Fisher-Price V3254 User manual

www.fisher-price.com
V3254
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “AA” (LR6) alkaline batteries for operation (not included).
Adult assembly is required. Tool required for assembly:
Phillips screwdriver (not included).

2
Assembled Parts
2 Bases
Handle
Activity Panel
Handle
Retainer
#8 x ¾" Screw – 8
Tighten or loosen all screws
with a Phillips screwdriver. Do
not over-tighten the screws.
Shown Actual Size
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.

3
Battery
Installation
• Locate the battery compartment on the
back of the toy.
• Loosen the screws in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert three “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline
batteries for longer battery life.
• Replace the battery compartment door
and tighten the screws with
a Phillips screwdriver.
• If the toy begins to operate erratically
you may need to reset the electronics.
Slide the power/volume switch off and
then back on.
• When sounds from this toy become faint
or stop, it’s time for an adult to change
the batteries.
In exceptional circumstances, batteries
may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose of
batteries safely. Do not dispose of this
product in a fire. The batteries inside
may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the
product before charging.
• If removable, rechargeable batteries are
used, they are only to be charged under
adult supervision.
Battery Safety
Information
1,5V x 3
“AA” (LR6)
• Protect the environment by not
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities
(Europe only).

4
Assembly
• At an angle, fit the handle to the activity
panel. Rotate the handle down to fit the
holes in the handle to the pegs on the
activity panel.
• Place the handle retainer on top of
the handle.
• Insert four screws into the handle
retainer and tighten.
Activity Panel
4 Screws
Handle
Retainer
1
2
• Fit the activity panel into each base.
Hint: The activity panel will only fit in each
base one way. If it does not seem to fit,
turn it around and try again!
• Carefully turn the assembly over.
• Insert two screws into each base
and tighten.
Bases
3
4
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. V3254pr-0920
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO
Handle
4 Screws

5
Musical Fun!
• Push the walker for fun music.
• Press the buttons on the piano and
saxophone, or slide the guitar switch
for tunes and musical scats.
Slide the power/volume
switch to ON with low
volume , ON with high
volume or OFF .
Press
Slide

6
FCC Statement (United States Only)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not expressly
approved by the manufacturer responsible
for compliance could void the user’s authority
to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Consumer Information
Care
• Wipe this toy with a damp cloth.
Do not immerse.
• This product has no consumer
serviceable parts. Do not take this
toy apart.
ICES-003
• This Class B digital apparatus complies
with Canadian ICES-003.
• Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NMB-003
• Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement
du dispositif.