Fein KBE 35 N24 Setup guide

KBE 35 N24; Holemaker III
Repair Instructions
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 61

KBE 35 N24; Holemaker III
Contents
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 2of 61
1. Models described
2. Technical data
3. Notes and requirements
4. Tools required
5. Lubricants and auxiliary substances required
6. Removal
7. Fitting
8. Connection diagram

KBE 35 N24; Holemaker III
1. Models described
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 3of 61
These repair instructions describe how to repair the following models:
Model
Order number
KBE 35 N24
7 270 59 .. .. .
Holemaker III
7 270 59 .. .. .

KBE 35 N24; Holemaker III
2. Technical data
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 4of 61
Technical data
All the technical data can be found in the operating instructions for the model.
Test data
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides).
Lubricants
The lubricants and container sizes available from FEIN can be found on the FEIN Extranet (Customer Service →Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com

KBE 35 N24; Holemaker III
3. Notes and requirements
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 5of 61
Please note
These instructions are only intended for persons with suitable technical training. It is assumed that the reader has mechanical and
electrical training.
Only use original FEIN spare parts.
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained electrician, as improper repair can result in
serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
The relevant accident prevention regulations of the employer’s liability insurance associations are to be observed when
commissioning.
The German Equipment and Product Safety Act [ProdSG] applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed.

KBE 35 N24; Holemaker III
4. Tools required
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 6of 61
Standardwerkzeuge
Plastic hammer
Sleeve
•Ø inside 44 mm
Ø outside 55 mm
•Ø inside 39 mm
Ø outside 46 mm
•Ø inside 17 mm
Ø outside 25 mm
•Ø inside 16 mm
Ø outside 25 mm
•Ø inside 26 mm
Ø outside 42 mm
•Ø inside 7 mm
Ø outside 18 mm
•Ø inside 5 mm
Ø outside 15 mm
•Ø inside 10 mm
Ø outside 24 mm
•Ø inside 5 mm
Ø outside 16 mm
•Ø inside 7 mm
Ø outside 18 mm
•Ø inside 10 mm
Ø outside 23 mm
•Ø inside 13 mm
Ø outside 26 mm
•Ø inside 7 mm
Ø outside 13 mm
•Ø inside 26 mm
Ø outside 30 mm
Cross-head screwdriver
Slotted screwdriver
Torx screwdriver
T15; T20
Arbor press
Circlip pliers
Socket head wrench-set

KBE 35 N24; Holemaker III
4. Tools required
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 7of 61
Special tools
Drawing-off socket cap
Assembly aid
Chuck cone 26 mm
Chuck cone 24 mm
Chuck cone 19 mm

KBE 35 N24; Holemaker III
5. Lubricants and auxiliary substances required
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 8of 61
Lubricants
Grease
0 40 128 03 00 0
35 g
Getriebe

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 9of 61
Removing the container
NOTE:
Fluid may be present in the container.
Drain the container (2) before removal.
1. Remove the hose (1) from the hose socket.
2. Remove the container (2).
1
2

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 10 of 61
Removing the electronics
1. Unscrew the six screws (1).
2. Remove the holder (2).
3. Remove the cover (3).
4. Disconnect all the connectors (4).
5. Unscrew the screw (5).
6. Unscrew the screw (6).
7. Remove the cable clamping piece (7).
Tools:
- Torx T20
1
3
2
4
5
7
6
Abbildung ähnlich

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 11 of 61
Removing the electronics
1. Remove the two switches (1) and the button (2).
2. Remove the cover (3).
3. Unscrew the screw (4).
4. Disconnect all cables.
5. Remove the cover (5) with the electronics.
6. Unscrew the two screws (6) and remove the electronics.
Tools:
- Torx T20
1
2
3
6
4
5

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 12 of 61
Removing the magnetic foot
1. Unscrew the fillister head screw (1).
2. Unscrew the four screws (2) and remove the magnetic foot.
3. Unscrew the screw (3) and remove the cable.
Tools:
- Torx T20
- Socket head wrench,
5 mm
- PH2 cross-head
screwdriver
1
2
3
1

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 13 of 61
Removing the connecting cable
1. Remove the protective hose (1).
2. Remove the sealing ring (2).
3. Remove the circlip (3).
4. Pull out the connecting cable (4).
Tools:
- Circlip pliers
3
4
1
2

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 14 of 61
Removing the guide
1. Unscrew the screw (1).
2. Move the guide upwards using the spider.
3. Remove the guide.
4. Unscrew the screw (2).
5. Unscrew the flat headed screw (3).
Tools:
- Socket head wrench,
4 mm
- Slotted screwdriver
1
2
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 15 of 61
Removing the guide
1. Remove the circlip (1).
2. Pull out the spider (2).
3. Remove the bush (3) on both sides.
Tools:
- Circlip pliers
- Inner bearing puller,
18-22 mm
- Slide hammer
1
2
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 16 of 61
Removing the guide
1. Remove the disc (1).
2. Unscrew the screw (2) and remove the shaft.
3. Unscrew the three handles (3).
Tools:
- Socket head wrench,
5 mm
1
2
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 17 of 61
Removing the guide
1. Unscrew the fillister head screw (1).
2. Remove the leaf spring (2).
3. Unscrew the six set screws (3).
4. Unscrew the twelve screws (4) and remove the guide strips.
5. Remove the pressure piece (5).
Tools:
- PH2 cross-head
screwdriver
- Socket head wrenches,
2.5 mm; 3 mm
1
2
4
5
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 18 of 61
Removing the motor housing
1. Unscrew the screw (1) [both sides].
2. Remove the cover (2) [both sides].
3. Lift up the spring (3) [both sides].
4. Remove the carbon brush [both sides].
Tools:
- Torx T15
- Assembly Aid
1
2
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 19 of 61
Removing the motor housing
1. Unscrew the four screws (1).
2. Unscrew the two screws (2).
3. Remove the cover (3).
Tools:
- Torx T15
1
2
3

KBE 35 N24; Holemaker III
6. Disassembly
C-SC_CSSM
Version 1.0
2019-02-15
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 20 of 61
Removing the motor housing
1. Remove the cable (1) [both sides].
2. Unscrew the five screws (2).
3. Remove the motor housing (3).
4. Remove all components from the motor housing.
Tools:
- Torx T15
1
2
3
3