Fisher-Price R8931 User manual

R8931
R8931R8931
www.fisher-price.com
Product features and decoration may vary from the photograph above.

CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
2
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO R8931a-0920
Consumer Information
• This toy includes an inflatable ball. If the ball becomes soft,
inflate it with a standard, hand-operated air pump with a
standard air needle (both not included).
• The ball will contain the correct amount of air when its
circumference measures 21 to 22 inches. Measure the
circumference of the ball with a tape measure or with a piece
of string cut 21 to 22 inches long. Do not over-inflate the ball.
Care
• To clean, use a mild soap and water solution and clean cloth.
Rinse clean with warm water to remove soap residue.
• Be sure to drain water from the base before extended
storage. If water freezes in the base, it could cause damage.
• Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• Check plastic parts regularly and if broken or cracked,
dispose of them properly.
• Please keep this instruction sheet for future reference, as it
contains important information.
• Adult assembly is required.
• Tool required for assembly: Phillips Screwdriver
(not included).
• Water or sand to fill base (not included).
IMPORTANT! Rim height should be adjusted only by an adult.

3
Backboard
Lower PostUpper Post
Assembled Parts
Hint: Some parts were placed inside the lower post for shipping.
Note: Label sheet not shown.
Base
Rim Assembly
SHOWN ACTUAL SIZE
Note: Tighten all screws with a Phillips
screwdriver. Do not over-tighten the screws.
#8 x 3/4" Screw - 4
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION

2
3
4
4
• Carefully peel a label from the label sheet and apply it to
the backboard, as shown.
• Smooth out the label to remove any air bubbles.
• Repeat this procedure to apply the remaining labels to
the backboard.
Hint: The labels are designed to overlap.
Assembly
1
5
2
3
4
Lower Post
Base
• Insert and "snap" the lower post into the base.
• Pull up on the post to be sure it is secure in the base.
Latch
• Fit the rim assembly to the backboard as shown.
• Insert four screws into the holes on the back of the
backboard. Tighten the screws.
• Flip down the latch on the lower post.
• Insert the upper post into the lower post.
Lower Post
Upper Post
Rim Assembly
Backboard
BACK VIEW
1

5
5
Assembly Setup
Plug
• After assembly is complete, fill each base with water or
approximately 20 lbs of sand (water or sand not included) to
keep this product stationary.
• Simply lift the plug, fill the base and then replace the plug.
• Slide the backboard onto the post until it "snaps" into place.
• Pull up on the backboard to be sure it is secure on the post.

Upper Post
Grooves
Lower Post
Latch
6
IMPORTANT! Rim height should only be adjusted by an adult.
Also, make sure children are not standing below the rim when
adjusting the rim height.
Adjusting Rim Height
• To lower the rim height: While holding the upper post, flip
the latch on the lower post down. Lower the upper post and
flip the latch into the grooves to secure in place.
• To raise the rim height: Simply lift the upper post and flip
the latch into the grooves to secure in place.
• After adjusting the rim height, gently push down on the
backboard to be sure it is secure.
Adjusting Rim Size
• Make the rim larger for beginners or smaller for "pros"! Turn
the knob on the rim counter-clockwise for a smaller rim;
clockwise for a larger rim.
TOP VIEW