Feig Electronic OBID ID ANT.BS.100-A User manual

M61092-4e-ID.DOC
Installation Manual
ID ANT.BS.100-A
(Antenna-Kit for the ID RW24.ABC-A)
Extent of supply:
1x ID AT-A (automatic antenna tuner)
1x ID ANT.AP-B (Connecting board)
1x 5 m connecting cord for ID AT-A (LiYCY 2 x 2 x 0,5)
1x 5 m ribbon cable for antenna (26 x AWG28, grid pitch 1,27)
1x 1 m connecting cable ID AT-A to ID ANT.AP-B (2 x 1 mm², twisted)
2x ribbon cable plugs for antenna
1x assembly instruction

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 2 to 11
1. Installation:
1.1 Take note of proper succession
1. Construct and connect the antenna (ribbon cable antenna to X3 and X4, single core antenna to
X2 of ID AT-A).
2. Connect supply and signal lines with X1 at ID AT-A
3. Switch on of supply voltage and check of alignment status by means of LED.
1.2 Setting up instructions ID AT-A
Please set up the automatic antenna tuner directly at antenna. The maximum length of connection
cable should be no longer than 1 meter.
For wall-mounting transparent lid of housing should be removed. ID AT-A can be bolt together with
the underground by four drill holes.
1.3 Terminal system / Connection ID AT-A
Please connect automatic antenna tuner ID AT-A by mean of clamp X1 with the reader. Figure
1.3-1 shows as an example a connecting system for an ID RW24.ABC-A.
In case of metal-frame antenna like ID ANTRW.8060R-A please note to connect PE (separate
line) to antenna frame and bridge between GND and PAA on ID RW24.ABC-A!
If you want to connect a ribbon cable antenna to ID AT-A, the antenna should be connected to
terminal X3 and X4.
Please connect a single coiled antenna to terminal X2 of antenna tuner. Also if you are using the
connection board ID ANT.AP-B you have to use the terminal X2.
Caution:
Connection of ribbon cable antenna (X3 and X4) and single core antenna (x2) at the
same time is not possible!

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 3 to 11
X7
4
3
2
1
L
N
PE
5
4
3
2
1
Sig+
Sig-
U+
GND
PAA
ID RW24.ABC-A
X1 U+
GND
+Sig
-Sig
X1
screen not put on
ID AT-A ANT
ANT
X2
X3 X4
antenna housing
(only antenna with metal frame)
max. 5 m
Bild 1.3-1: Connection of the AT-A to reader ID RW24.ABC-A
1.4 Wiring and type of cable
It is not possible to choose length and type of cable. Connecting cable should be appropriate for
transmission of energy as well as HF signal.
Please note the following instructions
lEnclosed connecting cable, LiYCY with two double-cores should be used indoors. The re-
commended type of cables for outdoor or underground use are: telephone cable for outside
use A-2Y (L) 2Yb2Y with two double-cores and line diameter of 0,8 mm corresponding to VDE 0816
lLength of connecting cable between ID RW24.ABC-A and ID AT-A should be no longer than 5 m.
lFeed line should be at least 30 cm away from parallel, current-carrying cables.
lIf you use an underground feed-line, please use protecting tubes.
lPlease connect antenna signal and voltage supply with each one line.

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 4 to 11
1.5. Instructions for making of antenna
The maximum reading distance of reader is substantially being influenced by the construc-
tion of the antenna.
1.5.1 General Instructions:
Because of its better features, you should prefer an antenna made of ribbon cable to a coi-
led single core one.
ID AT-A is appropriate for antennas having a range of inductivity from 600 µH up to 1200 µH.
An effective size of antenna is about 50 cm x 70 cm with about 22 to 26 windings using ribbon
cable. For other but similar constructions the inductivity of the antenna should range in-between
1000 µH and 1100 µH. Metal surfaces or parts should be at least 30 cm away from antenna.
When using a relatively small antenna reading results might turn out inaccurate if situated close to
transponder. The transponder deliver accurate results when operated in a greater distance from
antenna.
1.5.2 Instructions for making of a ribbon cable antenna without connection board:
The construction set on hand makes a set up of a antenna possible in two ways: On the one hand
there are two 26-pin plug manuals on the printed circuit board which you can use to assemble the
antenna with ribbon cable enclosed. On the other hand our antenna construction set includes
another connecting board (ID ANT.AP-B) which can be connected to the ribbon cable enclosed to
set up the antenna.
This connecting-board can be connected to terminal X2 of antenna-tuner ID AT-A using the solde-
red two-core twisted cable.
To make a ribbon cable antenna by means of the two 26-PIN plug – manual of ID AT-A, please
make a ready-made ribbon cable with cable enclosed using the corresponding spring manuals.
Caution:
Please lead ends of ribbon cable through screw joint into the housing of ID AT-A before
making it ready-made and then connect it with cable.
The easiest way of doing this, is to put one cable upon the other (parallel), buckled in the middle
and lead it through the cable connection.

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 5 to 11
Figure 1.5-1
Before fixed antenna is being connected, please check inductivity between the two contacts of
clamp X1.
Both ends of the ribbon cable leading to the antenna-tuner should be parallel and we recommend
to shorten them to minimum length.
By using jumpers J1 - J4 you can choose the number of windings (according to table 1.6. 2-1) to
keep to the range of inductivity given.
Please fix only one jumper J1-J4 at the same time.
Jumper no. of
windings
J1 26
J2 22
J3 18
J4 14
Table 1.5-1

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 6 to 11
1.5.3 Instructions for making of a ribbon cable antenna with connection board:
To set up a ribbon cable antenna using connecting board ID ANT AT-A please make enclosed
ribbon cable ready-made with corresponding spring boards following Figure 1.5-2
J6
J7
X2
J3
J5
J4
J1
J2 X1
Pin 1
Pin 1
Figure 1.5-2
X1 serves to crimp the ribbon to the printed circuit board, X2 can serve as a spring- or pin-manual.
To connect connecting board and ID AT-A (X2) you can use the two-core twisted cable enclosed
to construction set. You can shorten the given length of one meter following your special require-
ments, but you should not lengthen it. Using jumper J1 to J7 you can choose the number of win-
ding in use to keep to given range of inductivity.
Caution: Fix only one jumper J1 to J7 at the same time.
Jumper No. of win-
dings
J1 26
J2 24
J3 22
J4 20
J5 18
J6 16
J7 14
Table 1.5-2
Schedule 1.5-2 shows inductivities to be expected for different sizes of antenna and numbers of
windings.

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 7 to 11
You can calculate the antennas surface by multiplication of mean length of the edge (Table 1.5-
3.). The ratio between length of edge “a” and “b” should not exceed the value of 2:1.
You can reach the number of windings 28 and 36 by using a double winded antenna loop. Please
use jumpers to choose number of windings 14 or 18 on ID AT-A as connecting board. For the ma-
ximum range of readers‘ at a given surface of antenna please choose the highest inductivity (prin-
ted in bold).
Inductivity [µH] corresponding to number of windings
surface A
[cm²] 18 Wdg. 22 Wdg. 26 Wdg. 28 Wdg.* 36 Wdg.*
800 603 909
1000 700 1059
1200 790
1400 660 875
1600 720 955
1800 778 1032
2000 626 833 1105
2200 666 886
2400 704 937
2600 740 986
2800 776 1034
3000 811 1081
3200 844 1126
3400 619 877
3600 642 910
3800 664 941
4000 685 972
4200 706 1002
4400 727 1032
4600 747 1061
4800 767 1090
5000 787 1118
Table 1.5-3

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 8 to 11
b
a
Bild 1.5-3
1.5.4 Instruction for set up a winded single core antenna:
Please note to keep the given inductivity range.
An efficient antenna size is about 50 cm x 70 cm and 21 to 25 winding using cord (type LiY 0,25
mm2). For other but similar constructions an antenna inductivity of approx. 1000µh to 1100µH
should be reached.
Connection between antenna-tuner and antenna should not exceed a maximum length of 1 meter
and has to be twisted.
Antenna winding should be as close as possible.
Antennas with an internal resistor < 15 Ωcan cause the antenna-tuner not to adjust perfectly.
Then you should increase the internal resistor of antenna up to approx. 15 Ωby a serial resistor
between antenna and antenna tuner. The resistor should layed out for a current of 300 mA. If this
is not efficient you should reduce the number of windings by one.
A = a •b

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 9 to 11
1.6 Alignment
See installation manual of the ID AT-A
LED Meaning
RUN - yellow - RUN-LED of processor, flashes in in-
tervalls of 0.5 seconds if ID AT-A
works properly.
AF - red - Adjustment error: Indicates error and
switching of capacities.
AS - green - State of adjustment. Indicates correct
adjustment.
Tabelle 1.6-1

Identifikationssystem OBID®Installation Manual ID ANT.BS.100-A
FEIG ELECTRONIC GmbH M61092-4e-ID Page 10 to 11
Safety- and warning instructions
read in any case BEFORE installation!
•The device may only be used according to the intentions of the manufacturer.
•This manual must be available for each user at any time.
•Unauthorized modifications and the usage of additional parts and devices which are not distributed or
recommended by the manufacturer can cause fire, electric shocks and injuries. These cases release the
manufacturer from his responsibility.
•The manufacturer’s guarantee conditions are valid in the version supplied with the unit at the date of
purchase. The manufacturer is not liable for system failures caused by wrong, improper manual or auto-
matical adjustment of parameters for a device nor for misuse of a device.
•Repairs can only be carried out by the manufacturer.
•Installation-, operation- and maintenance procedures should only be carried out by qualified personnel.
•Before opening the device, the power supply must always be interrupted. Make sure that the device is
without voltage by measuring. CAUTION! The fading of an operation control (LED) is
no indicator for an
interrupted power supply or the device being without voltage!
•Installation, operation and maintenance of the device have to be executed corresponding to the national
legal requirements and to all other local regulations. The user is responsible for an installation and con-
nection of the unit according to local and national regulations of his country. Dimensions of wires and
cables, safety regulations, earthing, separation, insulation control and overcurrent protection have to be
considered in particular.
•Mixed use of small and low voltage at the output of the relay is not allowed.
•In case of forcible removal of the reader, the control line for the door/gate control ( if the relay is being
used) can be short-circuited. Thus, an unauthorized access to a door or gate might be possible.