Fisher-Price 79011 User manual

SOOTHING SOUNDS
DELUXE BOUNCER SEAT
Model Number: 79011
Adult assembly is required.
Please save these instructions for future reference.
Tool needed for assembly: Phillips screwdriver (not included).
Requires three “C” (LR14) alkaline batteries (not included) in the soothing unit.

2
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price®Consumer Affairs,
toll-free at 1-800-432-KIDS,
between 8 AM - 5 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Affairs
636 Girard Avenue
East Aurora, New York 14052
CONSUMER INFORMATION
WARNINGS
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up unassisted.
WARNING

3
PARTS
#8 - 32 x 1/2"
Screw - 2
Shown Actual Size
Toy Bar
Mirror
Pad
3 Rings
Footrest Wire
Soothing Unit
2 Paddles
Seatback
Wire
Right Base
Wire
Left Base
Wire
Base
Connector
#8 - 32 Nut - 2
Shown Actual Size

4
BATTERY INSTALLATION
• Locate the soothing unit on the footrest wire.
• Loosen the screw in the soothing unit battery compartment door with a
Phillips screwdriver.
• Remove the battery compartment door.
• Insert three "C" (LR14) batteries, as indicated inside the battery compartment.
• Replace the battery compartment door. Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
Battery Compartment Door
1.5V x 3
“C” (LR14)
SHOWN ACTUAL SIZE
+
–
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove the exhausted batteries
from the product. Battery leakage and corrosion can damage the product. Dispose of the
batteries safely.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the “Battery Installation”
instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged under adult supervision.
• Rechargeable batteries are to be removed from the product before they are charged.
• If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclo-
sure and other parts. Do not use a damaged battery charger until it has been properly repaired.

5
• Place the base connector on a flat surface as shown.
• Position the left and right base wires as shown. Note the locations of
the colored dots on the left and right base wire.
• Fit the left base wire into the base connector.
• Fit the right base wire into the base connector.
•Make sure both colored dots on the base wires are covered by the
base connector.
1
Base
Connector
Colored Dots
Right Base
Wire
Left Base
Wire
This package contains small parts.
Adult assembly is required.
CAUTION
ASSEMBLY

3
6
ASSEMBLY
2
Base Wire
Colored
Dot
Base Wire
Soothing
Unit
Footrest
Wire
Colored
Dot
• Position the seat back wire with the toy bar sockets upright.
• Fit the seat back wire completely onto the base wires, so that each end
covers the colored dot on each base wire.
•Make sure the plastic covers on the seat back wire cover the colored
dots on the base wire.
Colored
Dot Plastic
Cover
Base
Wire
Toy Bar
Socket
Seat Back
Wire
Back View
Base
Connector
Base
Wire
• Position the footrest wire so that the soothing
unit is upright.
• While flexing the base wires toward each other,
hook the footrest wire onto the ends of the base wires.
• Push the footrest wire down completely below the colored dots on the
base wires.
• Make sure the small tabs on the left and right base wires are secure in the
base connector holes (see inset). If the small tabs are not secure in the base
connector holes, you have assembled the base incorrectly. Disassemble all
parts and refer back to Assembly step 1.

7
ASSEMBLY
• Insert a screw through the outside of each plastic cover and tighten with
a Phillips screwdriver. Do not over-tighten.
• Pull up on the seat back wire to be sure it is secure. If you can remove
either end of the seat back wire, you have not assembled it correctly.
Remove the screws, re-read and repeat Assembly steps 3 and 4.
4
#8 x 32 Nut
Pull Up
Protruding Side
Plastic
Cover
• Fit the nut (so that the protruding side is
facing the seating area) into the hexagonal
opening on the inside of each plastic cover.

8
ASSEMBLY
• Position the pad with the canopy upright.
• Fit the upper pocket on the back
of the pad onto the seat back wire .
• Lift the footrest wire. Fit the lower pocket
on the back of the pad onto the footrest
wire . Lower the footrest wire.
• Fit the restraint belts through the slots in the pad .
5
Seat Back
Wire
Slot
Pad
Restraint
Belt
A
C
C
B
C
B
A

9
ASSEMBLY
• Wrap the elastic straps on the pad
flaps around the outside of each
plastic cover.
• Hook the elastic straps to the peg on
the inside of each plastic cover.
6
Elastic
Strap
Elastic
Strap
Inside View
Elastic
Strap
Plastic
Cover
Plastic
Cover
Plastic
Cover
Peg

8
ASSEMBLY
7
• Fit the toy bar plugs into the socket in each plastic cover.
• Snap the mirror and paddles to the toy bar.
• The rings can be attached to the mirror and one of the paddles as shown.
Hint: Twist the endsof the rings apart toattach them to the mirrororpaddles.
Assembly is now complete.
• The toy bar is removable. Simply pull up to remove.
Rings
Plugs
Sockets
Toy Bar
Mirror
Paddle
10