FarmTek 110217 User manual

1
E-Z HAUL TRANSPORT AND DISPLAY RACK III
Revision date: 08.05.14
©2014 FarmTek®
All Rights Reserved. Reproduction
is prohibited without permission.
110217
EZ-Haul Transport and Display Rack III
10712
Photo may show a different but similar model. Actual color may differ.

E-Z HAUL TRANSPORT AND DISPLAY RACK III
2Revision date: 08.05.14
Description QTY
Hex-Head Bolts 16
Lock Washers 16
Flat Washers 16
Rack Supports 2
Base Frame 1
Adjustable Racks 5
Fixed Casters 2
Swivel Casters 2
READ THIS DOCUMENT BEFORE YOU BEGIN
Thank you for purchasing the EZ-Haul Transport and
Display Rack. When properly assembled and maintained,
this product will provide years of reliable service. These
instructions include helpful hints and important information
needed to safely assemble and properly maintain the rack.
Please read these instructions before you begin.
If you have any questions during the assembly, contact
customer service for assistance.
SAFETY PRECAUTIONS
• DO NOT load the assembled rack with more than
1100 lbs.
• Always place heaviest loads within the lower third of
the rack to prevent tipping.
• After assembly, periodically check fasteners to make
sure they are tight and secure.
• This transport and display rack is not a toy. Never allow
children to sit or climb on the rack.
• Always distribute payload evenly over the surface of
the racks.
REQUIRED TOOLS
The following list identifies the main
tools needed for assembly.
• Metric wrench or socket set with ratchet
UNPACK AND IDENTIFY PARTS
The following steps help to ensure that you have all the
necessary parts before you begin.
1. Unpack the contents of the shipment and place where
you can easily inventory the parts.
2. If anything is missing or you have questions during
assembly, contact customer service.
PARTS LIST

3
Revision date: 08.05.14
E-Z HAUL TRANSPORT AND DISPLAY RACK III
ATTACH CASTERS TO THE BASE FRAME
1. Place base frame upsidedown on a flat surface.
Place cardboard or similar material on the assembly
surface to protect the base finish.
2. At the hitch end of the base frame, attach the swivel
casters using four (4) bolts, four (4) lock washers,
and four (4) flat washers per caster. Install split lock
washer against bolt head.
3. Next, attach each fixed caster to the hitch post end of
the frame using four (4) bolts, four (4) lock washers,
and four (4) flat washers per caster. Install split lock
washer against bolt head.
4. After installing all casters, return to and tighten all
bolts using a customer-supplied metric wrench or
socket and ratchet.
5. With assistance, carefully turn the assembled base
frame over onto the casters.
1
Hitch
Attach swivel casters to hitch end of frame.
Hitch Post
Attach fixed casters to hitch post end of frame.
Fixed Caster
Base Frame
Swivel Caster
Photos may show a different but similar model.
Actual color may differ.

4Revision date: 08.05.14
E-Z HAUL TRANSPORT AND DISPLAY RACK III
INSTALL RACK SUPPORTS
With assistance, carefully lift each rack
support and slide the lower end into the corner
braces of the base.
NOTE: Position the support bars of each rack
support toward the inside (facing each other).
Align the rack stops with each other. See
diagram below (right).
2
Rack
Support
Corner
Brace
Rack
Stop
Rack
Stop
Rack
Support
Rack
Support
Rack Stop
Rack Support
Bars
Photos may show a different but similar model.
Actual color may differ.

5
Revision date: 08.05.14
E-Z HAUL TRANSPORT AND DISPLAY RACK III
3INSTALL DISPLAY RACKS
Slide each rack, lip edge facing up, into place
at the desired height.
Racks lock into place over the rack support
bars as shown in the photos. Verify that racks
are level and adjust as needed.
MAINTENANCE
• Periodically check fasteners to verify they
remain tight and secure.
• Lubricate casters with a light weight oil as
needed.
• Check racks to verify that wire grids
remain secure to rack frame. Repair or
replace as needed.
VIEW SHOWING RACK INSTALL
VIEW SHOWING RACK SEATED IN FRAME
Adjustable
Rack
Photos may show a different but similar model.
Actual color may differ.