Fisher-Price BARBIE M5727 User manual

Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tools required for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (not included).
Age: 2-5 years
Weight limit: 55 lbs (25 kg).
www.fisher-price.com
M5727

Seat
2 Fork Covers
Front Wheel Assembly
Fork
Frame
Handlebar Back
Straight Axle
2 Bushings
2 Wheel Hubs 2 Wheel Caps
#8 x 2¼" Screw - 1
Note: Some parts shown are
assembled to both sides of the trike.
Consumer Information
IMPORTANT!
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth
before assembly.
*We’ve included one extra .354" cap nut for your convenience.
Note: Tighten and loosen the screws with a Phillips
screwdriver. Do not over-tighten the screws.
4 Pedal Hubs
WARNING CAUTION
To avoid serious injury:
• Adult supervision is required.
•
Never use near cars and other motor
vehicles, near streets, steps, sloped
driveways, hills, roadways, alleys, swimming
pool areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
This product contains small parts
in its unassembled state.
Adult assembly is required.
#8 x¾" Screw - 6
2 Rear Wheels
Part not shown: Label Sheet
ALL SHOWN ACTUAL SIZE
Handlebar Front .354" Cap Nut - 2*
.354"
Parts
2

Assembly
Frame
Seat
PUSH
Wheel Hub
(Flat Side Down)
Bushing
(Grooved Side Down)
Straight Axle Assembly
Bottom View
• Place one end of the straight axle into the cap nut. Tap
the end of the straight axle with a hammer. Make sure
the cap nut is securely attached to the straight axle.
• Slide a wheel hub, flat side down, onto the straight axle.
• Slide a rear wheel, indented side down, onto the
straight axle.
• Slide a bushing, grooved side down, onto the straight axle.
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in the
rear of the frame.
• Turn the assembly upright.
• Slide a bushing, smooth side first, onto the end of the
straight axle.
• Slide a wheel, flat side first, onto the end of the straight axle.
• Slide a wheel hub, pointed end first, onto the end of the
straight axle.
• Fit the seat onto the frame.
• Push firmly near the back end of the seat to "snap" it
into place.
Straight
Axle Straight
Axle
Cap Nut
Bushing
(Smooth Side First)
Wheel Hub
(Pointed End First)
Wheel
(Flat Side First)
Straight Axle
Rear
Wheel
(Indented
Side Down)
1
3
4
2
3

Assembly
• Fit the tabs on the wheel cap into the slots in the wheel
hub. Push to "snap" the wheel cap in place.
• Repeat this procedure to attach the other wheel cap to
the other wheel hub.
• Fit two pedal hubs onto the pedal axle tabs. Make sure
the tabs fit into the slot in each pedal hub.
• While holding the pedal hubs on the pedal axle, insert the
pedal axle into the hole in the center of the front wheel.
• Press the pedal hubs into the center of the front wheel
until they are flush with the surface of the front wheel.
• Repeat this procedure on the other side with the other
two pedal hubs.
• Fit the cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel to be sure the cap nut is securely attached to
the straight axle.
Hint: You may need the help of another adult to hold the
other end of the straight axle in place.
Wheel Hub
Wheel Cap
Pedal Hub
5
7
6
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x ¾" screws into the fork cover and tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
Front Wheel
Assembly
8
Pedal Hub
Pedal Axle Tab
4

Assembly
Fork Post
Fork Cover
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
REAR OF TRIKE
• Fit the handlebar front to the fork post.
Hint: The handlebar front is designed to assemble to the
fork post one way.
• Fit the handlebar back to the fork post and handlebar
front. Hold them together firmly.
• First, insert the remaining #8 x ¾" screws through the
outer holes in the handlebar back and tighten.
• Then, insert the #8 x 2¼" screw through the center hole
in the handlebar back and tighten.
Handlebar Front
¾" Screw
¾" Screw
2¼" Screw
Handlebar Back
9
10
Fork Post
5