FarmTek 10712 User manual

©2012 FarmTek®
All Rights Reserved. Reproduction is prohibited
without permission.
EZ-Grow 3-Level
Plant and Display Bench
STK# DIMENSIONS
103854 72-1/4” W x 39” D x 94” H
10712

DISPLAY UNITS
2Revision date: 09.04.12
YOU MUST READ THIS DOCUMENT BEFORE YOU
BEGIN TO ASSEMBLE THE DISPLAY BENCH.
Thank you for purchasing this Display Bench. When
properly assembled and maintained, this product will
provide years of reliable service. These instructions include
helpful hints and important information needed to safely
assemble and properly maintain the bench. Please read
these instructions before you begin.
If you have any questions during the assembly, contact
Customer Service for assistance.
SAFETY PRECAUTIONS
• Periodically check nuts and bolts to verify they are tight
and secure.
• Do not use the Display Bench if any part is broken or
damaged.
• Do not stand on Display Bench shelves. This Display
Bench is not a ladder.
• Always lock the brakes on all four (4) wheels when the
Display Bench is not being moved.
• Do not use on inclines; Display Bench may tip or roll
away.
• Do not hang more than six (6), 10" hanging baskets of
flowers on the purlin.
• Do not load shelves with more than 200 lbs. each.
REQUIRED TOOLS
The following list identifies the main tools needed to
assemble the bench.
• Flat Head Screwdriver
• 10mm Wrench
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the
necessary parts before you begin to assemble the bench.
1. Unpack the contents of the shipment and place where
you can easily inventory the parts.
2. If anything is missing or you have questions, consult
the Pictorial Parts List, or contact Customer Service.
NOTE: At this time, you do not need to open the plastic
bag containing smaller parts such as fasteners or
washers.

3
DISPLAY UNITS
Revision date: 09.04.12
The following graphics and photos will help you identify
the different parts.
Lower End Frames (2)
Wheels (4)
Round Head
Bolts (20) Narrow Shelves (3)
Wide Shelf (1)
Purlin Supports (2)
Purlin (1)
Upper End Frames (2)

DISPLAY UNITS
4Revision date: 09.04.12
ASSEMBLY
1. Stand one (1) lower frame upright. Slide legs of one (1)
upper frame over mounting tubes on lower frame.
2. Insert one (1) round head screw through each hole in
the legs of the frame. Position the screw heads to the
outside of the frame. Tighten screws securely.
3. Repeat steps to assemble second end frame.
4. Lay one end frame on its side. Push the brake lock
lever down to lock the brake on one (1) wheel. Turn the
wheel assembly to thread the wheel stud into the insert
in the bottom of the frame leg. Turn the wheel
assembly until it is tight against the bottom of the frame
leg. Repeat this step for the remaining three (3) wheels
.

5
DISPLAY UNITS
Revision date: 09.04.12
5. Stand both end frames up as shown.
NOTE: A helper is recommended for this step.
Set one (1) narrow shelf on both frames in the lower
rear position.
6. Insert four (4) round head screws, with their heads to
the outside of the frame, through the frame and shelf.
Tighten screws finger tight at this time.
8. Set the wide shelf on both frames in the middle
position. Insert four (4) round head screws, with their
heads to the outside of the frame, through the frame
and shelf. Tighten screws finger tight at this time.
7. Set one (1) narrow shelf on both frames in the upper
position. Insert four (4) round head screws, with their
heads to the outside of the frame, through the frame
and shelf. Tighten screws finger tight at this time.

DISPLAY UNITS
6Revision date: 09.04.12
9. Set the last narrow shelf on both frames in the lower
front position. Insert four (4) round head screws, with
their heads to the outside of the frame, through the
frame and shelf. Tighten all screws securely.
10. Press the lock button on one end of the purlin. Slide the
short leg of one (1) purlin support over the end of the
purlin.
11. Continue pushing purlin support over the purlin until
the lock button pops through the hole in the purlin
support. Repeat the step for the other purlin support.
12. With the assistance of a helper, insert the ends of the
purlin assembly into tubes on the upper frames. Orient
the purlin to the front.
CAUTION: Do not stand on Display Bench shelves.