Fisher-Price J8999 User manual

Please keep this instruction sheet for future reference, as it contains important information.
Requires three "AA" (LR6) alkaline batteries (not included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
www.fisher-price.com/uk
J8999
Instructions

2
Parts
CAUTION
This product contains small parts in its unassembled
state. Adult assembly is required.
Parts Not Shown:
Label Sheet
Car
Tow Truck
2 Figures
#6 x 1,3 cm (½") Screw - 8
Shown Actual Size
Garage Base
Ramp
Tool Chest
Gate
Lift Handle
Lower Track
News Stand
Post
Lift Roof Track Support
Upper Track
VacuumLift
2 Fences
Note: Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
© 2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA J8999pr-0726

• "Snap" the tabs on the lower track into the slots in the base.
Lower Track
4
3
Assembly
• Position the lift on a flat surface. Note the locations of the bot-
tom slots and the upper tabs on the lift.
• Hold the base at an angle. While making sure the upper tabs
on the lift fit into the grooves in the base , insert the tabs on
the base into the bottom slots on the lift .
• Press down on the base to "snap" the lift in place.
1
2
• Fit the lift roof on the lift.
• Insert four
#6 x 1,3 cm
(½") screws into the lift roof and tighten.
Lift Roof
Bottom Slots
Upper Tabs Base Grooves
Tabs


• Turn the garage on its side on a flat surface, as shown.
• Fit the connectors on the end of the ramp into the holes on
the top of the base. Be sure to fit the hooked tab on the side
of the lift into the slot on the ramp. Press the ramp until it
"snaps" in place.
• Turn the garage upright again.
Hooked Tab
Slot
3
Ramp

Assembly
• Press the clamp on the track support onto the base column.
• Rotate the track support so that the holes in the support fit
over the pegs on the lower track.
Track Support
Clamp
Column
5
Pegs Through Holes
• Turn the garage on its side on a flat surface, as shown.
• "Snap" the rectangular connectors on the upper track into the
holes at the top of the base.
• Fit the other end of the upper track over the end of the lower
track.
• Turn the garage upright again.
• Insert two 1,3 cm (½") screws into the holes on the underside
of the upper track, as shown. Tighten the screws.
• Turn the garage upright again.
Upper Track
6
4

Assembly
• To attach the post,
turn the garage over
so the bottom is facing you.
• Align the holes in the post with the pegs, as shown.
• Insert two 1,3 cm (½") screws into the post and tighten.
• Turn the garage upright.
Post
Pegs
Bottom View
• "Snap" the gate into the slots on the top of the garage.
Gate
10
9
• Tip the lift handle and fit the hooked tab through the channel
in the side of the lift .
• Slide the lift handle down and "snap" the tab on the handle
into the slot in the lift .
Hooked Tab
Channel
Slot
7
Lift Handle

• "Snap" the news stand into the top side of the base.
News Stand
8

5

6
Battery Installation
• Locate the battery compartment on the top level of
the garage.
• Loosen the screw in the battery compartment door.
Remove the battery compartment door.
• Insert three "AA" (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screw.
• Protect the environment by not disposing of this product
with household waste (2002/96/EC).
C heck your local authority for recycling advice and
facilities (Europe only).
Battery
Compartment
Door
1.5V x 3
“AA” (LR6)
Shown Actual Size
• "Snap" the tool chest into the base.
12
Vacuum
• "Snap" the vacuum into the base.
11
Assembly

Decoration
• Before applying labels, wipe the surface of the toy with a clean, dry cloth to remove
dust or oils.
• For best results, avoid repositioning a label once it has been applied.
• Apply labels as shown in the illustration.
4
6
9
1
Fun sounds all around the garage!
Press these buttons around the
garage to hear many fun sound
effects.
Telephone
Gas Pump
Track Entrance
• Locate the On/Off switch under the
battery compartment.
• Slide the switch to • to turn the toy
on and to the o to turn it off.
On/Off Switch
o•
7
7
2
8
5
10
3
11

In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid battery
leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable (nickel-
cadmium).
• I nsert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.
Always remove exhausted batteries from the product. Dispose
of batteries safely. Do not dispose of this product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
Consumer Information
Care
GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked
Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory
Service 1300 135 312.
NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331,
Auckland.
ASIA: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Battery Safety Information
• Wipe the toy with a clean cloth dampened with a mild soap
and water solution.
• Do not immerse the toy.
• This toy has no consumer serviceable parts. Do not take this
toy apart.