Fisher-Price BUTTERFLY DREAMS Mobile C0108 User manual

Please keep this
instruction sheet for
future reference, as it
contains important
information.
Adult assembly is
required.
Requires four “D”
(LR20) alkaline
batteries for the
mobile and two “AA”
(LR6) alkaline
batteries for the
remote. (Batteries
not included.)
Tool required for
battery installation:
Phillips screwdriver
(not included).
www.fisher-price.com
C0108
Butterfly Dreams™
Mobile
with Remote
Control

Parts
2
Clamp
Crib Adapter
Base
3 Butterfly
Spokes
3 Soft Toy
Spokes
3 Soft Toys
Arm
Hub
#6 x 5/8" Screw - 1
Both Shown Actual Size
#4 x 3/8" Washer
Head Screw - 3
Remote
2
•Acrib mobile is intended for visual stimulation and is not to be grasped by a child.
•When used on a dresser top, keep out of baby’s reach.
•Always attach by all provided fasteners (clamp) tightly to a crib or playpen
according to the instructions. Check frequently.
•Do not add additional strings or straps to attach to a crib or playpen.
IMPORTANT!
•Possible entanglement injury, keep out of baby’s reach.
•Remove mobile from crib or playpen when baby begins
to push up on hands or knees.
WARNING
This toy contains small parts in its unassembled state.
Adult assembly is required.
CAUTION

Light Dome – Projects butterflies and leaves onto baby’s ceiling.
Start Button – Starts or restarts music and soothing lights.
Light Select Button – Choose dome light, night light, both lights
or no lights.
Song Select Button – Press to choose from six different songs.
Power/Volume Switch - Choose high volume , low volume ,
no sound or power off .
Receiver Dome – Accepts signal from the remote. Dome needs to be
turned so it aligns with the transmitter window on the remote.
Night Light – Features softly glowing colors.
Mobile Features
3
1
2
3
4
5
6
7
1
2
3
4
5
6
7

Remote Features
4
Button - Press to activate the mobile once the mobile has been
turned ON. Press again to stop the mobile.
LED Signal Indicator - Lights when the button is pressed to let you
know the remote has transmitted a signal to the transmitter.
Transmitter Window - Remote transmits a signal to the receiver dome
on the mobile.
Handle - Flips up so you can hang the remote on a door knob. Snaps
around bottom of the remote when not in use.
Battery Compartment - Insert two “AA” alkaline batteries. Please refer
to Battery Installation on page 5. For longer battery life, use alkaline
batteries only.
Rear View
Front View
1
1
2
3
4
5
3
4
4
5
2

Mobile Base
•Locate the battery compart-
ment door on the back of the
mobile base.
•Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
Hint: If the crib adaptor is attached to
the base, loosen the screws in the crib
adaptor and remove it first.
•Insert four “D” (LR20) alkaline
batteries.
Hint: We recommend using alkaline
batteries for longer battery life.
•Replace the battery compart-
ment door and tighten the screws
with a Phillips screwdriver. Do not
over-tighten.
IMPORTANT! Under normal use
conditions, the batteries in the mobile
will require replacement more often
than the batteries in the remote.
When sounds or light become faint or
movement of the mobile is sluggish,
it’s time for an adult to replace the
batteries in the mobile base.
Remote
•Locate the battery compartment
door on the back of the remote.
•Loosen the screw in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
•Insert two “AA” (LR6) alkaline
batteries.
Hint: We recommend using alkaline
batteries for longer battery life.
•Replace the battery compart-
ment door and tighten the screw
with a Phillips screwdriver. Do not
over-tighten.
IMPORTANT! If the mobile does not
respond to the remote, it does not
mean that the battery power in the
remote is low. Replace the batteries in
the remote if the LED signal indicator
on the remote is dim when the
button is pressed. If the LED signal
indicator does not light after installing
new batteries in the remote, check the
orientation of the batteries in the
battery compartment to make sure
they are properly installed.
Battery Installation
5
Mobile Base Remote
Battery
Compartment
Battery
Compartment

Batteries may leak fluids that can cause a chemical burn injury or ruin your
toy. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Dispose of batteries safely. Do not
dispose of batteries in a fire. The batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type, as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the toy before charging.
•If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.
Battery Safety Information
6
1,5V x 2
“AA” (LR6)
Shown Actual Size
1,5V x 4
“D” (LR20)
Shown Actual Size
+-

•Locate the three butterfly spokes.
•Insert and “snap” the tabs on the ends of the butterfly spokes into the
slots in the hub, as shown.
Assembly
7
Butterfly Spoke
Tab
Slot
Hub
•Locate the three soft toy spokes.
•Place the end of the spoke with the larger hole onto the matching hole on
the hub, as shown.
•Insert a #4 x 3/8" screw through the spoke and into the hub. Tighten the
screw with a Phillips screwdriver. Do not over-tighten.
•Repeat this procedure to attach the other two soft toy spokes.
Soft Toy Spoke
Hub
#4 x 3/8" Washer
Head Screw
Shown Actual Size
1
2

•Insert and “snap” the arm into the hole in the side of the hub.
•Fit the arm into the slot in the base, as shown.
•Insert the #6 x 5/8" screw through the arm and into the base.Tighten the
screw with a Phillips screwdriver. Do not over-tighten.
Base
#6 x 5/8" Screw
Shown Actual Size
Arm
Hub Arm
•Fit a soft toy string through the slot in the end of a soft toy spoke.
•Pull down gently on the soft toy to secure the string in the soft toy spoke.
•Repeat this procedure to attach the remaining soft toys to the other two
soft toy spokes.
Assembly
8
Soft Toy Spoke
Soft Toy String Soft Toy String
Slot
3
4

Crib Use
9
Battery
Compartment
Door
Crib
Adapter
Tighten
Screws
•Position the base so that the battery compartment door is facing you.
•Fit the crib adapter onto the base.
•Tighten the three screws in the crib adapter using a Phillips screwdriver.
Do not over-tighten.

Crib Use
10
•Fit the mobile base on to the crib top rail so that the threaded peg extends
outside of the crib.
•Fit the clamp onto the threaded peg and turn the clamp clockwise to
secure the base to the crib rail. Do not over-tighten the clamp.
Base
Threaded Peg
Crib Top Rail
Clamp