Fisher-Price M9523 User manual

7
M9523
BLR87
Please keep this instruction sheet for future reference, as it
contains important information.
Requires three LR44 button cell alkaline batteries (included)
for bear toy operation.
Adult assembly is required.
Tool needed for assembly: Phillips screwdriver (not included).
FOR DOLL ONLY. NOT INTENDED FOR CHILD USE.
Doll sold separately.
fisher-price.com

2
Assembled Parts
Both Shown Actual Size
Note: Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten.
• Fit the front brace onto one of the frames.
Hint: The front brace will only fit on the frame one way. If it
does not seem to fit, turn it around and try again!
• Insert two M3,5 x 15mm screws into the holes in the frame
and tighten.
This package contains small parts. For adult
assembly only.
Seat
Back BraceFront Brace
Support Bar
Tray
2 Frames
Front Brace
Frame
M3,5 x 15mm
Screw - 8
M4,5 x 18mm
Washer Head Screw - 4
BACK VIEW
• Turn the seat face down. Insert two M3,5 x 15mm screws into
the seat and tighten.
CAUTION
1
6

3
• Fit the other frame onto the braces.
• Insert three M3,5 x 15mm screws into the holes in the frame
and tighten.
• Fit the back brace onto the same frame.
Hint: The back brace will only fit on the frame one way. If it
does not seem to fit, turn it around and try again!
• Insert an M3,5 x 15mm screw into the hole in the frame
and tighten.
Back Brace
Frame
Assembly
• Fit the seat onto the frame assembly. Push down on the seat
to fit in place.
Frame
Assembly
Seat
• While holding the seat in place, turn the assembly face down.
• Insert two M4,5 x 18mm washer head screws into the holes in
the back of the seat, as shown.
• Tighten the screws.
SIDE VIEW BOTTOM VIEW
7 8
2 3

4
IMPORTANT! This step must be completed before attaching
the seat to the frame assembly.
• "Snap" the support bar onto the pegs on the top of the
frame assembly.
Support Bar
Frame Assembly
• "Snap" the tray handles into the holes in the seat.
Tray
• Insert two M4,5 x 18mm washer head screws into the holes
on the bottom of the seat, as shown.
• Tighten the screws.
• "Snap" the bear toy into the slot in the seat.
Seat
9
4 5
10

5
United States Only
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void
the user’s authority to operate the equipment. This device
complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
ICES-003
This Class B digital apparatus complies with Canadian
ICES-003. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada. L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique reçu, meme si ce
brouillage est susceptible de compromettre le fonctionnement
du dispositif.
Battery Replacement
• Locate the battery compartment on the back of the bear.
• Loosen the screw in the battery compartment door with a
Phillips screwdriver screwdriver and remove it.
• Replace the batteries with three, new LR44 button cell
alkaline batteries.
• Replace the battery compartment door and tighten the screw.
• If this toy begins to operate erratically, you may need to reset
the electronics. Remove the batteries and reinstall.
• When sounds become faint or stop, it’s time for an adult to
change the batteries!
1,5V x 3
LR44 or Equivalent
FCC Statement
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
Battery Safety Information

6
Sit 'n Play
Press the button
on the bear
for musical tunes.
Sturdy Walker
©2013 Mattel. All Rights Reserved.
PRINTED IN CHINA M9523d-0920
• Protect the environment by not disposing of this
product with household waste (2002/96/EC). Check
your local authority for recycling advice and facilities.
Care
• Wipe with a clean cloth dampened with a mild soap and water
solution. Do not immerse this toy.
C
ONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.