Fisher-Price CGK05 User manual

fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three AAA (LR03) alkaline batteries (not included) for operation.
Battery installation is required.
Adult assembly is required. Tool required: Phillips screwdriver (not included).
CGK05

2
Consumer Information
PRINTED IN CHINA CGK05pr-0920
©Disney
©2014 Mattel. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, except as noted.
Care
• Wipe this toy with a clean, damp cloth. Do not immerse.
• This toy has no consumer serviceable parts. Do not take apart.
CO
N
SU
MER A
SS
I
S
TAN
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.

3
Battery Installation
• Loosen the screw in the battery compartment door with a Phillips screwdriver and
remove the door.
• Insert three AAA (LR03) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw. Do not over-tighten.
• If this toy begins to operate erratically, you may need to reset the electronics. Slide the
power/volume switch off and then back on.
• When sounds become faint or stop, it’s time for an adult to change the batteries.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities.
1,5V x 3
AAA (LR03)

4
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.

5
Assembled Parts
This package contains small parts. For adult assembly only.
CAUTION
Balcony
Clock Tower
Short Tower
Base
Tall Tower
2 Flags
Floor
Wall
Part not shown: Label Sheet
3 mm x 15 mm Screw – 7
Shown Actual Size
Tighten and loosen all screws with
a Phillips screwdriver. Do not over-tighten.
3 mm x 15 mm Washer Head Screw – 2

6
Assembly
• Fit the pegs on the tall tower into the openings in the wall.
Tall Tower
Wall
1
• Carefully lay the wall assembly on a flat surface with the inside facing up.
• Slide the tab on front edge of the clock tower assembly into the groove in the wall assembly
A
.
• Fit the peg on the side of the clock tower assembly onto the post on the tall tower B.
SIDE VIEW
Peg Clock Tower
Assembly Tab
Wall Assembly
BA
4

7
• Fit the pegs on the short tower into the openings in the wall.
Short Tower
2
Assembly
Screw
• Align the hole in the clock tower assembly with the post on the wall assembly. Insert
a 3 mm x 15 mm screw into the post. Tighten the screw.
5

8
• Fit the tabs on the clock tower into the slots in the floor. Push to “snap” in place.
3
Assembly
Floor Slots
Clock Tower Tabs
Fl
Screws
• Insert two 3 mm x 15 mm screws into the holes in the clock tower and tighten.
6

9
• Insert two 3 mm x 15 mm screws into the balcony and tighten.
Screws
Assembly
10
• Align the slots in the clock tower assembly with the holes in the posts in the wall
assembly. Insert two 3 mm x 15 mm washer head screws and tighten.
2 Washer Head
Screws
7

10
• Fit the tabs on the wall assembly into the slots on the base. Push to “snap” in place.
• Insert two 3 mm x 15 mm screws into the wall assembly and tighten.
Base
Screws
Assembly
8
11