FarmTek 103780 User manual

CARTS AND WAGONS
1
Revision date: 06.22.11
STK# DIMENSIONS
103780 72" W x 73" D x 87" H
©2011 FarmTek®
All Rights Reserved. Reproduction
is prohibited without permission.
103780
EZ-Grow Hanging Plant Display
& Transport Rack
10712

CARTS AND WAGONS
2Revision date: 06.22.11
YOU MUST READ THIS DOCUMENT BEFORE YOU
BEGIN TO ASSEMBLE THE RACk.
Thank you for purchasing this rack. When properly
assembled and maintained, this product will provide years
of reliable service. These instructions include helpful hints
and important information needed to safely assemble and
properly maintain the rack. Please read these instructions
before you begin.
If you have any questions during the assembly, contact
Customer Service for assistance.
SAFETY PRECAUTIONS
Do not• use the rack if any part is broken or damaged.
This• rack is not a toy. Do not allow children to use or
hang on the rack.
Do not• use on inclines; rack may tip or roll away.
Always lock or block casters to secure rack in place.
Do not• overload the rack.
Position heavy plants on the bottom pipes only. For•
best results, place heavy plants near the ends of the
pipes.
Always load rack evenly and on both sides. Never•
place all plants on the same side. Load must be
balanced.
Never• climb on the rack or use it as a ladder.
CARE AND MAINTENANCE
Periodically check all fasteners to assure they are•
tight.
Clean the• rack using water and mild soap. Rinse with
water.
REQUIRED TOOLS
The following list identifies the main tools needed for
assembly. To safely assemble the rack, two (2) individuals
are needed.
Metric and standard wrenches and/or ratchet and•
socket set.
Pliers•
UNPACk AND IDENTIFY PARTS
The following steps help to ensure that you have all the
necessary parts before you begin.
Unpack the contents of the shipment and place where1.
you can easily inventory the parts.
If anything is missing or you have questions, consult2.
the Pictorial Parts List or contact Customer Service.

3
Revision date: 06.22.11
CARTS AND WAGONS
Parts List and Tools Required
To better align the rack, do not fully
tighten the bolts until the entire rack
is assembled. Position pipes so the
countersunk hole is to the outside for
bolt installation.
On a flat surface, assemble one end1.
frame as shown. Insert pipes into
each other until the spring-loaded
button snaps into place.
Using two (2) long bolts, and two (2)2.
washers, secure the #6 Pipe to the
end frame.
NOTE: In some instances, the bolts
included with the rack may all be the
same length. Proceed as instructed
and disregard the length references.
Thread a caster onto the end of each3.
#1 Pipe.
Repeat the steps to assemble the4.
remaining end frame.
1RAFTER ASSEMBLY
Socket/Wrench Set
Pliers
Long Bolts (4)
Washers (4)
Casters (4)
#3 Pipe (2)
#1 Pipe (4)
#8 Pipe (2)
#2 Pipe (2)
#6 Pipe (2)
Diagram not to scale.
Caster
Caster
#1 Pipe
#1 Pipe
#2 Pipe
#6 Pipe
#8 Pipe
#3 Pipe
Long Bolt &
Washer
Long Bolt &
Washer

4Revision date: 06.22.11
CARTS AND WAGONS
Parts List and Tools Required
With assistance, stand1.
the assembled frame
ends and attach the
five (5) #4 Pipes using
two (2) medium bolts
and two (2) washers for
each.
Repeat for the #5 Pipe2.
in the middle of the rack
to secure the #6 Pipes
together.
Tighten all connections.3.
Periodically check
connections to make
sure they are tight and
secure.
Lock casters to secure4.
rack position when
in use. Do not allow
casters to remain
unlocked when rack is
loaded.
2INSTALL CROSS PIPES
Socket/Wrench Set
Pliers
Medium Bolts (12)
Washers (12)
#5 Pipe (1)
#4 Pipe (5)
Diagram not to scale.
Medium Bolt &
Washer
#4 Pipe
#4 Pipe
#4 Pipe
#4 Pipe
#4 Pipe
#5 Pipe

CARTS AND WAGONS
5
Revision date: 06.22.11
Space below is reserved for customer notes.