Fisher-Price X7300 User manual

fisher-price.com
X7300
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four “D” (LR20) alkaline batteries (not included) for operation.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).

2
WARNING
Consumer Information
Prevent Entanglement Injury
• Keep out of baby’s reach.
• Remove mobile portion of product from crib or playpen when baby
begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib.
IMPORTANT! Always attach with all provided fasteners tightly to a crib or playpen
according to the instructions. Do not add additional strings or straps to attach to a crib.
Check frequently.
• The mobile portion of this product may be used from birth until 5 months.
• The base portion of this product may be used from birth until 24 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.

3
Parts
Arm
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen
all screws with a Phillips screwdriver. Do not over-tighten the screws.
BaseB
Crib Adaptorib Ada
p
to
r
MobileM
o
bil
e

4
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
Battery Safety Information
1,5V x 4
“D” (LR20)
We recommend using alkaline batteries for longer battery life.
• Loosen the screws in the battery compartment door with a Phillips screwdriver and
remove the door.
• Insert four “D” (LR20) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need to reset the electronics. Slide
the power/volume switch on the mobile base off and then back on.
• When sounds or lights become faint or stop, it’s time for an adult to change the batteries.
Battery Installation

5
Care
ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit
pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities.
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy. The soft toys are surface washable.
• This toy has no consumer serviceable parts. Do not take this toy apart.

6
©2012 Mattel. All Rights Reserved. ® and ™ designate U.S.
trademarks of Mattel, except as noted.
PRINTED IN CHINA X7300b-0920
© Disney
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Consumer Information
CO
N
SU
MER A
SS
I
S
TAN
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.

7
Assembly
• Fit the crib adaptor to the base and tighten the screws.
Crib Adaptor
Base
• Fit the mobile onto the peg on the end of the arm. Push to "snap" in place.
Arm
Mobile
1
2

8
Assembly
• First, press the button on the base, next to the socket Aand then slide the socket door
open B.
• Fit the arm into the socket in the base and tighten the screws.
Socket
B
A
SLIDE
SLIDE PRESS
3

9
Crib Attachment
• Position the toy inside the crib.
• Wrap the toy’s attachment strap around the crib top rail A.
• Slide the end of the attachment strap through the slot on the back of the toy. Pull the end
of the attachment strap up and fasten to the slot on the peg on the back of the toy B.
Note: This toy should be snug against the crib rail and spindles. Use the strap slot that
provides the tightest fit.
• If you have excess strap, slide the free end of the attachment strap under the slot at the
top of the attachment strap C.
Crib Top Rail
Base
Peg
Peg
B
C
A
1

10
Crib Attachment
• Tie the base strings to a crib spindle.
Note: It is better the tie the strings in a knot than a bow, since a bow may be easily untied.
• If the distance between the base and the mattress is less than 7 Inches (18 cm), lower
the crib mattress.
Mattress
Mattress
At Least
At Least
7 Inches (18 cm)
7 Inches (18 cm)
Bottom of Base
Bottom of Base
2
3