Fisher-Price Lullabye Birdies G5892 User manual

Please keep this instruction
sheet for future reference,
as it contains important
information.
Adult assembly is required.
Requires four "D" (LR20)
alkaline batteries for the
mobile and two “AA” (LR6)
alkaline batteries for the
remote control (batteries
not included).
Tool required for assembly:
Phillips screwdriver
(not included).
Lullabye Birdies™
Mobile
with Remote
Control
www.fisher-price.com
G5892
Instructions

Parts
2
Mama Bird
Crib Adapter
Base
Arm
Canopy
#6 x 5/8" Screw - 1
Shown Actual Size Remote
2
•Acrib mobile is intended for visual stimulation and is not to be grasped by a child.
•When used on a dresser top, keep out of baby’s reach.
•Always attach by all provided fasteners (clamp) tightly to a crib or playpen
according to the instructions. Check frequently.
•Do not add additional strings or straps to attach to a crib or playpen.
IMPORTANT!
•Possible entanglement injury, keep out of baby’s reach.
•Remove mobile from crib or playpen when baby begins
to push up on hands or knees.
WARNING
2 Baby Birds
Clamp
This toy contains small parts in its unassembled state.
Adult assembly is required.
CAUTION

Remote Control Features
3
Button - Press to activate the mobile once the mobile has been
turned ON. Press again to stop the mobile.
LED Signal Indicator - Lights when the button is pressed to let you
know the remote has transmitted a signal to the receiver.
Transmitter Window - Remote transmits a signal to the receiver dome
on the mobile.
Handle - Flips up so you can hang the remote on a door knob. Snaps
around bottom of the remote when not in use.
Battery Compartment - Insert two “AA” alkaline batteries. Please refer
to Battery Installation on page 4. For longer battery life, use alkaline
batteries only.
Rear View
Front View
1
1
2
3
4
5
3
4
4
5
2

Battery Installation- Remote Control
4
•Locate the battery compartment door on the back of the remote control.
•Loosen the screw in the battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
•Insert two“AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
•Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
IMPORTANT! If the mobile does not respond to the remote, it does not mean
that the battery power in the remote is low. Replace the batteries in the
remote if the LED signal indicator on the remote is dim when the
button is pressed. If the LED signal indicator does not light after installing
new batteries in the remote, check the orientation of the batteries in the
battery compartment to make sure they are properly installed.
Remote Control
Battery
Compartment

•Locate the battery compartment door on the back of the mobile base.
•Loosen the screws in the battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
Hint: If the crib adaptor is attached to the base,loosen the screws in the crib
adaptor and remove it first.
•Insert four“D” (LR20) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
•Replace the battery compartment door and tighten the screws with a
Phillips screwdriver. Do not over-tighten.
IMPORTANT! Under normal use conditions, the batteries in the mobile will
require replacement more often than the batteries in the remote.When
sounds or light become faint or movement of the mobile is sluggish, it’s time
for an adult to replace the batteries in the mobile base.
Battery Installation - Mobile Base
5
Mobile Base
Battery
Compartment

Batteries may leak fluids that can cause a chemical burn injury or ruin your
toy. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Dispose of batteries safely. Do not
dispose of batteries in a fire. The batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type, as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the toy before charging.
•If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.
Battery Safety Information
6
1,5V x 2
“AA” (LR6)
Shown Actual Size
1,5V x 4
“D” (LR20)
Shown Actual Size
+-

•Fit the arm into the slot in the base, as shown.
•Insert the #6 x 5/8" screw through the arm and into the base.Tighten the
screw with a Phillips screwdriver. Do not over-tighten.
Assembly
7
Arm
Base
• Locate the (larger) mama bird.The mama bird is marked with a .
• Find the matching on the canopy.
• Fit the plug on the mama bird into the socket in the canopy .
• "Snap" the pegs on the cover into the holes in the canopy .
• Repeat this procedure to attach the two baby birds.
Canopy
Baby Bird
1
2
#6 x 5/8" Screw
Shown Actual Size
Mama Bird
Cover

•Insert and "snap" the arm into the hole in the side of the canopy.
•Make sure the arm is fully inserted and snapped into the canopy.
When the arm is fully inserted, the red line on the arm should be
covered by the canopy.
•Pull on the canopy to be sure it is fully snapped onto the arm.
Assembly
8
Arm
Canopy
3Red Line

Crib Use
9
Battery
Compartment
Door
Crib
Adapter
Tighten
Screws
•Position the base so that the battery compartment door is facing you.
•Fit the crib adapter onto the base.
•Tighten the three screws in the crib adapter using a Phillips screwdriver.
Do not over-tighten.

Crib Use
10
•Fit the mobile base on to the crib top rail so that the threaded peg extends
outside of the crib.
•Fit the clamp onto the threaded peg and turn the clamp clockwise to
secure the base to the crib rail. Do not over-tighten the clamp.
Base
Threaded Peg
Crib Top Rail
Clamp