First Degree Fitness UB-E920 User manual

USER GUIDE
Wheelchair
Accessible
UB - E920

2
Introduction
Congratulations on your purchase of E920.
FIRST DEGREE FITNESS is proud to present the Rower as a FULL COMMERCIAL USE
product featuring patented Adjustable Fluid Resistance.
As with any piece of fitness equipment, consult a physician before beginning your E920
exercise program.
Follow all instructions carefully for correct assembly, tank filling, water treatment,
service and safety.
Access to our world-wide distributor and service network is available at
www.firstdegreefitness.com
Check contents of Box 1 and Box 2 to assure all parts are present and correct prior to
assembly.
Training with the E920
WARNING
Do not remove hands while crank is in motion. The crank will continue to rotate and could
cause injury.

3
Contents
Safety ................................................................................... 4
Assembly - UB-E920............................................................... 6
UB-920 Box 1 & 2 Contents .................................................... 7
Assembly Instructions ............................................................. 8
Operation Instructions ............................................................... 13
Maintenance ............................................................................... 18
Troubleshooting .......................................................................... 19
Tank Belt Adjustment ................................................................. 20
International Warranty .......................................................... 21

4
Safety
Safety Information
•Before using this product, it is essential to read this ENTIRE operation manual and
ALL instructions. The Rower is intended for use solely in the manner described in this
manual.
•UNDERSTANDING EACH AND EVERY WARNING TO THE FULLEST IS IMPORTANT
•As with any piece of fitness equipment, consult a physician before beginning your
Rower exercise program.
•Please be aware that any fitness regiment, before being undertaken, is best preceded
by a physical checkup from a certified physician.
•Injuries to health may result from incorrect or excessive training.
• WARNING Heart rate monitoring systems may be inaccurate. Over exercise may
result in serious injury or death. If you feel faint, stop exercising immediately.
•Do not allow children unattended access to the machine.
•Please keep hands away from moving parts, as indicated by the warning label on the
mainframe of your machine.
•If any of the adjustment devices are left projecting, they could interfere with the
user’s movement.
•Do not store in freezing conditions with water in the tank as it can expand and crack
the components.
Installation
•Place on a stable, flat surface in a horizontal position during use for maximum
stability.
•Check regularly and follow all instructions for maintenance as specified in this manual.
•Replace immediately any defective parts and do not operate unit until all repairs are
complete.

5
Safety
Proper Usage
• Do not use any equipment in any way other than designed or intended by the
manufacturer. It is imperative that FIRST DEGREE FITNESS equipment is used
properly to avoid injury.
• Injuries may result if exercising improperly or excessively. It is recommended that all
individuals consult a physician prior to commencing an exercise program. If at any time
during exercise you feel faint, dizzy or experience pain, STOP EXERCISING and consult
your physician.
• Keep body parts (hands, feet, hair, etc.), clothing and jewelry away from moving parts
to avoid injury.
• Follow instructions provided in this manual for correct foot position and basic rowing
techniques.
• For more detailed rowing techniques, please refer to our International website
www.firstdegreefitness.com
Inspection
• DO NOT use or permit use of any equipment that is damaged and/or has worn or broken
parts. For all FIRST DEGREE FITNESS equipment use only replacement parts supplied by
FIRST DEGREE FITNESS.
• EQUIPMENT MAINTENANCE - Preventative maintenance is the key to smooth operating
equipment as well as to keep your liability to a minimum. Equipment needs to be
inspected at regular intervals.
• Ensure that any person(s) making adjustments or performing maintenance or repair of
any kind is qualified to do so.
• DO NOT ATTEMPT TO USE OR REPAIR ANY ACCESSORY APPROVED FOR USE WITH THE
FIRST DEGREE FITNESS EQUIPMENT WHICH APPEARS TO BE DAMAGED OR WORN.
• Check regularly and follow all instructions for maintenance as specified in this manual.
• Replace immediately any defective parts and do not operate unit until all repairs are
complete.
Operating Warnings
• Keep children away from the equipment. Parents or others supervising children must
provide close supervision of children if the equipment is used in the presence of children.
• Do not allow users to wear loose fitting clothing or jewelry while using equipment. It is
also recommended to have users secure long hair back and up to avoid contact with
moving parts.
• All bystanders must stay clear of all users, moving parts and attached accessories and
components while machine is in operation.
• WARNING Do not insert fingers into tank!

6
Assembly - UB-E920
Live area and Training area
Product Specifications
Product Class: SC
Braking System: Speed Independent
Product Net Weight: 90kg (198lb)
Product Gross Weight: 110kg (242lb)
Maximum Safe Operating Surface Area: 301cm (108.27”) Length x 222cm (87.40”) Width
Dimensions: 1810mm (71.26”) Length x 1020mm (40.16”) Width x 148mm (58.27”) Height
Maximum User Weight: 150kg (330lb)
Seat Frame
Product Highlights
Main frame
Integrated
Performance
Control Arm
Patented Twin
Tank Design
Telescoping tube / gas assisted shock
Complete Platform

7
UB-E920 Box 1 & 2 Contents
Item Qty.Description Item Qty. Description
1 1 Main Frame with Telescoping Tube
and Internal Gas Assist Shock 18 9 Foot Levelers
2 1 Baseplate 19 1 Handle Bar & Nut Dome Head
3 1 Seat Frame 20 1 Funnel and Hose
4 1 Seat Back 21 1 Touch up paint
5 1 Lower Seat 22 2 Handle Lock Knob
6 8 M6x20mm bolt 23 2 M12 Washer
7 4 M8x15mm bolt 24 2 Plastic Spacer
8 8 M8x20mm bolt 25 1 Slider Arm Assembly Left
9 4 M8x25mm bolt 26 1 Slider Arm Assembly Right
10 8 M8x45mm bolt 27 1 3mm Allen Key
11 3 M10x20mm bolt 28 1 4mm Allen Key
12 4 M8 Nylock Nut 29 1 6mm Allen Key
13 2 M10 Nylock Nut 30 1 Multi-tool
14 8 M6 Washer 31 2 AA Batteries
15 4 M8 Washer 32 4 Water Treatment Tablet
16 3 M10 Washer 33 1 Owners Manual
17 4 M8 Springs Washer

8
Assembly Instructions
8
STEP 1 Mainframe Assembly Instructions
a) Attach Telescoping Tube to the underside of the
control arm using 4x M8x15mm Bolts[7] and 4x M8
Spring Washers[17].
b) Thread the 3x Foot levelers[18] into underside of base.
Adjust as required.
2
1
12
REQUIRED
4 x M8 x 15mm Blots [7]
4 x M8 Spring Washers [17]
3 x Foot Levelers [18]
1
STEP 2
8
CAUTION
The control arm is heavy and
may swing freely during this
stage of assembly. The
Adjuster Knob is pre-tightened
from the factory in the optimal
position for assembly in relation
to the control arm. Do not
loosen the Adjuster knob until
the Telescoping Tube has been
safely secured to the underside
of the control arm.
Slider Arm Kit Installation Instructions
M8 Spring Washers
Adjuster Knob
Foot Leveler
M8x15mm Bolts
REQUIRED
2 x Handle Lock Knobs [22]
2 x M12 Washer [23]
2 x Plastic Spacer [24]
Slider Arm Assembly Left [25]
Slider Arm Assembly Right [26]
3mm Allen Key [27]
Slider Arm Assembly Left
Slider Arm Assembly Right
Handle Lock Knobs
M12 Washer
Plastic Spacer
Note: Slider Arms are
marked ‘L’ and ‘R’.
Improper installation will
result in uneven Slider Arm
adjustment

9
Assembly Instructions
STEP 3a Installing Baseplate to the Mainframe
1
8
2
1
12
REQUIRED
T-Track
Ramp Right
Ramp Left
2 x PVC Side Covers
3 x M10x20mm Blots [11]
2 x M10 Nylock Nut [13]
3 x M10 Washer [16]
Remove contents from box
and make sure all parts are
present. Contents will
include the T-track, left/right
side ramps and bolt pack
(note, this may also be
located with Seat Assembly).
Note hardware bolt pack is
used for both Seat Assembly
and Baseplate.
a) Bolt the T-Track to the Mainframe as shown, using
3x M10x20mm Bolts[11], 2x M10 Nylock Nut[13]
and 3x M10 Washers[16]. Secure tightly.
T-Track
Ramp Left
Ramp Right
PVC Side Covers
M10 Nylock Nut
M10 x20mm Blot
M10 Washer

10
Assembly Instructions
STEP 3b Installing Baseplate to the Mainframe
2
1
12
REQUIRED
4 x M8 x20mm Bolts [8]
4 x M8 x25 Blots [9]
8 x M8 x45mm Blots [10]
4 x M8 Nylock Nut [12]
4 x M8 Washers [15]
1
b) Attach Left and Right Ramps to the T-Track using 8x
M8x45mm Bolts[10].
c) Once the Left and Right Ramps have been installed to
the sides of the T-Track, secure the front end of each
Ramp as shown using 4x M8x25 Bolts[9], 4x M8
Nylock Nut[12] and 4x M8 Washers[15].
8
M8 x20mm Blot
d) Install Yellow PVC side covers using 4x M8x20mm Bolt
[8].
M8 x45mm Blot
M8 Washer
M8 Nylock Nut
M8 x25mm Blot

11
Assembly Instructions
STEP 4 Installing Seat Assembly
1
REQUIRED
Seat Frame [3]
Seat Back [4]
Lower Seat [5]
4 x M6x20mm Bolts [6]
M10 Dome Nut [13
4 x M6 Washer [14]
Handle Bar [19]
a) Thread the Handle Bar[19] through the Shaft
b) Tighten the Handle Bar[19] with the M10 Dome Nut[13].
c) Install Seat Back[4] with 4x M6x20 Bolts[6] and M6
Washer[14].
d) Install Lower Seat[5] with 4x M6x20 Bolts[6] and M6
Washer[14].
b)
a)
c)
d)
Seat Frame
Seat Back
Handle Bar
M6 x 20 Bolt
M6 Washer
M10 Dome Nut
Lower Seat

12
Assembly Instructions
STEP 5 Installing Seat to the Mainframe
a) Seat Stop: Must be lowered to allow seat onto
Baseplate track. Must ALWAYS be in the LOCKED
position when seat is occupied on Baseplate. Must
be lowered to allow seat removal. To LOCK, raise and
locate. To UNLOCK, lift and drop rearward.
CAUTION
The Seat Stop Must be in
the locked position whenever
the seat is in use..
WARNING
Do not under any
circumstances attempt to
remove / install seat while
occupied.
b) Seat Installation: Tilt the seat slightly upward to allow
the front rollers to engage the channel. Then, lift the
rear level and, while engaging the Seat Lock Release
Lever, slide the seat onto the Baseplate as shown.
Usage: The seat has four positions. To move forward
or rearward, depress the Seat Lock Release Lever
and move freely to whichever position you require.
c) To remove the seat: Lift and lower the Rear Safety lock,
depress the Seat Lock Release Lever and slide the seat
rearward.

13
Operation Instructions
Chain Tensioning Bolts: Allows for tightening the chain or adjustment from side to
side. Make sure when tightening only to adjust the same amount for both bolts,
otherwise the sprocket will be misaligned.
Note: Tightening the right bolt only (turning clockwise) will pull the right side of the
crank assembly toward you, tightening the left will pull the left side toward you.
Use this feature to realign the rear with the front sprocket if needed or when
changing to a new chain.
E920 Control Arm
Handgrip: Loosen knob to adjust
handle position from 0-90 degrees.
Crank Arm Bolts: Loosen all 8
bolts slightly before adjusting/
tightening chain.
Inspection plate: Open to check
chain tension.
With a screwdriver or other
implement, check tension just
behind front sprocket.
Note: A properly adjusted chain
will have 3mm-5mm of slack only.
See top of page for adjustment
details.
Warning: Do not check
chain tension by fingers!
Adjustment Knob: Loosen to
allow the control arm to travel
through 90 degrees of travel.
Note the Telescoping Tube is
gas assisted.
Tighten securely when desired
workout position is reached.
E920 Slider Arms: Refer
to following assembly page.

14
Operation Instructions
a) Mount the left Slider Arm onto the Axle using the yellow indicator hole to align
the slider and axle.
b) Tighten the set screw onto the Axle and into the yellow indicator hole using the
3mm Allen key.
c) Thread Adjustment Knob onto the Axle to secure the assembly.
d) Repeat steps 1-3 to install right Slider Arm onto the Axle.
a)
b)
c)
d)
The E920 Slider Arm Kit offers the user an entire
range of added resistance settings and the ability to
perform additional upper body workouts.
To adjust, simply loosen the Adjustment Knobs, move
Slider Arm to desired length and secure. Very little
tension is needed.
What do the numbers mean?
The numbers represent the length (in cm) from the
center of the Axle to the center of the Handgrip Shaft
Bolt. The shortest Slider Arm length is 12cm and the
maximum length is 21cm. The range of adjustment is
9cm.
Using Slider Arm
Slider Arm Kit Installation Instructions

15
Operation Instructions
Additional Exercises
Training can now be achieved with both left and
right Handgrips moving parallel , rather than in an
opposed motion.
a) On the right Slider Arm Assembly, remove the
Adjustment Knob, loosen set screw and remove
Assembly from the Axle.
b) As shown below, rotate right Slider Arm 180
degrees and reinstall onto the Axle. There is
an additional screw locator hole located on
opposite side of axle .

16
Operation Instructions
Note: The Lower Black Tank Plug is Permanently Sealed.
INITIAL WATER TREATMENT
Add 1 x Water Treatment Tablet per full tank. DO NOT, UNDER ANY CIRCUMSTANCE,
USE A WATER TREATMENT TABLET OTHER THAN THOSE SUPPLIED WITH YOUR UNIT.
Your unit purchase includes 4 x Water Treatment Tablets, which is sufficient for
several years of use. To purchase additional chlorine tabs, please consult your nearest
regional dealer/distributor or check our website at www.firstdegreefitness.com
a) Filling requires a large bucket (not Supplied) and the supplied
water Funnel and Hose[20]. Filling will take approximately 8
liters of water.
b) Open the yellow fill plug on the back of the tank and insert hose
(rotating the impeller slightly may be necessary to allow the
hose to pass). Note: In areas where tap water quality is known
to be poor, FDF recommends the use of distilled water.
c) Move the Tank Adjuster Handle to Level 20 and begin filling. Do
not fill the tank higher than the level indicator on the front of
the clear shell.
d) Once filling is complete follow the water treatment procedure
below, then replace the tank plug.
REQUIRED
Funnel and Hose [20]
Yellow Tank Plug
Filling Hose and Funnel
Resistance:
The level of resistance is
determined by the Level
Indicator located on the
front of the tank. Level one
indicates lightest resistance,
level twenty represents
heaviest resistance. Allow
three to four seconds after
adjusting resistance handle
for the correct resistance
WARNING
Removing hands before
the crank comes to a
complete stop while
training can cause
injury. The crank is
direct drive so as to
allow both forward and
reverse rotation during
workouts.
Long Term Water Treatment and Basic Operation
Water treatment schedules for the E920 will vary according to the fluid tanks exposure
to sunlight but expect 8-12 months near a bright, sunlit window and 2-4 years for a
darker location. At the point of finding the water slightly green, add a Chlorine tablet.
CAUTION
Use a drop cloth under
the tank when filling to
avoid damage floor or
carpet.
Do not fill past the
calibration mark as
indicated on the tank
level sticker or water
spillage may occur.
WARNING
Impeller blades are
sharp! Do not Place
fingers in tank to
adjust impeller position.
It is recommended to
use the end of the hose
Should the impeller
require adjustment.
Tank Filling and Water Treatment

17
Operation Instructions
Quick start: Provides instant workout
information. Just start training to activate.
You can choose to change UNITS displayed
UNITS: Displays WATTS, SPM, HR, 500/m
LEVEL: Adjustable from 1-20. Match LEVEL
number with resistance level on the Fluid
tank.
SET: Changes Time, Distance parameters
PROGRAM: Clears current exercise program
RESET: Clears data
Note: For complete operational instructions,
please refer to the computer manual, which is
included with your Rower.
Integrated Performance Monitor [IPM] Operation
Using the First Degree Fitness USB Interface
Description:
The USB connectivity now built in to all new models of FDF Console and IPM allow you
to enhance your exercise experience by connecting to your home PC or Laptop. Using
FDF's own sample applications you can exercise while enjoying your favorite movies.
NetAthlon 2 XF for Rowers lets you race with other Internet connected rowers in a
Virtual Reality 3D environment or train solo.
Setting Up USB connectivity
1.Download and Install the USB Device Driver (CDM2xxxx_Setup.exe for 32 and 64 bit
Windows 7/Vista/XP) from the FDF Website.
2.Download and Install the Sample USB Applications from the FDF Website
(www.firstdegreefitness.com).
Download and Install NetAthlon 2 XF for Rowers from.
http://www.webracing.org/downloads.htm
Connecting Your Console
- The USB Connector is located on a flying lead at the rear of the IPM, along with the Sensor and Heart
Rate Monitor Connectors.
- Connect to a Laptop or PC using a standard USB cable, you may need to wait while Windows starts the
USB Device Driver.
Note: Please refer to computer manual where applicable or for further information refer
to our website at www.firstdegreefitness.com

18
Maintenance
Item Time Frame Instructions Notes
Seat and Frame. Weekly. Wipe down weekly with lint free cloth
or more often with heavy club use.
PK Belt Tension. Monthly. Check monthly for signs of slippage.
Adjust/tighten as required.
Tank and Water
Treatment.
12 months to 2
years.
Follow instructions as specified in the
“Water Treatment” section of this
manual.
Chain Drive.
Check every 100
hours for correct
tension.
Open the inspection plate and check
tension using a screwdriver or other
tool. Tighten as required using chain
tensioning bolts located at the end of
the control arm.
Handle Assembly.
Check weekly using
Multi-Tool (supplied)
to ensure Handle
Assembly is securely
tightened into Crank
Arm.
The handle should be checked on a
regular basis.
Continued use of a loose Handgrip can
cause
damage to the Crank Arm threads,
necessitating replacement.
All preventive maintenance activities must be performed on a regular basis. Performing
routine preventive maintenance actions can aid in providing safe, trouble-free operation
of all First degree fitness equipment.
First degree fitness is not responsible for performing regular inspection and maintenance
actions for your machines. Instruct all personnel in equipment inspection and maintenance
actions and also in accident reporting and recording.
FIRST DEGREE FITNESS representatives are available to answer any questions that you
may have.

19
Troubleshooting
Fault Probable Cause Solution
Water changes color
or becomes cloudy.
Rower is in direct
sunlight or has not
had water treat-
ment.
Change rower location to reduce direct
exposure to sunlight. Add water treatment
or change tank water as directed in the
water treatment section of this manual.
Consider using distilled water to refill tank.
Knocking noise from
inside the control
arm while training,
especially when
changing directions.
Chain requires
tightening or
adjustment.
Open inspection plate located on front of
control arm and check tension using a
screwdriver or other tool. Use the chain
tensioning bolts located at the rear of the
control arm to tighten or adjust as
needed. The chain should have approx 3mm
of slack when properly adjusted. See P.7
for details.
Handle slip during
hard training.
PK tank belt
requires
tightening.
Remove large inspection plate next to the
tank, insert a long tool to push the rear
end cap out from the inside, exposing the
Tank Belt Tensioning Bolt. Loosen tank
bolts slightly. Remove upper rubber belt
cover to expose the PK belt. Tighten the
Tank Tensioning Bolt until the Belt is too
tight to be twisted from side to side more
than 45 degrees by hand. See P.17/18 for
details
Handle is loose
(either left or right)
and cannot be
retightened.
Aluminum crank
arm threads are
stripped.
Contact service center for replacement.
Then check weekly as recommended.
IPM screen
illuminates, but does
not register when
rowing.
Loose or failed
connection/Sensor
gap too wide (see
erratic computer
display).
Check that the computer lead is connected
properly. If connected properly check
sensor gap. Contact your local service
center if this fails to address the problem.
IPM does not
illuminate after
battery installation.
Batteries installed
incorrectly or need
replacing.
Reinstall batteries in correct position and
try again. If the LCD screen fails to
illuminate, try rotating the batteries
slightly in the computer. If this fails,
contact your local service center.
IPM is erratic/slow
while displaying RPM
and WATTS
Gap between
sensor and
magnetic ring is
too wide.
Remove inspection plate and check sensor
gap and that magnetic ring is not wobbly.

20
Tank Belt Adjustment
1. Remove large metal inspection plate. 2. Using a long tool, push out the rear
end cap as pictured below left. This
will give you access to the tank
3. Loosen both the rear and front tank
bolts slightly as shown. Remove
front Rubber Belt Cover.
4. Using a 6mm Allen Key, tighten the
Belt using the Tank Tensioning Bolt
until the belt no longer slips during
hard rowing.
End Cap
Note: Do not over tighten tank bolts.
Tip: Twist the Belt by hand to gauge
tightness. Correct tension should be
obtained when no longer able to twist
more than 45 degrees
Tank Tensioning Bolt