FarmTek Growers Supply ClearSpan 106457 User manual

1
RAISED BED KITS
Revision date: 06.21.19
©2019
All Rights Reserved. Reproduction
is prohibited without permission.
STK# DIMENSIONS TIERS
106457 4' W x 8' L 1
106458 4' W x 16' L 1
106459 4' W x 24' L 1
106460 4' W x 8' L 2
106461 4' W x 16' L 2
106462 4' W x 24' L 2
106463 4' W x 8' L 3
106464 4' W x 16' L 3
106465 4' W x 24' L 3
ClearSpan™
Raised Bed Kits
Photo may show a different but similar model.

RAISED BED KITS
2Revision date: 06.21.19
READ THIS DOCUMENT BEFORE YOU BEGIN
Thank you for purchasing this raised bed kit. These
instructions include helpful hints and important information
needed to safely assemble and properly maintain the
raised bed. Please read these instructions before you
begin.
SAFETY PRECAUTIONS
• Wear eye protection.
• Use a portable GFCI when working with power tools
and cords. (Using battery-powered hand tools is
recommended.)
• Do not climb on the raised bed frame during or after
construction.
SITE
After choosing a location, proper preparation of the
site is essential. The following site characteristics are
recommended:
• For best results, assemble on a level site. Set the side
boards of the raised bed into the grade as needed to
keep the assembled bed level.
• Drainage: To prevent erosion, position the raised bed
away from buildings or other structures that may direct
water to drain toward and around the bed.
WARNING: For safety reasons, those who are not
familiar with recognized construction methods and
techniques must seek the help of a qualified contractor.
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the
necessary parts before you begin to assemble the raised
bed kit.
1. Unpack the contents of the box or boxes and place
them where you can easily inventory the shipment.
Refer to the Bill of Materials/Spec Sheets.
2. Verify that all parts listed on the Bill of Materials/Spec
Sheets are present. If you have questions or if parts
are missing, contact customer service.
CARE AND MAINTENANCE
Proper care and maintenance of your raised bed is
important. Check these items periodically for best results:
• Check all caps, brackets, and locking nubs to verify
that they remain intact and in place.
• Verify that all connections and fittings are secure and in
good condition. Repair or replace if necessary.
• Do not climb or stand on the bed frame at anytime.
• If the raised bed is disassembled and moved, inspect
all parts before reassembling.
• Replace broken or damaged parts immediately.
• For replacement or missing parts, call 1-800-245-9881
for assistance.
REQUIRED TOOLS
The following list identifies the main tools and items needed
to assemble the raised bed kit. Additional tools may be
needed depending on location and application.
• Saw to cut plastic lumber (for custom designs).
• Hammer or mallet, gloves, shovels, and tape measure.
• Carpenter's square and additional hand tools as
needed.
• String line and wood stakes (for beds > 16').

3
RAISED BED KITS
Revision date: 06.21.19
SQUARE THE BED
Squaring the raised bed applies to designs that have four (4) right angles (90°). For designs consisting of variable
angles, use an angle-measuring instrument (if possible) to verify that angles opposite each other are the same.
1. For raised beds up to and including 16' in length, simply use a carpenter's square to verify that each corner is 90°.
For beds longer than 16', consult Step 2.
2. With the bed in the desired position, measure diagonally from corner-to-corner and adjust bed until both distances
are equal.
NOTE: For longer beds, use a string line staked at both ends along the side of the raised bed to keep the sides
aligned and parallel.
3. Once the distances are equal, continue with the bed kit assembly.
String Line
Raised Bed

RAISED BED KITS
4Revision date: 06.21.19
After identifying the parts included with the shipment,
assemble the bed kit using the general steps below.
NOTE: The shapes of raised beds vary and depend
on overall design and preference. These instructions
describe assembling bed kits as 4' x 8', 4' x 16', or 4' x 24'
rectangles.
For custom shapes, use these instructions for basic
assembly steps and details, and adapt them to your raised-
bed design.
1. Determine and design the shape and height of
your raised bed based on the kit (or kits) that were
purchased.
2. Measure and level the site and verify that ample space
is present for your design.
3. Slide a bracket onto the end of one composite board
and align mounting holes.
4. Secure bracket to board by inserting a round locking
nub through the hole on each side of the bracket. Tap
with mallet to set in place if needed.
5. Take another bracket, flip as shown below, and attach it
to the other end of the board.
6. Repeat the above steps for each composite board.
ASSEMBLE BED KIT COMPONENTS
Swivel Bracket
Sideboard
Secure bracket
to board using
two round
locking nubs.
Attach brackets to
the ends of each
board as shown.

5
RAISED BED KITS
Revision date: 06.21.19
7. Layout and adjust your design. Align boards so brackets
interlock as shown. If applicable, square the bed kit.
Consult the Squaring the Bed instructions presented
earlier.
8. Once desired layout is achieved, boards are level, and
raised bed is square, slide stakes through the holes in the
interlocked brackets and drive into ground until tops are
level with the composite boards.
ATTENTION: If the raised bed is a multi-tiered design,
slide a second stake into the top of each installed stake
(7a). Slide a second tier of sideboards over the stakes (7b).
Repeat for additional tiers.
9. Once bed kit is assembled, insert the supplied stake caps
into the tops of the stakes until they snap in place. Tap with
a mallet if needed.
ASSEMBLING THE BED KIT COMPONENTS (CONTINUED) 5
6
7a
8Stake
Cap
7b
Ground
Level