
INSTALLING THE FAN
INSTALLING THE DOWN ROD
1. Remove the ball joint and dowel pin from the down rod (5) by loosening the set screw (3).
Do not discard keep these parts, they are required to reassemble later.
2. Feed the wires (2) and plug (1) through the down rod (5).
3. Insert the down rod into the down rod housing (7). Align the down rod housing hole with the down rod
hole.
Insert the pin (8) into the hole and secure with the pin spring lock (9).
4. Secure the down rod (5) and down rod housing (7) by tightening the two set screws (10) on the down
rod housing (7).
5. Install the down rod housing cover (6) over the down rod housing (7).
6. Slide the canopy (4) over the down rod (5).
7. Install the ball joint and dowel pin back onto the down rod (5) and secure by tightening the set screw
(3).
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned
on the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.5)
Insert the LED driver into the lower section of the mounting bracket then insert the remote receiver into
the top section of the mounting bracket. Fig.6
Fig. 4
Fig. 5 Fig. 6

Fanaway EVO1 LED Installation Instructions
6 | P a g e
LIGHT KIT INSTALLATION
1. Remove the lamp shade (5) from the lamp (4) base by turning it anti-clockwise.
2. Loosen and remove the screw (1) from the base bracket (3).
3. Align the two slot screws (2) with the keyhole slots of the lamp base (4).
4. Turn the lamp base counterclockwise until the slot screws are firmly at the end of the slots.
5. Secure screw 1 back to the base bracket. Tighten all three screws. Do not over-tighten.
6. Connect the female plug (1) from the fan to the male plug (1) on the LED board (2). (Fig.8)
7. Install the lamp shade (5) back onto the lamp base (4) by turning it clockwise.
Fig. 7 Fig. 8

Fanaway EVO1 LED Installation Instructions
7 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
•Ensure the motor earth wire is connected to the single earthing terminal block “B” in the diagram
below. (Fig. 9)
•After completing the electrical wiring at the mounting bracket terminal block (A);
a. Connect the remote receiver (C) power input wires and fixed wiring via the 4-port quick connector
(1).
b. Connect the LED driver (D) power input wires and remote receiver (C) power output wires via the
2-port quick connectors (3).
c. Connect the LED driver (D) PWM signal input wires and remote receiver (C) PWM signal output
wires via the 3-port quick connectors (2).
d. Connect the remote receiver (C) fan output and motor input wires via the 4-port quick connectors
(4).
e. Connect the LED driver output wires and LED light wires via the quick connectors (5).
C
D
Fig. 9

Fanaway EVO1 LED Installation Instructions
8 | P a g e
FINISHING THE INSTALLATION
•Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the
fan’s accessible metal body and lamp base back to the earth terminal at the terminal block on the
mounting bracket.
•Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy
and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using
the screws provided. (Fig. 10)
•Switch ON mains power supply to the fan. Test the fan operations or enjoy using the fan following
instructions the under “USING YOUR CEILING FAN” section of this instruction manual.
Fig. 10

Fanaway EVO1 LED Installation Instructions
9 | P a g e
USING YOUR CEILING FAN
REMOTE CONTROL
Your ceiling fan is controlled via the remote control. There are 4 buttons (HI, MED, LOW, OFF) to control
the fan speed and one button to control light on/off and dimming function. (Fig. 14)
Before operating the remote, the following must be considered.
-2 x AAA 1.5V (size) batteries are required to operate the remote control. Remove the battery cover
from the back of the remote and insert 2 x AAA batteries. Ensure the polarities are correct as shown
in the battery compartment. (Batteries included) (Fig. 11)
-The remote (transmitter) and receiver must be configured so that communication between each
other is paired up. This is achieved by setting the DIP switches on the remote (Fig. 11) and receiver
(Fig.12) are on the same settings. (Fig. 13)
NOTE: There are 4 DIP switches which can be setup to have 16 different transmitting code
combinations. This is practical when there is more than 1 remote/receiver pair operating locally or in the
same room.
NOTE: To access the receiver DIP switches, remove the DIP switch cover. (Fig. 12)
Fig. 11 Fig. 12 Fig. 13 DIP switch