Fisher & Paykel OR90LDBGFX3 User manual

Installation Instructions
Installation Instructions
Figure 1 Cooker Dimensions And Capacity
The cooker must be installed by a qualified technician and in compliance with local safety standards. This cookers has
class “2/1” overheating protection so that it can be installed next to a cabinet. If the cooker is installed adjacent to
furniture which is higher than the gas hob cooktop, a gap of at least 200 mm must be left between the side of the cooker
and the furniture. The furniture walls adjacent to the cooker must be made of material resistant to heat. The veneered
synthetical material and the glue used must be resistant to a temperature of 90°C in order to avoid ungluing or
deformations. The cooker may be located in a kitchen, a kitchen/diner or bed-sitting room but not in a room containing a
bath or shower. Curtains must not be fitted immediately behind appliance or within 500 mm of the sides.
If the cooker is located on a pedestal it is necessary to provide safety measures to prevent falling out.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
1

It is essential that the cooker is positioned as stated.
Figure 2 Correct Distances From Cooker
Fitting The Adjustable Feet
Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure
adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or
other support surface.
The adjustable feet must be fitted to the base of the cooker before use.
Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet.
Fit the four legs by screwing them tight into the support base as shown.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
2

Figure 3 Location of feet Figure
Figure 4 Top of feet screwed in tightly
Leveling The Cooker
Level the cooker by screwing the bottom of the feet in or out, as shown.
Figure 5 Levelling the cooker
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
3

Moving The Cooker
• Two people must always raise the cooker, as shown, to prevent damaging the adjustable feet.
• Do not lift the cooker by the door handles. DO NOT DRAG the cooker. Lift the feet clear of the
floor.
Figure 6 Correctly raising the cooker Figure 7 Incorrectly moving the cooker
Figure 8 Incorrectly raising the cooker
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
4

Backguard
• Before installing the cooker, assemble the backguard “C” .
• The backguard “C” can be found packed at the rear of the cooker.
• Before assembling remove any protective film/adhesive tape.
• Remove the two spacers “A” and the screw “B” from the rear of the cooktop.
• Assemble the backguard as shown and fix it by screwing the central screw “B” and the spacers “A”.
Figure 9 Assembling The Backguard
Anti-Tilt Bracket
To restrain the appliance and prevent it tipping accidentally, fit a bracket to its rear to fix it
securely to the wall.
To Fit The Anti-Tilt Bracket:
1. After you have located where the cooker is to be positioned, mark on the wall the place where the two
screws of the anti-tilt bracket have to be fitted. Please follow the indications given in Fig. 10.
2. Drill two 8 mm diameter holes in the wall and insert the plastic plugs supplied.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
5

Before drilling the holes, check that you will not damage any pipes or electrical wires.
3. Loosely attach the anti-tilt bracket with the two screws supplied.
4. Move the cooker to the wall and adjust the height of the anti-tilt bracket so that it can engage in the slot on
the cooker’s back, as shown in fig. 10.
5. Tighten the screws attaching the anti-tilt bracket.
6. Push the cooker against the wall so that the anti-tilt bracket is fully inserted in the slot on the cooker’s
back.
Figure 10 Fitting a Stability Bracket
Ventilation Requirements (GB & IE only)
• The appliance should be installed into a room or space with an air supply in accordance with BS 5440-2:2008.
• For rooms with a volume of less than 5 m3 - permanent ventilation of 100 mm2 free area will be required.
• For rooms with a volume of between 5 m3 and 10 m3 a permanent ventilation of 50 cm2 free area will be
required unless the room has a door which opens directly to the outside air in which case no permanent
ventilation is required.
• For rooms with a volume greater than 10 m3 - no permanent ventilation is required.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
6

Regardless of room size, all rooms containing the appliance must have direct access to the
outside air via an openable window or equivalent. Where there are other fuel burning
appliances in the same room, BS 5440-2:2008 should be consulted to determine the
correct amount of free area ventilation requirements.
Gas installation (GB & IE only)
This cooker uses NATURAL GAS only and cannot be used on any other gas without
modification. This appliance is manufactured for conversion to LPG if required. If the
injectors are not supplied they can be obtained from the After-Sales Service.
Installation And Service Regulations
This appliance must be installed and serviced only by a suitably qualified and registered
person, and in accordance with the current editions of the following standards and
regulations or other locally applicable regulations:
Gas Safety (Installation and Use) Regulations
Building Regulations
British Standards
Regulations for Electrical Installation
Failure to install the appliance correctly could invalidate any manufacturer’s warranty and lead to prosecution under the
above-quoted regulation.
Gas Connection
The installation of the cooker to Natural Gas or LP Gas must be carried out by a qualified gas engineer. Installers shall
take due account of the provisions of the relevant British Standards Code of Practice, the Gas Safety Regulations and
the Building Standards (Scotland) (Consolidation) Regulations issued by the Scottish Development Department.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
7

It is recommended that the gas connection to the cooker is installed with a flexible connecting tube
made to BS 5386.
Installation To Natural Gas
Installation to Natural Gas must conform to the Code of Practice, etc. The supply pressure for Natural Gas is 20 mbar.
Installation To Liquid Petroleum Gas
This appliance must only be connected to LPG after an LPG conversion kit has been fitted. The installation must
conform to the relevant British Standards.
Only a suitably qualified and registered person may convert the appliance to a different gas
type.
• When using Butane gas a supply pressure of 28 -30 mbar is required.
• When using Propane gas a supply pressure of 37 mbar is required.
• Notes: Flexible hoses can be used where the sited ambient temperature of the hose does not exceed 70°C.
These hoses must be manufactured in accordance with BS669 part 1 and be of the correct construction for the
type of gas being used.
• Gas hoses designed for natural gas MUST NOT be used for supplying LPG gas (LPG gas hoses can be
identified by a either a red band or stripe on the rubber outer coating of the hose).
• The hose should not be crushed or trapped or be in contact with sharp or abrasive edges. It should also not be
subjected to corrosion by acidic cleansing agents.
To Connect the Gas Supply:
• Fit the 1/2” BSP (female) connector (supplied with the cooker in a separate kit) to the gas inlet at the rear of the
cooker interposing the gasket. Check the correct positioning of the connector as shown and always use two
suitable spanners (Fig 11b).
• Connect the gas supply to the right or left gas inlet at the rear of the cooker. The pipe is not to cross the cooker.
• Close the unused end inlet pipe with a plug, interposing the gasket (Fig. 11a - Fig. 11b).
• To avoid damage to the appliance gas rail inlet pipe tighten the fittings using two suitable spanners (Fig. 11b).
• Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection one at a time by brushing
the solution over the connection. The presence of bubbles will indicate a leak. If there is a leak, tighten the fitting
and then recheck for leaks.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
8

Do not use a naked flame to test for leaks
Figure 11a Gas Supply Inlets
Figure 11b Connecting the Gas
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
9

Figure 12 Gas mains connection area
Replacement of Burner Injectors
If the injectors are not supplied, contact the Fisher & Paykel Authorised Service Centre. Select the injectors to be
replaced according to the “Table for the choice of the injectors”.
To Replace the Injectors
Remove pan supports and burners from the cooktop. Using a wrench substitute the nozzle injectors with those most
suitable for the kind of gas for which it is to be used. The burners are designed so that adjustment of primary air is not
required.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90LDBGFX3/Install%2F%2FUser_Guide_…
Updated: Mon, 11 May 2020 05:26:38 GMT
Powered by
10