Firesense LIP-10A-TGG-LPG-BU User manual

1
PRO Series
Outdoor Patio Heater
Model # LIP-10A-TGG-LPG-BU
Item # 61159/61436
ATTACH YOUR RECEIPT HERE
Serial Number ___________ Purchase Date ______
Manufacturer: Changzhou Wellife Furnace Co., Ltd.
Questions, problems, missing parts? Before returning to your
retailer, call our customer service hotline at 1-866-985-7877,
9 a.m. –6 p.m., EST, Monday –Friday or email at
[e-mail].

2
Table of Contents………………………………….....................Page 2
Before You Begin............................................................Page 2
Safety Information.........................................................Page 3-4
Package/Hardware Contents…...…………….....................Page 5-6
Assembly.........................................................................Page 7-11
Operating Instructions……………......................................Page 11-14
Care and Maintenance……………………..............................Page 14
Troubleshooting……………………………………......................Page 15
Replacement Parts List.....................................................Page 16-17
Warranty Information…………….....................................…Page 18
BEFORE YOU BEGIN
Please read and understand this entire manual before attempting to assemble, operate or install this appliance.
If you have any questions regarding the product, please call customer service 1-866-985-7877, 9 a.m. –
6 p.m., EST, Monday –Friday.
This manual contains important information about the assembly, operation and maintenance of this patio
heater. General safety information is presented in the first few pages and is also located throughout this manual.
Keep this manual for future reference and to educate new users of this appliance. This manual should be read
in conjunction with the labeling on the appliance. Safety precautions are essential when any mechanical or
propane fueled equipment is involved. These precautions are necessary when using, storing, and servicing.
Using this appliance with the respect and caution demanded will reduce the possibilities of personal injury or
property damage. The following symbols shown below are used extensively throughout this manual. Always
heed these precautions, as they are essential when using any mechanical or propane fueled equipment.
TABLE OF CONTENTS

3
SAFETY INFORMATION

4
SAFETY INFORMATION

5
PACKAGE CONTENTS
ASSEMBLY
PART
DESCRIPTION
QTY
A
Reflector Panel
1 packed in 1
carton
B
Head Assembly
1 (packed in 1
inner ctn)
C
Tank Housing
1
D
Gas Hose
1 (attached to
Head
Assembly)
E
Regulator
1 (packed with
Head
Assembly)
F
Post
1
G
LPG Tank Strap
1
H
Post Supports
3 (packed in 1
inner ctn)
I
Base with Waterbox
1
J
Wheels
2 (packed with
Head
Assembly)
ITEM 61159 (One piece reflector)
HARDWARE CONTENTS
ASSEMBLY

6
PACKAGE CONTENTS
ASSEMBLY
ITEM 61436 (5 piece reflector)
PART
DESCRIPTION
QTY
A
Reflector Panel and
Center Cap
4 pcs panel and
1 pc center cap
(packed in 2
inner ctns)
B
Head Assembly
1 (packed in 1
inner ctn)
C
Tank Housing
1
D
Gas Hose
1 (attached to
Head
Assembly)
E
Regulator
1 (packed with
Head
Assembly)
F
Post
1
G
LPG Tank Strap
1
H
Post Supports
3 (packed in 1
inner ctn)
I
Base with Waterbox
1
J
Wheels
2 (packed with
Head
Assembly)
HARDWARE CONTENTS
ASSEMBLY

7
PREPARATION
Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package
contents list and hardware contents as listed on pages 5 and 6 of this manual. If any part is missing or damaged,
do not attempt to assemble this product. Contact customer service for replacement parts.
ESTIMATED ASSEMBLY TIME: 60 minutes
Tools Required for Assembly (NOT included):
Phillips screwdriver w/medium blade
Leak Test Solution
Adjustable wrench (2) (Note: 10mm wrench or socket should fit M6 bolt; 13mm wrench or socket should fit M8
bolt.)
NOTE: This heater has an Electronic Ignition and will require installation of 1 –AAA battery. The battery should
be installed by unscrewing the RED IGNITER BUTTON.
1. Attach Wheels (J) to Base (I). Align holes in Wheel bracket with
corresponding holes in Base, and insert 3 M6x16 (BB) bolts through holes
and finger tighten. Repeat with second wheel. Tighten with wrench once
both wheels have been attached.
Hardware Used: 6 x BB, Bolt M6x16
Waterbox assembly: For models that come with a waterbox, remove
the plastic cap (1) and fill the waterbox with water or sand. Replace plastic cap.
Slide Base (K) down over waterbox and insert bolt (2) through washer (3) and
sleeve (4). Secure beneath waterbox by tightening nut (5) onto end of washer.
You may find it easier to complete waterbox assembly prior to attaching wheels.
ASSEMBLY
1

8
2. Attach the Post Supports (H) to the Base (I). Align the holes in the
bottom of each Post Support with the hole on the Base.
Insert 1 M8x16 (AA) bolt through the hole in the support and into the
Base and hand tighten. Repeat with the other 2 Post Supports and
then tighten all bolts with a wrench.
Hardware Used: 3 x AA, Bolt M8x16
3. Attach the Post (F) to the Post Supports (H). Once you
have tightened the bolts holding the Post Supports (H) to the Base (I),
align the holes in the Post (F) with the holes on the tops
of the Post Supports (H) and insert a M6x35 (CC) bolt through a M6 (HH)
washer and then through the hole in the Post Support. Affix another
M6 (HH) washer onto the bottom of the M6x35 (CC) bolt and secure with a
M6 (DD) nut. Repeat this in the 5 remaining holes (6 holes total—2 for
each Post Support piece). Hand tighten initially then tighten with a
wrench when all bolts have been inserted.
Hardware Used: 6 x CC, Bolt M6x35
12 x HH, Washer M6
6 x DD, Nut M6
2
3
ASSEMBLY

9
4. Place Tank Housing (C) onto Base (I). Slide Tank Housing (C) over
the Post and down over the Post Supports.
Rest Tank Housing on Base.
5. Attach Head Assembly (B) to Post (F).
Note: There is a small piece of protective foam located in the
neck of the Head Assembly that MUST be removed prior to
attaching Head Assembly to the Upper Post.
Route Gas Hose (D) down into Post and align 4 small holes on
Head Assembly with 4 Small holes in Post (F).
[HINT: Control knob should be above decal on post.]
Insert 4 M6x10 (EE) bolts through 4 M6 lock washers into holes
and tighten.
Hardware Used: 4 x EE, Bolt M6x10 and Lock Washer M6
6-1. FOR ITEM 61436
Assemble Reflector Panels (A) with Reflector Center Cap. Reflector
Panels (A) come packaged in two brown boxes with two panels in each
box. Hardware for assembly is already affixed to each panel. Place two
panels side by side and remove the two cap nuts and washers that are
affixed to one panel. Insert the affixed bolts into the open holes on the
adjacent panel. Place the washer over the bolt and screw on cap nut.
Repeat these steps until all four panels are assembled. Then locate
the Reflector Center Cap. You will need to remove the cap nuts and
washers located at the top of each Reflector Panel to allow assembly
of the Center Cap on each panel. Align the holes in the Center Cap
with the bolts on each panel and affix washer and cap nut to
complete assembly.
5
4
6-1
ASSEMBLY

10
6-2. FOR ITEM 61159 AND 61436
While supporting heater, tilt the Head Assembly (B) and slide the
Reflector (A) over the 3 bolts that extend from the Head Assembly.
Use the 3 M8 Wing Nuts (EE) and 3 M8 Washers (GG) to secure the
Reflector to the Head Assembly of the heater. Once you have
tightened the Wing Nuts, return the heater to an upright position.
Hardware Used: 3 x EE, Wing Nut M8
3 x GG, Washer M8
7. Connect the hose and regulator to the LP cylinder. The LP cylinder is
sold separately. Use a standard 20 lb. propane cylinder only. Lift the
Tank Housing (C) up and rest it on the top of the assembled Post Supports (H).
Screw Regulator (E) onto Gas Hose (D). Do not cross thread. Hand tighten securely
then tighten with a wrench. Attach Regulator (E) to valve on LP cylinder and
hand tighten securely. Place LP tank onto base of heater
and secure LP Tank on base by hooking Tank Strap (G)
onto the Post Supports (H). Lower the Tank Housing.
NOTE: Use this heater only with a propane
vapor withdrawal supply system. See chapter 5 of
the standard for storage and handling of liquefied
petroleum gas, ANSI/NFPA 58. Your local library or
fire department should have this book.
6-2
7
ASSEMBLY