FarmTek Growers Supply 109722 User manual

CARTS AND WAGONS
Revision date: 07.11.22
©2022
All Rights Reserved. Reproduction
is prohibited without permission. STK# Description
109722 All Purpose Dump Cart
109722
ALL PURPOSE DUMP CART
12855

Revision date: 07.11.22
CARTS AND WAGONS
2
READ THIS DOCUMENT BEFORE YOU BEGIN
Thank you for purchasing this all purpose dump
cart. When properly assembled and maintained,
this product will provide years of reliable service.
These instructions include helpful hints and
important information needed to safely assemble
and properly maintain the cart. Please read these
instructions before you begin.
SAFETY PRECAUTIONS
• Do not load your cart with more than 440
pounds.
• Do not use the tipping/dumping feature of the
all purpose dump cart with more than a 220
pound payload.
• This cart is not a toy. Do not allow children to
use the cart. Never allow riders in the cart tub.
• Do not use on inclines; cart may tip or roll
away.
• Always distribute payload evenly over the
surface of the tub.
REQUIRED TOOLS
The following list identifies the main tools needed
for assembly. Two (2) people are recommended to
assemble the cart.
• Metric and standard wrenches and/or a socket
and ratchet set
UNPACK AND IDENTIFY PARTS
The following steps will help ensure that you have
all the
necessary parts before you begin to assemble.
1. Unpack the contents of the shipment and
place where you can easily inventory the
parts. Compare the shipped parts with those
shown at the bottom of each page of these
instructions.
2. If anything is missing or you have questions,
contact customer service.
• Inflate the tires to the proper level as indicated
on the tires. Inflate the tires with air only. Never
use a flammable gas to inflate the tires.
• Do not use the cart if any part is broken or
damaged.
• Always replace missing or broken parts
immediately.
• Never stand on or in the cart.
• Do not load any items on the top edges of the
plastic tub.
• Never attach this all purpose dump cart to or
pull it with a lawn tractor or other motorized
vehicle. It is not designed for road use.
CARE AND MAINTENANCE
• Periodically check fasteners to make sure they
are in place and tight.
• Clean the cart using water and mild soap.
Rinse with water sprayed from a garden hose.
(Tip the tub to allow the water to drain out after
washing.)
• Check the tire pressure and adjust to
recommended pressure if needed. Check load
rating.
• Lubricate the steering linkage with a light-
weight oil if needed. Slightly loosen mounting
bolts as needed if steering is too stiff. THE
THREADS OF THE SHOULDER BOLTS MUST
REMAIN WITHIN THE LOCKING COLLAR
OF THE LOCKNUTS. DO NOT LOOSEN THE
BOLTS TOO MUCH. DOING SO WILL CAUSE
EXCESS PLAY IN THE FRONT AXLE JOINTS.

Revision date: 07.11.22
CARTS AND WAGONS
3
PROVIDED PARTS
Rear axle Handle Bolt, Nut, and
Washer
Nuts, Bolts, and
Washers
Coupler
Handle
Wagon Tub
Wheel
Washers
Wheel Nuts
Wheels
Pre-Assembled Frame
Hitch
Rear Brace

4Revision date: 07.11.22
CARTS AND WAGONS
Parts List and Tools Required
1ATTACH PRE-ASSEMBLED FRAME TO TUB
STEP 1: Turn tub upside down and position on a
flat surface.
STEP 2: Fit the pre-assemble frame onto the bottom
of the tub.
STEP 3: Slide the axle into the whole in the back of
the pre-assembled frame. The axle is flattened on
one side to match the flat part in the frame.
Socket and
Ratchet Set
5/16" (M8) Washers (4)
Short Round Head Bolts (4)
5/16" (M8) Locknuts (4)
Phillips Screwdriver
Pre-Assembled Frame
Axle
Rear Braces (2)

Revision date: 07.11.22
CARTS AND WAGONS
5
1ATTACH PRE-ASSEMBLED FRAME TO TUB (continued)
STEP 4: Slide angled rear axle braces onto the
axle.
STEP 6: Insert the round head bolts up through the
mounting holes.
STEP 5: Line the holes in the braces with the holes
in the bottom of the tub.
STEP 7: Add the washers and locknuts. STEP 8: Tighten the locknuts. STEP 9: Repeat steps 6-8 for remaining bolts.

6Revision date: 07.11.22
CARTS AND WAGONS
Parts List and Tools Required
2ATTACH LATCH
Socket and
Ratchet Set
Phillips Screwdriver
Short Round Head Bolts (4)
5/16" (M8) Locknuts (4)
5/16" (M8) Washers (4) Hitch (1)
STEP 1: Line the hitch up to the holes on
the front of the tub. Make sure the hooks
are grabbing the bar on the pre-assembled
frame.
STEP 2: Insert the round head bolts
through the mounting holes.
STEP 3: Add the washers and locknuts.
STEP 4: Tighten the locknuts. STEP 5: Repeat steps 2-4 for remaining bolts.

Revision date: 07.11.22
CARTS AND WAGONS
Parts List and Tools Required
7
3INSTALL WHEELS
STEP 1: Slide a wheel on the axle.
Ensure the valve stem is to the outside.
STEP 2: Add a wheel washer and locknut. STEP 3: Tighten locknut until snug. Turn
the wheel to make sure the wheel still
turns freely.
STEP 4: Repeat steps 1-3 for the
remaining wheels.
Socket and
Ratchet Set
Wheel
Washers (4)
Wheel
Nuts (4) Wheels (4)

8Revision date: 07.11.22
CARTS AND WAGONS
Parts List and Tools Required
STEP 1: Determine the desired handle
orientation, slide coupler onto end of the
handle, and align bolt holes.
STEP 2: Insert the long hex head bolt
through the yoke, coupler, and handle
mounting holes.
STEP 3: Add the washer and locknut.
4INSTALL TUB HANDLE
Socket and
Ratchet Set
5/16" x 2 1/4" (M8)
Hex Head Bolt (1)
Washer & Locknut
(1 each)
Handle (1)
Coupler (1)
STEP 4: Tighten the nut until snug and
then back nut off 1/4 to 1/2 turn to allow
handle to move freely at the joint.
*Axle locknuts and flat washers are typically shipped from the factory attached to the front and rear axles.
Wrench

Revision date: 07.11.22
CARTS AND WAGONS
9
7TEST CART DUMPING OPERATION
STEP 1: Press latch to release tub. Carefully lift tub to dump contents. Do not
stand behind tub when dumping.
STEP 2: Lower tub and lock in place using latch. Verify that the latch jaw
locks around the frame bar to prevent unwanted dumping of the tub contents
when moving or while loading.