Fisher & Paykel TITAN CE901M Service manual

INSTALLATION INFORMATION FOR TITAN (CE901 SERIES) CERAMIC COOKTOPS/HOBS
IMPORTANT INFORMATION
Please make this information available to the person
responsible for installing this cooktop as it could reduce
your installation costs.
CAUTION In order to avoid a hazard, these appliances
must be installed according to these instructions. The
appliance is to be only installed by an authorized person.
Read these instructions completely before installing or
using this product.
BEFORE YOU START
Do Ensure the countertop is square and level and ensure no
structural members interfere with space requirements.
Do Ensure a suitable disconnection switch is incorporated in the
permanent wiring, mounted and positioned to comply with
the Local Wiring Rules and Regulations.
Do Use easy to clean finishes for the wall surfaces surrounding
the cooktop/hob to aid removal of any cooking fume staining
resulting from the use of the cooktop/hob.
Do Consult local building authorities and by-laws if in doubt
regarding installation.
Do Ensure that the power cable is not accessible via
cupboard doors after installation.
Do Ensure that there is adequate clearance between the cutout
and the rear and/or side walls.
CLAMPING DOWN COOKTOP/HOB
Place the cooktop/hob into the cutout and tighten with the supplied
clamps. These will cope with bench thickness 20-50mm.
CURRENT
INFORMATION
Current Installation Instructions, Product dimensions and specifications
are available on the Fisher & Paykel web site.
www.fisherpaykel.com
Part Number 599088A Date of Issue September 2002
NEW ZEALAND, AUSTRALIA
UNITED KINGDOM (UK) & IRELAND (IE)

INSTALLATION CHECKLIST
Please check through the list provided to ensure correct installation.
Is the product earthed?
Check that the power cable is NOT touching the product.
This will ensure that the cable is not damaged by heat
from the product.
Is the product clamped down securely?
TEST THE COOKTOP OPERATES CORRECTLY
Make sure the top surface of the cooktop/hob is clear of any debris.
Wipe the glass surface clean.
urn each knob and verify that the correct element glows, and that
the indicators glow white (CE901 - red). Leave controls for one
minute before turning off. Check that the indicators change colour
when you turn the elements off. This warns that the glass surface is
still hot. These lights should turn off completely when the elements
cool down.
Encourage the user to read the User Guide - it contains important
safety information as well as tips to make the most of the new
cooktop/hob.
DIMENSIONS
BEFORE YOU CALL FOR SER ICE OR ASSISTANCE...
Check the things you can do yourself.
Refer to your User Guide and check...
1. Your product is correctly installed.
2. You are familiar with its normal operation.
If after checking these points you still need assistance, please call
your Fisher & Paykel retailer who is trained to provide information on
your product, or if we can be of any further help, please contact our
Customer Care Centre.
FOR NEW ZEALAND
P.O. Box 58732, Greenmount, Auckland.
oll Free 0800 FP CARE (0800 37 2273)
Fax [phone]
Email customer[email protected]
FOR AUSTRALIA
P.O. Box 798, Cleveland, QLD 4163.
oll Free 1300 650 590
el 07 3826 9100
Fax [phone]
Email customer[email protected]
FOR UNITED KINGDOM (UK)
Fisher & Paykel Appliances Ltd.
Broxell Close, Wedgnock Industrial Estate, Warwick,
Warwickshire, CV34 5QF.
el 01 926 626700
Fax [phone]
FOR IRELAND (IE)
C & F Quadrant, Unit L, 40 Cherry Orchard Industrial Estate, Dublin 10.
el 01 630 5757
Fax [phone]
COOKTOP/HOB CUTOUT DIMENSIONS
Minimum Depths (below coutertop/mounting surface)
CE901 75mm (body of product)
85mm (mains cable - right-hand underside, see below)
A 10mm gap is needed below the product in cases where there is a
combustible shelf.
The cooktop can be installed above a Fisher & Paykel or
Fisher & Paykel single wall oven if a 10mm (3/8”) gap is provided
between the bottom of the cooktop and the top of the
or oven.
COOKTOP/HOB DIMENSIONS
Model Width Depth Height
CE901/M 914mm 546mm 70mm
81mm (terminal block)
Power supply 8.3kW @ 235V (35.4A)
R
R
Bench thickness
15mm – 43mm
Ra ius
(5mm – 12.5mm)
524mm max / 460mm min
894mm max / 846mm
min
CUSTOMER SUPPORT
Wi th 914mm
Height 70mm
Depth 546mm
Height 81mm
at terminal block
25mm min to
front of counter