Fisher-Price X7751 User manual

X7751
fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four “C” batteries for operation (included).
Batteries included are for demonstration purposes only.
Adult assembly is required for crib attachment and battery replacement.
Tool required: Phillips screwdriver (not included).

2
For best performance, we recom-
mend replacing the batteries that
came with this toy with four, new
“C” (LR14) batteries.
• Locate the battery compartment on
the back of the toy.
• Loosen the screws in the battery
compartment door with a Phillips
screwdriver and remove the door.
Remove the exhausted batteries
and dispose of them properly.
• Insert four, new “C” (LR14)
alkaline batteries.
• Replace the battery compartment
door and tighten the screws. Do not
over-tighten.
• If this toy begins to operate errati-
cally, you may need to reset the
electronics. Slide the power/volume
switch off and back on.
• If sounds, lights or motions become
faint or stop, it's time for an adult to
change the batteries.
In exceptional circumstances,
batteries may leak fluids that can
cause a chemical burn injury or
ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or
batteries of different types: alkaline,
standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Insert batteries as indicated inside
the battery compartment.
• Remove batteries during long
periods of non-use. Always remove
exhausted batteries from the product.
Dispose of batteries safely. Do not
dispose of product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the
battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-recharge-
able batteries.
• Remove rechargeable batteries from
the product before charging.
• If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.
1,5V x 4
“C” (LR14)
Battery
Replacement
Battery Safety
Information

3
Power/Volume Switch
• Slide to ON with low volume , ON
with medium volume , ON with high
volume or OFF .
Sounds Select Switch
• Choose:
Nature Sounds
Classical
Lullabies
Mode Switch
• Choose:
Music Only - plays
approximately 18 minutes of
music/sounds
Music and Lights - plays
approximately 12 minutes of
music/sounds/lights
Music, Lights and Motion -
plays approximately 6 minutes
of music/sounds/lights/motion
Gentle Soothing
Press to start or stop
music/lights/sounds

4
CONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
FCC Statement (United States Only)
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the
receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modications not
expressly approved by the manufacturer
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
ICES-003
• This Class B digital apparatus
complies with Canadian ICES-003.
• Operation is subject to the following
two conditions: (1) this device may
not cause harmful interference and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
NMB-003
• Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada.
• L’utilisation de ce dispositif est
autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du
dispositif doit être prêt à accepter
tout brouillage radioélectrique
reçu, même si ce brouillage est
susceptible de compromettre le
fonctionnement du dispositif.
© Disney
©2012 Mattel. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, except as noted.
PRINTED IN CHINA X7751pr-0920

5
Prevent Entanglement Injury
This product may not attach
to all crib designs. Do not
add additional strings or straps
to attach to a crib or playpen.
Use ONLY attached to a crib
or playpen.
• If the distance between the toy and
the mattress is less than 7 inches,
lower the crib mattress.
WARNING
Mattress
At least
7 inches
Bottom
of Toy
Crib Attachment
Slot
IMPORTANT! Always use the straps
provided to attach this toy to a crib.
Button
• Position the toy inside the crib.
• Wrap one of the toy’s attachment
straps around the crib rail.
Back View
Attachment
Strap
Crib Rail
2
1
• Fasten the attachment strap slot to
the button on the back of the toy.
This toy should be snug against the
crib rail and spindles. Use the strap
slot that provides the tightest fit.
• Repeat this procedure to secure the
other attachment strap.

6
• Wrap the toy’s strings around the
crib spindles and tie in a knot.
Note: It is better to tie the strings in
a knot than a bow, since a bow may
be easily untied.
• To clean, wipe the surface of this toy
with a damp cloth. Do not immerse
this toy.
• Do not drop this toy on a hard surface.
• This toy has no consumer
serviceable parts. Please do not take
this toy apart.
Crib Attachment Care
3
• Protect the environment
by not disposing of this
product with household waste
(2002/96/EC). Check your
local authority for recycling
advice and facilities.