Fisher-Price K3799 User manual

K3799
• Please keep this instruction sheet for future reference,
as it contains important information.
• Requires three "D" (LR20) alkaline batteries for the
mobile and two "AA" (LR6) alkaline batteries for the
remote (batteries not included).
• Adult assembly required.
• Tool required for assembly: Phillips screwdriver
(not included).

2
WARNING
Prevent Entanglement Injury
• Keep mobile out of baby's reach
• Remove mobile portion of product from crib or playpen when baby
begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add additional
strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib or playpen.
IMPORTANT! Always attach with all provided fasteners tightly to a crib or
playpen according to the instructions. Do not add additional strings or straps
to attach to a crib. Check frequently. The mobile portion of this product may be
used from birth until 5 months. The base portion of this product may be used
from birth until 24 months. A crib mobile is intended for visual stimulation and
is not to be grasped by a child.
Consumer Information
Care
• Wipe this toy with a clean cloth dampened with a mild soap and water solution.
Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take this toy apart.
• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted
batteries from the product. Dispose of batteries safely. Do not dispose of this
product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.

3
Remote 3 Leaves
3 Soft Toys
Clamp
Base
Arm
Crib
Adaptor
Mobile Hub
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws.
Tighten and loosen all screws with a Phillips screwdriver. Do not overtighten.
Parts

4
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
• Loosen the screws in mobile base battery compartment door with Phillips
screwdriver and remove the door.
Hint: If the crib adaptor is attached to the base, loosen the screws in the crib
adaptor and remove it first.
• Insert three "D" (LR20) alkaline batteries.
• Loosen the screw in the remote battery compartment door with a Phillips
screwdriver and remove the door.
• Insert two "AA" (LR6) alkaline batteries.
• Replace each battery compartment door and tighten the screws.
IMPORTANT! Under normal use conditions, the batteries in the base will require
replacement more often than the batteries in the remote. When sounds or light
become faint or movement of the mobile is sluggish, it's time for an adult to
replace the batteries in the base.
©2012 Mattel. All Rights Reserved.
PRINTED IN CHINA K3799b-0920
1,5V x 3
“D” (LR20)
1,5V x 2
“AA” (LR6)
IMPORTANT! If the mobile does not respond to the remote, it does not mean that
the battery power in the remote is low. Replace the batteries in the remote if the
LED signal indicator on the remote is dim when the button is pressed. If the LED
signal indicator does not light after installing new batteries in the remote, check
the orientation of the batteries in the battery compartment to make sure they are
properly installed.
Mobile Base Remote

5
Assembly
Crib Adaptor
• Fit the crib adaptor to the base.
• Tighten the four screws in the crib adaptor.
• First press the button next to the socket and then slide the socket
door open .
• Fit the arm into the socket in the base.
• Tighten both screws in the arm.
Arm
Base
Base
 PRESS
Socket

SLIDE
1
2

6
3
• Fit the mobile hub onto the end of the arm.
• Tighten both screws in the arm to secure the mobile hub.
Hint: You may want to attach the soft toys to the mobile hub before assembling
the arm to the mobile hub. Please refer to assembly step 5 for instructions to
assemble the soft toys.
Mobile Hub
Assembly

7
• “Snap” the leaves into the slots in the mobile hub.
Leaves
• Fit the soft toys to the pegs on the underside of the mobile hub.
• Tighten the screw in each toy to secure each to the mobile hub.
Soft Toys
Assembly
4
5

8
Crib Attachment
Base Crib Top Rail
Clamp
• Fit the base onto the crib top rail, so that the threaded peg extends
outside the crib.
• Fit the clamp onto the threaded peg and turn the clamp clockwise to
secure the base to the crib.
• Do not over-tighten the clamp.
Mattress
Bottom of Base
At least 7 inches
• If the distance between the bottom of the base and the mattress is less than
7 inches (18 cm), lower the crib mattress.

9
Remote Use
• Press the button on the remote to activate music, lights and motion.
• Press again to stop.
• In the unlikely event that use of the remote interferes with normal use
of other remote controlled equiment, such as televisions or stereos, or use of
other electronic or battery powered appliances interfere with operation of the
mobile, do not use both at the same time.
• You may notice a loss of range between the remote and the mobile when using
in bright light. For best performance, avoid using the remote in areas of bright
light. Move the mobile, or reduce the amount of light to improve performance.
• Position the mobile so that the receiver arrow points towards the area that the
remote will be used. Make sure there is a clear path between the remote and
the mobile. Point the end of the remote toward the mobile receiver and
press the button.
Note: The remote will remain active for about one hour. When the LED goes out,
you will need to slide the power/volume switch on the mobile off, then on again
to reactivate.

10
Classical Music, Rainforest Sounds,
Lights and Motion
Power/Volume Switch
Power/Volume Switch
Choose from three settings:
ON with low volume
ON with higher volume
OFF
Lights and M
Lights and M
otion Select Switch
otion Select Switch
Lights and Music
Lights, Music and Motion
Motion and Music
Music and Sound Select Buttons
Music and Sound Select Buttons
Choose classical music from Bach,
Beethoven and Mozart or soothing
sounds of the Rainforest.