Fisher-Price DJD09 User manual

DJD09
DJD10
fisher-price.com
Keep this instruction sheet for future reference,
as it contains important information.
Requires three AA (LR6) alkaline batteries (not included) for operation.
Adult assembly is required.
Tool required: Phillips screwdriver (not included).
Wipe this toy with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.
Actual product may appear different from the photos shown.

2
Consumer Information
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the
equipment and receiver.
•Consult the dealer or an experienced
radio/TV technician for help.
NOTE: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) il doit pouvoir tolérer tout brouillage
radioélectrique reçu, même si ce brouillage
est susceptible de compromettre son
fonctionnement.
CONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.

3
Assembled Parts
2 Rear Fenders Rear Wheel Base Windshield
Side Base
Side Panel
(outside)
Dash Trunk
Side Panel
(inside)
Seat Back
Door
Front End
Part not shown: Label Sheet
#8 x ¾" (1,9 cm) Screw – 21
SHOWN ACTUAL SIZE
Tighten all screws with a Phillips
screwdriver. Do not over-tighten.
This package contains small
parts. For adult assembly only.
CAUTION

4
Assembly
1
2
•Fit the rear fenders onto the rear wheel base. Push to “snap” each rear fender in place.
Hint: Each rear fender is designed to fit one way. If it does not seem to fit, try the other
rear fender.
Rear
Fenders
Rear Wheel Base
•Fit the trunk into the slots in the rear wheel base. Push to “snap” into place.
Trunk

5
3
4
•Fit the tabs on the seat back into the slots in the trunk.
•Insert two screws into the seat back and tighten.
•Fit the side panels onto the front and rear ends.
Seat Back
Side Panel
(outside)
Side Panel
(inside)
Front End
Assembly
Rear End

6
Assembly
5
6
•Insert nine screws into the side panel and tighten.
•Carefully turn the car assembly over.
•Fit the side base to the front and rear end of the car assembly.
Side Base
BOTTOM VIEW
©2015 Mattel. All Rights Reserved.
PRINTED IN MEXICO
DJD09-0970
1100695189-DOM

7
•Turn the car assembly upright.
•Fit the peg on the door into the hole in the car. Push to “snap” in place.
Door Peg
•Insert six screws into the side base and tighten.
7
8
Assembly

8
IMPORTANT! Apply labels 7 and 8 to windshield before completing the next step.
•Apply labels exactly as shown in the illustration. Avoid repositioning a label after it has
been applied.
•Fit the windshield onto the dash and push to “snap” in place.
9
10
11
•Fit the windshield on the dash into the slot in the front end.
8 7
Windshield
Dash
Assembly

9
9 3 4
•Carefully turn the car assembly over.
•Insert four screws into front end and tighten.
BOTTOM VIEW
12
12
6
Decoration
Apply labels exactly as shown in illustrations.
Avoid repositioning a label after it has been applied.
FRONT VIEW
Assembly

10
5 10
9 3 4
Decoration
LEFT SIDE VIEW
RIGHT SIDE VIEW