Feig Electronic ID ANTRW.8060-A User manual

M00102-0e-ID.doc
Installation Manual
Shield antenna
ID ANTRW.8060-A
ID ANTRW.5040-A
(for ID RW24.ABC-A)
Delivery contents:
1 x ID ANTRW.8060-A or ID ANTRW.5040-A
4 x capping plugs 10mm
1 x Installation manual

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 2 of 8
1.1 Source of supply
With the long-range reader ID RW24.ABC-A, a shield antenna of the dimensions 800mm X 600mm
or 500mm X 400mm may be ordered.
These items are available at FEIG ELECTRONIC GmbH.
1.2 Connection of a shield antenna
Picture 1.2-1 shows the structure of a shield antenna in principle.
ID AT-A ID RW24-A
max.5 m
verdrillte Zuleitung
Schildantenne
1 m
Picture 1.2-1
Shield antennas are employed in identification of persons and goods. They are designed for wall
installation. The preferred orientation of a transponder for a secure identification is parallel to the
shield surface.
1.3 Field orientation of the antenna
Picture 1.3-1.b shows the field orientation of a simple shield antenna. It is the simplest and most
employed type of antenna with a range of application mostly in the access control of persons. The
dimensions of the antenna here depend on the required reader range and the environment of the
application.
b) Draufsicht mit eingezeichneten Feldliniena) Frontansicht
Picture 1.2-1

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 3 of 8
1.4 Ranges
Dependent on the environmental conditions, the following reader ranges can be obtained, if the
orientation of the transponder to the antenna is parallel and central.
ID ANTRW.8060-A transponder type range
ID DTK.A 660 mm
ID CTK.B 700 mm
ID ANTRW.5040-A transponder type range
ID DTK.A 560 mm
ID CTK.B 570 mm
1.5 Connecting the shield antenna to the ID AT-A
The connection of the shield antenna is executed via the automatic antenna tuner ID AT-A at the
terminals X2. In order to do this, lead the cable through the corresponding attachment screw.
Eventually replace the cable screw-joint for ribbon cables by a screw-joint for round cables.
Picture 1.5-1 Connecting plan of a shield antenna
1.6 Checking and debugging
If the automatic antenna tuner doesn't tune correctly, cabling errors easily can be detected by means
of an Ohm-Meter. For doing this, please observe the corresponding specifications for resistors in
chapter "Technical data" and the installation manual of the ID AT-A.

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 4 of 8
2.0 Technical data of the ID ANTRW.8060-A
=plastic frame (h x w x d) (800 x 600 x 15)mm
=average antenna dimensions (h x w) (740 x 540)mm
=material PVC-compact plastic
=colour white
=surface front side smooth
=weight
=protective system IP54
=inductivity 1120 µH ± 40µH
=resistance 13,0 Ohm ± 0,5 Ohm
=length of the supply line approx. 1 m
Picture 2-1 Drilling scheme of the ID ANTRW.8060-A

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 5 of 8
Picture 2-2 Drilling

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 6 of 8
2.1 Technical data of the ID ANTRW.5040-A
=plastic frame (h x w x d) (500 x 400 x 15) mm,
=average antenna dimensions (h x w) (440 x 340) mm
=material PVC-compact plastic
=colour white
=suface front side smooth
=weight
=protective system IP54
=inductivity 910 µH ± 40 µH
=resistance 9,4 Ohm ± 0,5 Ohm
=length of supply line approx. 1m
Picture 2.1-1 Drilling scheme of the ID ANTRW.5040-A
Picture 2.1-2 Drilling

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 7 of 8
Security- and warning instructions- please read before initiation!
=The appliance has to be used only for the purpose designed by the manufacturer.
=The installation manual has to be stored available at any time and has to be handed over to each user.
=Unauthorized changes and the use of spare parts and additional appliances which have not been sold or recommended
by the manufacturer may cause fire, electric shocks or injuries. Such measures will lead to exclusion of any liability by
the manufacturer.
=The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the appliance. The
manufacturer is not legally responsible for incorrect, unsuitable manual or automatical setting of parameters for an
appliance or the incorrect application of an appliance.
=Repairs can only be executed by the manufacturer.
=Installation-, operation- and maintenance procedures should only be carried out by qualified personnel trained for
accident prevention.
=When working with appliances with leading parts, please observe the valid security prescriptions.
=Before opening the appliance, the power supply must always be interrupted. Make sure that the appliance is without
voltage by measuring.
=CAUTION! The fading of an operation control (LED) is no indicator for an interrupted power supply or the appliance
being without voltage!
=Working with the opened appliance, please consider that leading parts near the transformer, the relays and the
connector terminal are bare.
=Works at the appliance and its installation have to be executed according to the national legal requirements and local
prescriptions.
=The user is responsible for the installation, application and connecting of the appliance according to the technical
standards of the installation country and other valid prescriptions. Dimensions of wires and cables, safety regulations,
earthing, separation, insulation control and overcurrent protection have to be considered in particular.

Identifikationssystem OBID ® Installation Manual Shield antenna
FEIG ELECTRONIC GmbH M00102-0e-ID.doc page 8 of 8
Issue: hg/25/04/00 – M00102-0e-ID.doc
© Copyright 1999 by FEIG ELECTRONIC GmbH
Transmitting and copying this document, using and communicating its contents are illegal if not allowed explicitly. Any
offence commits to paying compensation. All rights reserved for cases of granting patents or registration of design.
The information given in this manual may be changed without advance notice. After appearance of these installation manual,
all former editions will become invalid.
The information in this manual have been compiled to the best of knowledge and belief. FEIG ELECTRONIC GmbH does not
guarantee the correctness of informations in this manual. Especially, FEIG ELECTRONIC GmbH is not legally responsible for
damages caused by incorrect information of this manual.
As it is not possible to avoid faults entirely, we are indebted for receiving outside corrections at any time.