Fancom LM.125 User manual

G N D
gnd

N.B.: The original, authentic version of this manual is the English version produced by Fancom B.V. or one of its
daughter companies (referred to further as Fancom). Any modifications introduced to this manual by third parties
have neither been checked nor approved by Fancom. Modifications are taken by Fancom to include translations
into languages other than English and the insertion and/or deletion of text and/or illustrations to/from the original
contents. Fancom cannot be held liable for any damages, injury, guarantee claims and other claims relating to this
type of modification, in as far as these modifications result in a content that differs from the original English
version of this manual produced by Fancom. For the latest information about product installation and operation,
please contact the customer service dept. and/or the technical service dept. of the Fancom company concerned.
In spite of the care taken when compiling this manual, if you should discover any errors, please inform Fancom
B.V. in writing. Fancom B.V., PO Box 7131, 5980 AC Panningen (the Netherlands).
Copyright © 2016 Fancom B.V.
Panningen (the Netherlands)
All rights reserved. Nothing from this manual may be copied, distributed or translated into other languages, partly
or wholly, without express prior written permission from Fancom. Fancom reserves the right to modify this manual
without notice. Fancom can give no guarantee, neither implicit nor explicit, for this manual. All risks are for the
user.
This manual has been compiled with the utmost care. If, however, you should discover an error, please inform
Fancom B.V.
Art.Nr. 35911934
GB160509

Gnd
i
g
1. General introduction .................................................................................................................................. 1
1.1 Fancom helpdesk ........................................................................................................................... 1
1.2 How to use this manual .................................................................................................................. 1
1.3 Safety instructions and warnings.................................................................................................... 1
2. Installing the LM.125 / .250 ........................................................................................................................ 2
2.1 Mount the LM.125 / .250................................................................................................................. 2
2.2 Mount the cable reel....................................................................................................................... 4
2.3 Mount the steel cable on the cable reel.......................................................................................... 4
2.4 Mount the CE protection cover on the cable reel............................................................................ 5
2.5 Mount the belt drum and belt.......................................................................................................... 6
2.6 Mount the CE protection cover on the belt drum ............................................................................ 6
2.7 Mount the pipe / chain coupling...................................................................................................... 7
2.8 Set the stroke length....................................................................................................................... 7
2.9 Connect the LM.125 / .250 ........................................................................................................... 10
2.10 Test the LM.125 / .250.................................................................................................................. 10
3. Using the LM.125 / .250............................................................................................................................ 11
3.1 Manual operation with battery drilling machine............................................................................. 11
3.2 Disposal / recycling....................................................................................................................... 11
4. Adjusting the LM.125 / .250...................................................................................................................... 12
4.1 Adjust limit switches ..................................................................................................................... 12
5. Extra possibilities..................................................................................................................................... 14
5.1 Reversing the direction of rotation................................................................................................ 14
6. Technical specifications .......................................................................................................................... 15
7. Appendix: connection diagrams............................................................................................................. 17
7.1 Actuator position feedback ........................................................................................................... 17
7.2 Connection LM 1~ Phase ............................................................................................................. 17
7.3 Control connection LM 3~ Phase Y.............................................................................................. 17
7.4 Motor connection LM 3~ phase Y................................................................................................. 18
7.5 Control connection LM 3~ Phase Δ............................................................................................... 18
7.6 Motor connection LM 3~ Phase Δ................................................................................................. 19
8. EG declaration of conformity .................................................................................................................. 20

Gnd
1
g
This manual has been compiled with the utmost care. If, however, you should discover an error, please inform
Fancom B.V..
For any questions and support, please contact the local Fancom Sales & Service Center.
The following symbols are used in this manual:
Tips and suggestions.
Note providing recommendations and additional information.
Warning indicating damage to the product if you do not follow procedures carefully.
Warning indicating danger to humans or animals.
Electrical shock hazard. Danger to humans and animals.
Example of a practical application of the described functionality.
Calculation example.
Before installing and commissioning the LM.125 / .250, read the safety instructions, provisions and conditions
carefully. This paragraph contains a number of general safety instructions. The installation of the device and
remedying of any malfunctions should be performed by a certified electrical installer according to the applicable
norms. The guarantee does not apply if this product is installed in any other way than is indicated by Fancom and
if the product's motor has been opened and changes have been made to the product.
Disconnect power before installation.
Use correct wires as shown in the connection diagrams.
Make all wiring connections and check them before applying power. Incorrect connections can cause
permanent damage.
Never place the LM.125 / .250 in a place where the weather has direct influence (not in the sun, not in
places where the temperature can rise sharply etc.).
Inspect the LM.125 / .250 periodically for any damages. Notify your installation technician immediately
of any damages. A damaged LM.125 / .250 is unsafe!
Do not touch any of the LM.125 / .250 moving parts.

Gnd
2
g
Install the LM.125 / .250 and associated components as follows:
1. Mount the LM.125 / .250 (see page 2)
2. Mount the cable reel (see page 4)
3. Mount the steel cable on the cable reel (see page 4)
4. Mount the CE protection cover on the cable reel (see page 5)
5. Mount the belt drum and belt (see page 6)
6. Mount the CE protection cover on the belt drum (see page 6)
7. Mount the pipe / chain coupling (see page 7)
8. Set the stroke length (see page 7)
9. Connect the LM.125 / .250 (see page 10)
10. Test the LM.125 / .250 (see page 10)
Never place the LM.125 / .250 in a place where the weather has direct influence (not in the sun, not in
places where the temperature can rise sharply etc.).
Place the LM.125 / .250 at such a height that the manual control can be used.
Mount the actuator on a solid and safe surface.
When mounting, the corresponding LM mounting kit can be used. Otherwise, mark the drilling holes
using the drilling jig supplied with the actuator.
Seal the gland nuts after mounting to prevent the entry of moisture, dust and/or aggressive gases.
Never mount the actuator in the following position:

Gnd
3
g
Cable / pulley combination
LM-mounting kit

Gnd
4
g
Ensure that you have the steel cable on the correct side and that you have the proper direction of
rotation for coiling up the steel cable.
Ø 50 mm
1. Feed the cable through the opening.
2. Place the retainer clamp at the end of the steel cable.
3. Wind at least 2 strokes before loading the cable.

Gnd
5
g
Ø 80/106 mm
1. Feed the cable through the opening.
2. Insert the cable into the blind hole and fix using the hexagonal socket screw.
3. Wind at least 2 strokes before loading the cable.
Placement of the CE cover is mandatory if the LM.125 / .250 installed within reach (lower than 2.5 m
above the subsurface) of humans or animals.

Gnd
6
g
Placement of the CE cover is mandatory if the LM.125 / .250 is installed within reach (lower than 2.5 m
above the subsurface) of humans or animals.

Gnd
7
g
Combination overview
The stroke length depends on whether the worm wheel supplied has been mounted or not.
Two different stroke lengths can be set on the LM.125 / .250 (see technical specifications).
The factory setting is without the worm wheel.