Fisher-Price SHAKE 'N GO! XTREME SPEEDWAY User manual

1
1
1
1
www.fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Requires four “D” (LR20) alkaline batteries (not included) for the charger.
Tool required for battery installation: Phillips screwdriver (not included).
TM

2
Care
• Wipe this toy with a clean cloth, dampened with a mild soap and
water solution. Do not immerse the cars or charger.
• This product has no consumer serviceable parts. Do not take this
toy apart.
Battery Removal
• Before disposing of the cars, please remove the batteries.
• Loosen the screws in the bottom of each car.
• Remove the battery from each car and dispose of it properly.
Consumer Information
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
ICES-003
• This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
NMB-003
• Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur
du dispositif doit être prêt à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. P4447a-0920
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO

3
Assembled Parts
Straight Track – 4
Large Curved Track – 4
Crossover Track
Upper Loop Track – 2
Lower Loop Track – 2
Lower Loop Support – 2
Upper Loop Support – 2
Wavy Track
Small Curved Track – 4
• Locate the battery compartment door under the car charger.
• Loosen the screws in the battery compartment door and remove
the door.
• Insert four “D” (LR20) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws.
• If the charger begins to operate erratically, you may need to reset
the electronics. Remove the batteries and replace.
• When the indicator lights do not turn on, it’s time for an adult to
change the batteries in the charger.
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your toy. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Dispose of batteries safely.
Do not dispose of the product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• If you use rechargeable batteries in the charger, remove them
from the charger before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Battery Installation
Battery Safety Information
+-
1.5V x 4
"D" (LR20)

4
• Turn a lower loop track over.
• Fit a lower loop support into the socket on the lower loop track.
Hint: The lower loop support only fits one way. If it does not seem
to fit, turn it around and try again!
• Repeat this procedure to assemble the other lower loop support
to the other lower loop track.
Easy Track Setup
• "Snap" the track pieces together.
1
6
Lower Loop Support
Socket
Lower Loop Track
Upper Loop Support Upper Loop Support
Upper Loop Track
Lower Loop Track Assembly
• Turn the lower loop assemblies upright.
• "Snap" an upper loop track onto the end of a lower loop track assembly.
• Repeat this procedure to assemble the other upper loop track to
the other lower loop track assembly.
2
• Slide upper loop supports onto each side of the upper loop.
4
• Push to fit the inside edges of the lower loop together.
5
Hint: For some assemblies, you can hook the upper portion of the
track together, side by side.
7
• Place the loop assemblies next to each other to align the top edge.
3

5
Extreme Speed. Extreme Action. Extreme Fun!
Charge the Cars!
• Fit a car onto the charger.
Hint: The car only fits on the charger one way. If it does not seem
to fit, turn it around and try again.
• A yellow indicator light turns on when the car is charging. Each car
takes approximately 45 minutes to fully charge. When charging
is complete, the green indicator light turns on.
• When movement becomes slow or stops, it’s time to charge
the cars!
Pit Stop Guide
• The cars only fit on the charger one way. Make sure the car is
placed on the charger properly to ensure a complete charge.
• The yellow light means the car is charging. The green light turns
on when the charge is complete. If you see the green light as
soon as you put the car on the charger, remove the car and
replace it on the charger.
• If you are having difficulty connecting all the track pieces,
try building three larger sections and fitting them together.
Indicator Lights

6
Shake It, Then Race It!
• Set each car down on the track then let it go!
3
• Slide the power switch on the bottom of each vehicle ON .
1
• Put the ramps on the track to watch the cars “jump” the track!
4
• Setup the barrels for crash-up action.
5
• Lift the car and shake it to start the "engine" and the sound effects.
Hint: For maximum distance, shake the car 7 or 8 times. Shaking
more than this does not increase the distance it will travel.
2
• Watch the cars loop the loop!
• When finished playing with this toy, slide the power switch on
each car OFF .
6

7
Easy Track Changeup!
Try these fun track layouts!

8
Easy Track Changeup!
Try these fun track layouts!