FarmTek 108681 User manual

LAWN AND GARDEN
1
Revision date: 05.01.12
©2012 FarmTek®
All Rights Reserved. Reproduction
is prohibited without permission.
108681
Rolling Work Seat
STK# DIMENSIONS
108681 14” W x 31” L x 18” H
12855

LAWN AND GARDEN
2Revision date: 05.01.12
YOU MUST READ THIS DOCUMENT BEFORE YOU
BEGIN TO ASSEMBLE THE WORK SEAT.
Thank you for purchasing this work seat. When
properly assembled and maintained, this product will
provide years of reliable service. These instructions include
helpful hints and important information needed to safely
assemble and properly maintain the work seat. Please read
these instructions before you begin.
If you have any questions during the assembly, contact
customer service for assistance.
SAFETY PRECAUTIONS
Periodically check nuts and bolts to make sure they are•
tight and secure.
Do not use the work seat if any part is broken or•
damaged.
This work seat is not a toy. Do not let children use the•
work seat unsupervised.
Do not use on inclines; work seat may tip or roll away.•
Do not load your work seat with more than 300lbs.•
Do not load the tool tray with more than 5lbs.•
Do not inflate the tires more than 30psi. Inflate with•
ambient air only.
Never use a flammable gas to inflate the tires• .
REQUIRED TOOLS
The following list identifies the
main tools needed for assembly.
Flat head screwdriver•
Phillips head screwdriver•
Metric wrench or socket set (or an small, adjustable•
wrench)
Pliers•
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the
necessary parts before you begin to assembly.
Unpack the contents of the shipment and place where1.
you can easily inventory the parts.
If anything is missing or you have questions, consult2.
the Pictorial Parts List, or contact customer service.

LAWN AND GARDEN
3
Revision date: 05.01.12
10x15mm Flat Head Bolts (4)
10mm Washers (4)
10mm Nuts (4)
6x12mm Pan Head Bolts (4)
12mm Washers (4)
12mm Nuts (4)
Cotter Pins (5)
PICTORIAL PARTS LIST
The following photos will help you identify the different
parts.
Frame (1)Tool Tray (1)
Flat Plates (2) 12x32mm Flat Washers (8) Large Washer (1)
Seat (1)
Axles (2)
Wheels (4)

LAWN AND GARDEN
4Revision date: 05.01.12
ASSEMBLY INSTRUCTIONS
Turn the frame upside down and attach the tool tray1.
using the two (2) flat plates and 6x12mm pan head
bolts, washers, and nuts. Do not tighten the bolts at
this time.
NOTE: Set the seat aside on a surface that will not
scratch or damage the finish. It is installed last.
108681
Rolling Work Seat
Center the tool tray on the frame and tighten all2.
6x12mm bolts.
Slide one (1) wheel washer, one (1) wheel, and one (1)4.
additional wheel washer onto each end of the axles.
Mount wheels with the valve stem to the outside of the
work seat.
Slide the axles into the frame.3.

LAWN AND GARDEN
5
Revision date: 05.01.12
ASSEMBLY INSTRUCTIONS (continued)
Insert a cotter pin into each pre-drilled hole on the5.
axle. Using a pliers, spread the ends of the cotter pins
and wrap ends tightly around the axles to secure the
wheels.
Attach the seat to the seat post using four (4) 10x15mm7.
flat head bolts, washers, and nuts.
Thread the seat assembly onto the frame in a8.
clockwise motion until the threaded post can be seen
from under the work seat.
Secure the seat to the frame using the large washer9.
and cotter pin. Using pliers, spread the ends of the
cotter pin to secure the seat.
Seat height can be adjusted by rotating the seat
clockwise or counter-clockwise.
Place work seat frame on the wheels to attach the seat.6.
MAINTENANCE
Periodically check all connections to ensure safe1.
operation of work seat.
Periodically check air pressure in tires.2. Do not
overinflate. Ratings are found on tires.