Fisher-Price 73739 User manual

Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool required for assembly and battery installation:
Phillips screwdriver (not included).
Requires three "C" (LR14) alkaline batteries for operation (not included).
Product features and decorations may vary from the pictures above.
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Product Number: 73739
Toddler Driver
Toddler Driver
Toddler Driver
Infant Gym
Infant Gym
Infant Gym

WARNING
To prevent entanglement injury, NEVER place gym in a crib or
playpen. NEVER add strings, ties or other products to this item.
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.
#8 x 19/16" Screw - 8
Parts
2
FASTENERS SHOWN ACTUAL SIZE
Dash BoardBumperWindshield
Kickplate
2 Bases 2 Arms
3 Rings
2 Keys
Mirror
#8 x 13/8" Washer Head Screw - 2

3
Battery Installation
• Locate the battery compartment door on
the back of the dashboard.
• Loosen the screws in the battery compart-
ment door with a Phillips screwdriver.
Remove the battery compartment door.
• Insert three "C" (LR14) alkaline
batteries, as indicated inside the battery
compartment.
• Close the battery compartment door
and tighten the screws with a Phillips
screwdriver. Do not over-tighten.
Hint: When lights or sounds from this toy
become faint or stop, it’s time for an adult
to change the batteries!
Battery Safety Information
• Batteries may leak fluids that can cause
a chemical burn injury or ruin your toy.
To avoid battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the toy. Dispose of
batteries safely. Do not dispose of
batteries in a fire. The batteries may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable
batteries.
• Remove rechargeable batteries from the
toy before charging.
• If removable, rechargeable batteries are
used, they are only to be charged under
adult supervision.
Battery
Compartment
Door
Back View
Dashboard 1.5V x 3
“C” (LR14)
SHOWN ACTUAL SIZE

4
Assembly
• Fit the tabs on the bottom of the
windshield into the slots on the bumper.
• Push down on the windshield to "snap"
it into place.
• Push the tabs on the kickplate into the
slots on the windshield and "snap" the
two together.
• Position the kickplate so that the deco-
rated side faces you.
• Fit one of the pegs on the bottom of the
kickplate into one of the holes near the
base of the bumper.
• Bend the kickplate slightly to fit the
other peg into the corresponding hole
on the other end of the bumper.
Bumper
Kickplate
Windshield
1
1
2
2
3
3
Peg
Hole
Arm
Base
• Fit an arm to the hub on a base
as shown.
• Insert the #8 x 13/8" washer head screw
through the hole in the arm and into the
base. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
• Repeat this procedure to attach the
other arm and base.
4
4
#8 x 13/8"Washer Head Screw
Shown Actual Size
Hub
• Insert the ends of each base into the
square slots in the bumper assembly
as shown.
5
5
Base Ends
Bumper
Assembly

• Fit a ring into the hole in the mirror.
• Clip a ring to each of the hangers.
• Attach a ring or key to the ring or mirror.
Hint: Adjust the height of these toys, as
baby grows.
10
10
Hangers
• Turn the bumper over, so that the bottom
is facing you.
• Be sure the screw holes in the base and
bumper assembly are aligned.
• Insert four #8 x 19/16"screws through the
holes in the bumper assembly and into
the base. Tighten the screws with a
Phillips screwdriver. Do not over-tighten.
6
6
#8 x 19/16" Screw
Shown Actual Size
Bottom View
Bumper
7
7Screws
Visible
• Look into the two holes on each end of
the bumper. If the screws were inserted
properly in this step, they should be
visible in the holes.
• If the screws are not visible, remove the
four screws. Repeat step 6 making sure
the end of the base is fully inserted into
the bumper assembly with no gaps
between the two parts.
Hint: You may feel some resistance.
Press firmly.
• From the back of the dashboard, insert
four #8 x 19/16"screws through the
holes in the dashboard and into the
arms. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
9
9
#8 x 19/16" Screw
Shown Actual Size
Dashboard
5
• Fit the ends of the arms into the holes
in the bottom of the dashboard.
8
8
Support
Arms
Dashboard

6
• To convert to Infant Gym mode, press the button on each support arm and, at the
same time, lift the arch until it "clicks" into position.
• Slide the mode switch to gym mode.
• When your baby kicks the toy, turns the steering wheel or hits the dangling toys,
your child hears a fun song and sees blinking lights and a spinning roller.
• Slide the mode switch to long-play gym mode. Enjoy the same features as
in gym mode but with longer music and lights.
• Slide the mode switch to to turn the power off.
Infant Gym
Hint: If your child is not actively
playing with this toy, it turns off
automatically after a few minutes
(sleep mode).
Buttons
Lift Lift
Press Press
Mode Switch
Wheel
Dangling
To y s

• To convert to Toddler Driver mode, press the button on each support arm and,
at the same time, push the arch down until it "clicks" into position.
• Slide the mode switch to driver mode.
• When your toddler kicks the toy, turns the steering wheel or grabs the dangling
toys, your child hears driving sound effects, a song and sees blinking lights and
a spinning roller.
• Slide the mode switch to to turn power off.
Toddler Driver
Hint: If your child is not actively
playing with this toy, it turns off
automatically after a few minutes
(sleep mode).
7
Mode Switch
Buttons
Push Push
Press Press
Dangling
To y s
Wheel

• Periodically check all screws and tighten as required. Periodically check plastic parts
for cracks and broken pieces.
• Wipe all parts of this toy with a clean cloth dampened with a mild soap and water
solution. Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take this toy apart.
Care
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the equipment.
FCC Note
(United States Only)
Questions? We'd like to hear from you!
Call Fisher-Price®Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST
Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470. Or, write to: Fisher-Price®Consumer Relations,
636 Girard Avenue, East Aurora, New York 14052.
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain:telephone [phone].
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Consumer Information
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.
©2003 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China
73739c-0920