Fisher-Price M7332 User manual

www.fisher-price.com
M7332

2
• Please keep this instruction sheet for future reference, as it
contains important information.
• Adult assembly is required.
• Tools needed for assembly: Hammer, Phillips Screwdriver
and Scrap Block of Wood (not included).
• Age: 2 - 6 years; Weight Limit: 60 lbs (27 kg).
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth before assembly.
WARNING
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor
vehicles, near streets, steps, sloped drive-
ways, hills, roadways, alleys, swimming pool
areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
Consumer Information
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. PRINTED IN MEXICO
© 2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. M7332pr-0920
#8 x 3" Screw – 1
#8 x 3/4" Screw – 4
FASTENERS SHOWN ACTUAL SIZE
Cap Nut
This product contains small parts in its
unassembled state. Adult assembly is required.
CAUTION

3
Parts
Note: Some parts shown are assembled to both sides of the trike.
Handlebar
Front Wheel
4 Pedal Hubs
Pedal Axle
2 Pedals
Fork
2 Fork Covers
Frame
Seat
Seat Retainer
Rear Wheel
Straight Axle
2 Hubcaps
Cap
Part Not Shown: Label Sheet
Cap Nut
Cap Nut Assembly Tool
2 Covers

4
Assembly
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
Rear Wheel
Indented Side Down
• Place a scrap block of wood on a flat surface.
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely attached
to the straight axle.
• Dispose of the cap nut assembly tool properly.
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to "snap" the cover in place. Repeat this procedure
to attach the other cover to the other hubcap.
• Set the frame assembly aside.
Cap Nut
Rear Wheel
Indented Side Up
Cap Nut
Assembly Tool
Assembled
Rear Wheel
Straight Axle
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Hole Hole
Frame
Straight Axle
BOTTOM VIEW
Hubcap
Hubcap
Frame
Straight Axle
1
2
3
Cover
Hubcap

5
Assembly
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
Pedal Hub
Pedal Hub
Pedal Axle
Tab
Tab
Slot
• While holding the pedal
hubs on the pedal axle,
insert the pedal axle through the hole in the center of the
front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
Hole
Pedal Axle
Pedal Hubs
Front Wheel
• Place a scrap block of wood under the front wheel assembly
with the exposed end up.
• Fit a pedal on the pedal axle.
• Tap the pedal with a hammer until it is secure.
Pedal Axle
Front Wheel Assembly
Pedal
Pedal Hub
Pedal Hub Pedal Axle
• Turn the front wheel
assembly over.
• Insert a pedal hub onto the top of the pedal axle and into
the hole in the center of the front wheel.
• Insert the remaining pedal hub below the pedal axle and
into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
4
5
6
7

6
Assembly
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Hint: You may need to rotate the handlebar to align
the holes.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
Handlebar
Frame Neck
Fork Post
Fork Cover
Rear of Trike
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws through the fork cover and into
the fork arm. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
• Insert and “snap” the cap into the hole in the frame.
Cap
Seat Retainer
Seat
Peg
Holes
8
9
10
11

7
• At an angle, insert the tabs on the seat into any of the top
three sets of slots for the lower, middle or upper position.
• Lower the seat so that the seat retainer inserts and snaps
into the slots in the frame.
• Pull up on the seat to be sure it is secure.
Seat
Helpful Hint: The seat can be attached to the frame in any of
three positions, depending on the size of your child. Check
your child’s fit on the trike by observing the seat to pedal
distance, as it is being ridden. If the pedals seem too far
away or too close for your child, move the seat up or down.
Attaching the Seat
• Make sure the areas where the labels will be applied are
clean and dry. Wipe your vehicle with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustration above.
One-time assembly is now complete.
Label Decoration
Lower Position Middle Position Upper Position
Tabs
Slots
Seat
Retainer
1
2
6
7
7
IMPORTANT! It is a good practice to start training children
very young regarding the importance of helmet use. When
children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time
they ride. For this reason, even while riding a tricycle, it is
a good idea to familiarize your child with helmet use, so that
it becomes a habit for life. Choose a helmet that complies
with requirements of the applicable certifying agency for
bicycle helmets.
(Label 5on other side)
4
3

8
• Periodically, check the plastic parts and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• To clean, use a mild soap and water solution and a clean
cloth. Rinse clean with water to remove soap residue.
Seat Retainer Tab
• Turn the frame on it’s side.
• Squeeze the seat retainer tabs toward one another and lift
the seat from the frame.
CareRemoving the Seat
Seat Retainer Tab
Frame
Seat