Fisher-Price Barbie Grow-With-Me Trike 72668 User manual

Keep these instructions for future reference, as they contain important information.
Adult assembly is required.
Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood (not included).
If you have any questions about this product, or are missing a part, please call us
toll-free at 1-800-432-KIDS, rather than return this product to the store.
Age: 2 - 6 years.
Weight Limit: 60 lbs.
Grow-With-Me Trike
Instructions
Model Number: 72668

Consumer Information
Consumer Information
2
Thank you for purchasing the BARBIETM Grow-With-Me Trike for your child. The BARBIETM Grow-With-MeTrike starts off as a
regular tricycle for the youngest riders and then converts to a low rider as your child grows.
The BARBIETM Grow-With-Me Trike requires adult assembly. Please set aside at least 30 minutes for assembly. Please read
these instructions carefully and identify all parts before assembly. Refer to the parts illustration for identification.
Questions? We'd like to hear from you!
Call Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers
using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Consumer Relations, 636 Girard Avenue, East Aurora,
New York 14052.
This product contains small parts in its unassembled state.
Adult assembly is required.
Adult supervision is required.
Never use near steps, sloped driveways, hills, ditches, roadways, alleys
swimming pool areas or other bodies of water.
Always wear shoes or sneakers.
Never allow more than one rider.
Fasteners
Fasteners
#8 x 3" Screw – 1 #8 x 3/4" Screw – 4
ALL SHOWN ACTUAL SIZE
Lock Washer – 2 Cap Nut – 2
WARNING
CAUTION

IMPORTANT!
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
• If you are missing a part, please call toll-free 1-800-432-KIDS, rather than return this product to the store.
• Please wipe each part with a clean, dry cloth before assembly.
NOTE: Some parts shown are assembled to both sides of the Trike.
Handlebar
Front Wheel
Pedal Hub - 4
Pedal Axle
Pedal - 2
Fork
Fork Cover - 2
Frame
Seat
Seat Retainer
Rear Wheel
Straight Axle
Hubcap - 2
Gas Cap
Part Not Shown: Label Sheet
Cap Nut - 2
Cap Nut Assembly Tool
Lock Washer - 2
Parts
Parts
3

• Place a scrap block of wood on a flat surface.
• Fit a cap nut into the cap nut assembly tool.
• Place one end of the straight axle into the cap nut.
• Tap the end of the straight axle with a hammer. Make sure
the cap nut is securely attached to the straight axle.
• Remove the cap nut assembly tool from the cap nut.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
Cap Nut
Cap Nut
Assembly Tool
Straight Axle
Rear Wheel
Indented Side Down
4
• Place a scrap block of wood on a flat surface.
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely attached
to the straight axle.
• Dispose of the cap nut assembly tool properly.
• Set the frame assembly aside.
Cap Nut
Rear Wheel
Indented Side Up
Cap Nut
Assembly Tool
Assembled
Rear Wheel
Straight Axle
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Hole Hole
Frame
Straight Axle
Bottom View
Bottom View
Hubcap
Hubcap
Frame
1
2
4
3
Assembly
Assembly
Straight Axle

• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
Pedal Hub
Pedal Hub
Pedal Axle
Tab
Tab
Slot
• While holding the pedal hubs on the pedal axle, insert the
pedal axle through the hole in the center of the front wheel.
Hole
Pedal Axle
Pedal Hubs
Front Wheel
5
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
Pedal Hubs
Pedal Hub
Pedal Hub Pedal Axle
• Turn the front wheel assembly over.
• Insert a pedal hub onto the top of the pedal axle and into
the hole in the center of the front wheel.
• Insert the remaining pedal hub below the pedal axle and
into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
• Insert a lock washer into the slot in the pedal. Make sure
the raised tabs on the lock washer are facing the “closed”
or outside end of the pedal.
• Insert the other lock washer into the other pedal.
Pedal Hubs
Lock Washer
Raised Tabs
Slot
Closed (Outside)
End of Pedal
• Place a scrap block of wood under the front wheel assembly.
• Fit a pedal on the pedal axle.
• With the lock washer centered over the pedal axle end, tap
the pedal with a hammer until it is secure.
• Repeat this procedure to attach the other pedal to the other
end of the pedal axle.
Lock Washer
(Inside)
Pedal Axle
Front Wheel Assembly
Pedal
Assembly
Assembly
5
6
7
8
9
10
11