FISCHER ME11 Series User manual

Operating manual
ME11
Pressure Transmitter
09005184 • BA_EN_ME11 • Rev. ST4-B • 04/22 *09005184*

| Masthead FISCHER Mess- und Regeltechnik GMBH
2/24 BA_EN_ME11
Masthead
Manufacturer: FISCHER Mess- und Regeltechnik GmbH
Bielefelderstr. 37a
D-32107 Bad Salzuflen
Telephone: [phone]
Telefax: [phone]
eMail: [email protected]
web: www.fischermesstechnik.de
Technical editorial team: Documentation representative: T. Malischewski
Technical editor: R. Kleemann
All rights, also those to the translation, reserved. No part of this document may
be reproduced or processed, duplicated or distributed using electronic systems
or any other form (print, photocopy, microfilm or another process) without the
written consent of the company FISCHER Mess- und Regeltechnik GmbH, Bad
Salzuflen.
Reproduction for internal use is expressly allowed.
Brand names and procedures are used for information purposes only and do
not take the respective patent situation into account. Great care was taken
when compiling the texts and illustrations; Nevertheless, errors cannot be ruled
out. The company FISCHER Mess- und Regeltechnik GmbH will not accept any
legal responsibility or liability for this.
Subject to technical amendments.
© FISCHER Mess- und Regeltechnik GmbH 2015
Version history
Rev. ST4-A 09/15 Version 1 (first edition)
Rev. ST4-B 04/22 Version 2 (UKCA Declaration of Conformity)

FISCHER Mess- und Regeltechnik GMBH Table of contents
BA_EN_ME11 3/24
Table of contents
1 Safety guidelines ............................................................................................................. 4
1.1 General................................................................................................................................... 4
1.2 Personnel Qualification........................................................................................................... 4
1.3 Risks due to Non-Observance of Safety Instructions............................................................. 4
1.4 Safety Instructions for the Operating Company and the Operator ......................................... 4
1.5 Unauthorised Modification...................................................................................................... 4
1.6 Inadmissible Modes of Operation........................................................................................... 5
1.7 Safe working practices for maintenance and installation work............................................... 5
1.8 Pictogram explanation............................................................................................................ 5
2 Product and functional description ............................................................................... 6
2.1 Intended use........................................................................................................................... 6
2.2 Product summary ................................................................................................................... 6
2.3 Function diagram.................................................................................................................... 7
2.4 Design and mode of operation ............................................................................................... 7
3 Installation and assembly ............................................................................................... 8
3.1 Generalities ............................................................................................................................ 8
3.2 Process connection ................................................................................................................ 8
3.3 Electrical connections............................................................................................................. 10
3.4 Commissioning ....................................................................................................................... 12
4 Servicing........................................................................................................................... 13
4.1 Maintenance ........................................................................................................................... 13
4.2 Transport ................................................................................................................................ 13
4.3 Service.................................................................................................................................... 13
4.4 accessories............................................................................................................................. 13
4.5 Disposal.................................................................................................................................. 13
5 Technical Data ................................................................................................................. 14
5.1 General information................................................................................................................ 14
5.2 Input variables ........................................................................................................................ 14
5.3 Output parameters.................................................................................................................. 15
5.4 Measurement accuracy .......................................................................................................... 15
5.5 Auxiliary energy ..................................................................................................................... 15
5.6 Operating conditions............................................................................................................... 15
5.7 Construction design................................................................................................................ 16
6 Order Codes ..................................................................................................................... 18
7 Attachments ..................................................................................................................... 21

1 | Safety guidelines FISCHER Mess- und Regeltechnik GMBH
4/24 BA_EN_ME11
1 Safety guidelines
1.1 General
This operating manual contains basic instructions for the installation, operation
and maintenance of the device that must be followed without fail. It must be
read by the installer, the operator and the responsible specialist personnel be-
fore installing and commissioning the device.
This operating manual is an integral part of the product and therefore needs to
be kept close to the instrument in a place that is accessible at all times to the re-
sponsible personnel.
The following sections, in particular instructions about the assembly, commis-
sioning and maintenance, contain important information, non-observance of
which could pose a threat to humans, animals, the environment and property.
The instrument described in these operating instructions is designed and manu-
factured in line with the state of the art and good engineering practice.
1.2 Personnel Qualification
The instrument may only be installed and commissioned by specialized person-
nel familiar with the installation, commissioning and operation of this product.
Specialized personnel are persons who can assess the work they have been
assigned and recognize potential dangers by virtue of their specialized training,
their skills and experience and their knowledge of the pertinent standards.
1.3 Risks due to Non-Observance of Safety Instructions
Non-observance of these safety instructions, the intended use of the device or
the limit values given in the technical specifications can be hazardous or cause
harm to persons, the environment or the plant itself.
The supplier of the equipment will not be liable for damage claims if this should
happen.
1.4 Safety Instructions for the Operating Company and the
Operator
The safety instructions governing correct operation of theinstrument must be
observed. The operating company must make them available to the installation,
maintenance, inspection and operating personnel.
Dangers arising from electrical components, energy discharged by the medium,
escaping medium and incorrect installation of the device must be eliminated.
See the information in the applicable national and international regulations.
Please observe the information about certification and approvals in the Tech-
nical Data section.
1.5 Unauthorised Modification
Modifications of or other technical alterations to the instrument by the customer
are not permitted. This also applies to replacement parts. Only the manufacturer
is authorised to make any modifications or changes.

FISCHER Mess- und Regeltechnik GMBH Safety guidelines | 1
BA_EN_ME11 5/24
1.6 Inadmissible Modes of Operation
The operational safety of this instrument can only be guaranteed if it is used as
intended. The instrument model must be suitable for the medium used in the
system. The limit values given in the technical data may not be exceeded.
The manufacturer is not liable for damage resulting from improper or incorrect
use.
1.7 Safe working practices for maintenance and installation work
The safety instructions given in this operating manual, any nationally applicable
regulations on accident prevention and any of the operating company's internal
work, operating and safety guidelines must be observed.
The operating company is responsible for ensuring that all required mainten-
ance, inspection and installation work is carried out by qualified specialized per-
sonnel.
1.8 Pictogram explanation
DANGER
Type and source of danger
This indicates a direct dangerous situation that could lead to death or serious
injury (highest danger level).
1. Avoid danger by observing the valid safety regulations.
WARNING
Type and source of danger
This indicates a potentially dangerous situation that could lead to death or ser-
ious injury (medium danger level).
1. Avoid danger by observing the valid safety regulations.
CAUTION
Type and source of danger
This indicates a potentially dangerous situation that could lead to slight or seri-
ous injury, damage or environmental pollution (low danger level).
1. Avoid danger by observing the valid safety regulations.
NOTICE
Note / advice
This indicates useful information of advice for efficient and smooth operation.

2 | Product and functional description FISCHER Mess- und Regeltechnik GMBH
6/24 BA_EN_ME11
2 Product and functional description
2.1 Intended use
The ME11 is a pressure transmitter with a ceramic measuring cell that is suit-
able for measuring over-pressure and under-pressure in non-aggressive liquid
and gaseous media.
NOTICE
Soiled or aggressive media
Please contact the manufacturer before using this unit with dirty or aggressive
media because the unit needs to be adapted for the specific customer in terms
of the parts that come into contact with the media.
The device may only be used for the purpose stipulated by the manufacturer.
2.2 Product summary
The following provide an overview of the possible connectors and process con-
nections. The code stated corresponds to the respective code in the order code.
Electrical plug
Line socket
DIN EN 175 301-803-A
Circular plug connector M12
DIN EN 61076-2-101
(flanged connector)
Code H M
Fig.1: Electrical plug
Process connections
Code 85 87 88 S1
G½ B ¼ -18 NPT EXTG¼ B Schrader ®
Fig.2: Process connections

FISCHER Mess- und Regeltechnik GMBH Product and functional description | 2
BA_EN_ME11 7/24
Nameplate
This type plate serves as an example of the information that is stated. The data
shown is purely fictive, but does correspond to the actual conditions. For more
information, please see the order code at the end of these instructions.
Reference code
Technical data
Serial number
Circuit diagram
Marking
Special properties
Type
Measuring range
Electr.Output
Operating voltage
Prod. no.
Silicone-free
Fig.3: Nameplate
2.3 Function diagram
Pressure pΔR
R
U/I U
Δ
b
out
1
2 3
4
5
Fig.4: Function diagram
1 Ceramic sensor 2 electronics
3 Auxiliary energy 4 Electrical connection
5 Process connection
2.4 Design and mode of operation
The measuring pressure acts on a ceramic membrane that deforms when under
pressure. There is a DMS bridge attached to the ceramic membrane. When the
ceramic deforms, the output signal of the DMS bridge changes. The electronics
integrated into the device convert the bridge signals into electrical unit signals
4...20mA or 0…10VDC um.

3 | Installation and assembly FISCHER Mess- und Regeltechnik GMBH
8/24 BA_EN_ME11
3 Installation and assembly
3.1 Generalities
The instrument may only be installed and commissioned by specialized person-
nel familiar with the installation, commissioning and operation of this product.
Specialized personnel are persons who can assess the work they have been
assigned and recognize potential dangers by virtue of their specialized training,
their skills and experience and their knowledge of the pertinent standards.
WARNING
Mounting pressure transmitters
During assembly, observe the respective national and international guidelines
and safety regulations.
Only mount the unit to systems that are depressurized. Only ever operate the
unit within the permitted measuring range or below the maximum overload.
Fig.5: Shutoff valve.
The device is set ex-works for vertical installation, however any installation posi-
tion is possible.
To guarantee safe working conditions during installation and maintenance, suit-
able stop valves must be fitted in the system (see accessories). By means of
the manometer shutoff, the unit
• Can be depressurized or taken out of operation.
• Be disconnected from the power supply within the applicable system for re-
pairs or inspections.
3.2 Process connection
• By authorized and qualified specialized personnel only.
• The pipes need to be depressurized when the instrument is being connec-
ted.
• Appropriate steps must be taken to protect the device from pressure surges.
• Check that the device is suitable for the medium being measured.
• Maximum pressures must be observed (cf. Tech. data)
WARNING
Earth connection via the system earth
During assembly, ensure that the earth connection between the unit and the
system earth is ensured. The connection to the system earth is realised via the
process connection. Therefore, never use an insulated Teflon tape or similar.
Design the process connection acc. to EN 837 and use a suitable flat seal.

FISCHER Mess- und Regeltechnik GMBH Installation and assembly | 3
BA_EN_ME11 9/24
3.2.1 Measuring lines that need to be connected
The following points need to be observed when connecting the pressure line:
• To ensure there is no influence on the measured values, severe bends and
coils in the wire should be avoided.
• To prevent deposits, there should be a continuous incline or drop of at least
8%.
• When measuring steam pressure, a water bag-forming loop must be
provided due to the temperature (see accessories).
Round shape U-shape
G½
ca. 180
Ø20
56
155
ca. 200
G½
G½
ca. 275
ca. 130
Ø20
Ø56
G½
AF27
Manometer connection
Connection spigot
according to
DIN EN 837-1
Fig.6: Siphon MZ1###
• The transmitter must be positioned below the measuring point for liquid
measurements. Vent the pressure line before commissioning.
• The transmitter must be positioned above the measuring point for gas
measurements.
3.2.2 Pressure surge absorption
Pulsating pressure on the system side can lead to functional problems. We re-
commend installing a damping element in the pressure connection lines as a
protective measure.
a) Capillary throttle
Manometer connection
SW27 AF27
Connection spigot
according to DIN EN 837-1
305
110
G½ G½
Ø88
Ø4
Fig.7: Capillary throttle MZ400#

3 | Installation and assembly FISCHER Mess- und Regeltechnik GMBH
10/24 BA_EN_ME11
b) Settable damping reactor
In operating mode, the damping throttle must be set so that the output signal
follows the pressure changes with a delay.
G½
G½
20
66
19
AF27
Setting screw
Connection spigot
according to DIN EN 837-1
Manometer connection
Fig.8: Damping reactor MZ410#
3.3 Electrical connections
• By authorized and qualified specialized personnel only.
• When connecting the unit, the national and international electro-technical
regulations must be observed.
• Disconnect the system from the mains, before electrically connecting the
device.
• Install the consumer-adapted fuses.
• Do not connect the connector if strained.
a) 2-wire connection
Input signal
Supply
+Sig
-Sig
+Ub
-Ub
Output signal
Pressure Transmitter
Fig.9: 2L Circuitry

FISCHER Mess- und Regeltechnik GMBH Installation and assembly | 3
BA_EN_ME11 11/24
b) Three-wire connection
Pressure Transmitter Supply
Output signal
Input signal
+Sig
+/~Ub
-/~Ub -Sig
+/~Ub
-/~Ub
AC/DCAC/DC
AC
Fig.10: 3L circuitry AC/DC
3.3.1 Standardised plug DIN EN 175 301-803-A
1
3
2
Cable screw connection
M16x1.5
Seal NBR
Contact insert
Housing
Screw 1
2
3
Line socket Flanged connector
Fig.11: Line socket DIN EN 175 301-803-A
Ter-
minal
Signal name DC Cable colour
1 Supply /Output +Ub+Sig red
2 Supply /Output -Ub-Sig blue
3 n.c.
n.c.
Table1: 2-wire connection 4 ... 20 mA
Ter-
minal
Signal name AC DC Cable colour
1 Output +Sig Black
2 Supply /Output ~Ub-Ub-Sig blue
3 Supply ~Ub+Ubred
n.c.
Table2: 3-wire connection 0 ... 10V
The earth connection in the standardized plug is not connected.

3 | Installation and assembly FISCHER Mess- und Regeltechnik GMBH
12/24 BA_EN_ME11
3.3.2 M12 flanged connector DIN EN 61076-2-101
Coding A
1
43
21
4 3
2
Flanged
connector
Line socket
Fig.12: M12 plug DIN EN 61076-2-101
Pin Signal name DC Cable colour
1 Supply /Output +Ub+Sig brown
2 n.c.
3 Supply /Output -Ub-Sig blue
4 n.c.
Table3: 2-wire connection 4 ... 20 mA
Pin Signal name AC DC Cable colour
1 Supply ~Ub+Ubbrown
2 n.c.
3 Supply /Output ~Ub-Ub-Sig blue
4 Output +Sig Black
Table4: 3-wire connection 0 ... 10V
3.4 Commissioning
All electrical supply, operating and measuring lines and the pressure connec-
tions must have been correctly installed before commissioning. All supply lines
are arranged so that there are no mechanical forces acting on the device.
• If liquid measuring media are used the pressure connection lines must be
vented, as liquid columns of different heights in the pipes can cause meas-
uring errors. The instrument must be protected against frost, if water is used
as a measuring medium.
• Appropriate shutoff valves must be provided to ensure safety during installa-
tion, maintenance and inspection

FISCHER Mess- und Regeltechnik GMBH Servicing | 4
BA_EN_ME11 13/24
4 Servicing
4.1 Maintenance
The instrument is maintenance-free. We recommend the following regular in-
spection to guarantee reliable operation and a long service life:
• Check the function in combination with downstream components.
• Check the leak-tightness of the pressure connection lines.
• Check the electrical connections.
The exact test cycles need to be adapted to the operating and environmental
conditions. In combination with other devices, the operating instructions for the
other devices also need to be observed.
4.2 Transport
The measuring device must be protected against impacts. It should be transpor-
ted in the original packaging or a suitable transport container.
4.3 Service
All defective or faulty devices should be sent directly to our repair department.
Please coordinate all shipments with our sales department.
WARNING
Process media residues
Process media residues in and ondismantled devices can be a hazard to
people, animals and the environment. Take adequate preventive measures. If
required, the devices must be cleaned thoroughly.
Return the device in the original packaging or a suitable transport container.
4.4 accessories
• Prefabricated M12 connection lines (pageOrder Codes [}18])
• Siphons MZ1###
• Capillary throttle coil MZ400#
• Settable damping reactor MZ410#
• Manometer shutoff valves MZ5###, MZ6###
Please see here the data sheet MZ measuring devices accessories. Here you
will find more detailed information about the technical data and the order codes
of the accessory parts MZ.
4.5 Disposal
Please help to protect the environment by always disposing of the work pieces
and packaging materials in compliance with the valid national waste and recyc-
ling guidelines or reuse them.

5 | Technical Data FISCHER Mess- und Regeltechnik GMBH
14/24 BA_EN_ME11
5 Technical Data
5.1 General information
Reference conditions (acc. to IEC 61298-1)
Temperature +15 … +25 °C
Relative humidity 45 … 75 %
Air pressure 86 … 106 kPa 860 … 1060 mbar
Installation position User-defined
5.2 Input variables
Positive measuring ranges Measuring range Pressure safety
SI unit Overpres-
sure
Bursting-
pressure
0 … + 0.6 bar 0 … 60 kPa 4 bar 7 bar
0 … +1 bar 0 … 100 kPa 4 bar 7 bar
0 … +1.6 bar 0 … 160 kPa 4 bar 7 bar
0 … +2.5 bar 0 … 250 kPa 10 bar 15 bar
0 … +4 bar 0 … 400 kPa 10 bar 15 bar
0 … +6 bar 0 … 600 kPa 20 bar 35 bar
0 … +10 bar 0 … 1000 kPa 20 bar 35 bar
0 … +16 bar 0 … 1600 kPa 40 bar 70 bar
0 … +25 bar 0 … 2500 kPa 100 bar 150 bar
0 … +40 bar 0 … 4000 kPa 100 bar 150 bar
0 … +60 bar 0 … 6000 kPa 200 bar 250 bar
Vacuum and
± measuring ranges
Measuring range Pressure safety
SI unit Overpres-
sure
Bursting-
pressure
-1 … 0 bar -100 … 0 kPa 4 bar 7 bar
-1 … +0.6 bar -100 … 60 kPa 4 bar 7 bar
-1 … +1.5 bar -100 … 150 kPa 4 bar 7 bar
-1 … +3 bar -100 … 300 kPa 10 bar 15 bar
-1 … +5 bar -100 … 500 kPa 20 bar 35 bar
-1 … +9 bar -100 … 900 kPa 40 bar 70 bar
-1 … +15 bar -100 … 1500 kPa 40 bar 70 bar
-1 … +24 bar -100 … 2400 kPa 100 bar 150 bar
Special measuring ranges Measuring range Pressure safety
SI unit Overpres-
sure
Bursting-
pressure
0 … 30 PSI 0 … 206.8 kPa 10 bar 15 bar
0 … 60 PSI 0 … 413.7 kPa 10 bar 15 bar
0 … 100 PSI 0 … 689.4 kPa 20 bar 35 bar
0 … 160 PSI 0 … 1103.2 kPa 40 bar 70 bar
0 … 250 PSI 0 … 1723.6 kPa 40 bar 70 bar
0 … 500 PSI 0 … 3447.3 kPa 100 bar 150 bar
-30 inHg vac …+ 15 psi 4 bar 7 bar
-30 inHg vac …+ 100 psi 20 bar 35 bar

FISCHER Mess- und Regeltechnik GMBH Technical Data | 5
BA_EN_ME11 15/24
5.3 Output parameters
2-Conductor 3-Conductor
Output signal 4 … 20 mA DC 0 … 10 V DC
Limits Max. 21 mA Max. 10.5 V
Apparent ohmic resist-
ance
(Ub-6V)/0.02A Ub ≥ 15V ≥ 5kΩ
Ub ≥ 20V ≥ 2kΩ
5.4 Measurement accuracy
Non-linearity < 1.0 % FS
Hysteresis < 0.5 % FS
Characteristic curve deviation *) 1.0 %
Temperature drift Zero point 0.07 % FS/K
Measuring range 0.05 % FS/K
*) incl. non-linearity and hysteresis
5.5 Auxiliary energy
2-Conductor 3-Conductor
Rated Voltage 24v DC 24 V AC/DC
Admissible operating voltage 6 … 30 V DC 19.2 …28.8 V AC/DC
Power input 0.7 W 0.5 W (VA)
5.6 Operating conditions
Ambient temperature range 0 °C … +60 °C
Storage temperature range -20 °C … +85°C
Medium temperature range 0 °C … +85 °C
EMC EN 61326-1:2013
EN 61326-2-3:2013
RoHS EN 50581:2012
Type of protection: IP 65 acc. to EN 60529
Materials of the parts that come into contact with the surroundings
Casing CrNi Steel 1.4305
Device plug screw lid Polypropylene, black
Device plug Polyamide, brass, zinc
Cable socket Polyamide, polycarbonate, brass, zinc
Materials of the parts that come into contact with the measuring medium
Process connection CrNi Steel 1.4404
Sensor membrane Ceramic Al2O3
Seal 1) FKM Fluorinated rubber, Viton®
CR Chloroprene rubber, Neoprene®
EPDM Ethylene propylene diene rubber
H-NBR Hydrogenated acrylonitrile butadiene rubber
(for hot water applications)
1) see order code

5 | Technical Data FISCHER Mess- und Regeltechnik GMBH
16/24 BA_EN_ME11
5.7 Construction design
5.7.1 Standard casing dimensional drawing
All dimensions in mm unless otherwise stated
M12 x 1
72
Ø38.5
Ø28
SW27
91
20
3
G½
Ø6
Ø17.5
13
2
Ø5
G¼
Ø9.5
20
¼-18 NPT EXT
SW27
Schrader ®
7.5
Ø2
7/16 UNF
Ø21
Fig.13: Standard casing dimensional drawing

FISCHER Mess- und Regeltechnik GMBH Technical Data | 5
BA_EN_ME11 17/24
5.7.2 Process connection
¼-18 NPT EXT Connection shanks with external thread
Schrader©Connection for Schrader screw connection
G¾ B Connection shanks with external thread
G¼ B Connection shanks with external thread
5.7.3 Electrical connections
Fig.14: Line socket DIN EN 175
301-803-A
Unit connector and cable socket DIN EN 175 301-803 Form A, 4-pin
1
3
21
2
3
Line socketDevice plug
1 2
2-Wire
+ -
3-Wire
Sig
Ub
123
+-
Sig
Ub
3
nc
nc
~~
The earth connection is not connected.
Fig.15: M12 coupling device DIN
EN 61076-2-101
M12 flanged connector DIN EN 61076-2-101, 4-pin
Coding A
1
4
3
22
Flanged connector Coupling
43
1
1234
2-Wire
+ -
1234
3-Wire
+ -
Sig
Ub
Ub
Sig
~~

6 | Order Codes FISCHER Mess- und Regeltechnik GMBH
18/24 BA_EN_ME11
6 Order Codes
M
Process connection
Output signal
Operating voltage
Type of protection:
Mediumb. Seal
Electr. connection
Measuring system
M E 1 1
Type
Measuring range
0
1 2 5 6 7 8 9 10 11 123 4Code no.
Measurement accuracy
[1.2] Measuring range
01 0 … 0,6bar
02 0 … 1bar
03 0…1.6 bar
04 0…2.5 bar
05 0 … 4bar
06 0 … 6bar
07 0 … 10bar
08 0 … 16bar
09 0 … 25bar
10 0 … 40bar
11 0 … 60bar
31 -1 … 0 bar
32 -1…0.6 bar
33 -1…1.5 bar
34 -1…3 bar
35 -1…5 bar
36 -1…9 bar
37 -1…15 bar
38 -1…24 bar
F1 0 … 60 kPa
F2 0 … 100 kPa
F3 0 … 160 kPa
F4 0 … 250 kPa
F5 0 … 400 kPa
F6 0 … 600 kPa
F7 0 … 1000 kPa
F8 0 … 1600 kPa
G1 0 … 2500 kPa
G2 0 … 4000 kPa
G3 0 … 6000 kPa

FISCHER Mess- und Regeltechnik GMBH Order Codes | 6
BA_EN_ME11 19/24
H5 0 … 30 PSI
H6 0 … 60 PSI
H7 0 … 100 PSI
H9 0 … 160 PSI
Q1 0 … 250 PSI
P9 0 … 500 PSI
S2 -30 inHg vac … +15 psi
S2 -30 inHg vac … +100 psi
[3] Measurement accuracy
MCharacteristic curve deviation 1.0%
[4.5] Process connection
85 Connection shanks with external thread G¼ B
87 Connection shanks with external thread G½ B
88 Connecting port with outer thread ¼-NPT EXT
S1 Connection for Schrader ® screw connection
[6] Output signal Connection
type
Condition (Operating voltage)
B4 … 20 mA DC 2-Wire 24V DC
C0 … 10 V DC 3-Conductor 24 V AC/DC
[7] Electrical connection
H4-pin standard plug DIN EN 175 301-803-A
M4-pin M12 plug connection DIN EN 61076-2-101
[8] Operating voltage
924 V DC 2 wire output signal
A24 V DC 3 wire output signal
L24 V AC/DC 3 wire output signal
[9] Casing
0IP65
RIP65 (cast version)
[10] Media-Contact Seal Application
RFKM Fluorocarbon rubber For O2 measure-
ment mandatory
CCR Chloroprene Rubber
EEPDM Ethylene propylene diene rubber
HH-NBR Hydrogenated acrylonitrile
butadiene rubber
Hot-water
[11] Measuring system Condition
0Default
3Suitable for O2 measurements; O-ring FKM
(BAM tested) *)
ASilicon-free version
*) BAM:= Bundesanstalt für Materialforschung und –prüfung

6 | Order Codes FISCHER Mess- und Regeltechnik GMBH
20/24 BA_EN_ME11
6.1 Prefabricated connection lines
Order no. Designation No. of
Poles
length
06401993 PUR cable with M12-coupling 4-pin 2m
06401994 PUR cable with M12-coupling 4-pin 5m
06401563 PUR cable with M12-coupling 4-pin 7m
06401572 PUR cable with M12-coupling 4-pin 10m