Flash LED PAR 56 SLIM RGB Aura F7000253a User manual

USER MANUAL
LED PAR 56 Slim
18X3W RGB Aura
F7000253a

LED PAR 56 Slim 18X3W RGB Aura F7000253a
www.flash-butrym.pl
1
1INTRODUCTION
Thank you for purchasing LED PAR 56 Slim 18X3W RGB Aura. For safety reasons and to ensure the
trouble-free operation, carefully read the instructions.
2SAFETY INFORMATION
1. Installation should be done by qualified personnel in order to minimize the risk of accidental
electric shock
2. Disconnect the power supply before installation.
3. Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice
any signs of damage you should contact your dealer immediately. Do not connect the device to
the mains.
4. Do not use the device in high humidity conditions and at temperatures above 40° C
5. The device must be installed on stable structures
3PRODUCT INFORMATION
SLIM LED PAR 56 RGB Aura is a compact unit with bright LEDs (18x3W). Perfect for small stages, clubs or
discos. Applied cap provides a glow effect.
This model has a power output socket, allowing to connect multiple devices in series, using the cables
included.
3.1 Specification
Power consumption: 30W
Power supply voltage: 90 - 240V
Diode type: Standard LED
Number of diodes: 18
Diode power: 3W
Display: LED - 4 characters
Color: RGB
Dimming: Linear: 0 - 100%
Flash frequency (min): 1Hz
Flash frequency (max): 10Hz
Number of DMX channels: 7
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: Automatic, Sound controlled, DMX - Master, DMX - Slave
Features: Error correction, Reset, Automatic DMX 512 signal detection
Additional information: Pass-through sockets, glow effect
AC IN: IEC - C14
AC OUT: IEC - C13
DMX IN: XLR - 3 pin
DMX OUT: XLR - 3 pin
IP Rating: IP20
Housing made: ABS
Cooling: Active
Height [cm]: 23

www.flash-butrym.pl
2
Width [cm]: 19,5
Depth [cm]: 10,5
Weight [kg]: 1,1
Weight with packaging [kg]: 1,3
Set includes: Power cord, Power cord (LINK), Mounting bracket / stand, Mounting screws (for
mounting bracket)
4INSTALLATION
After removing the packaging, check if the device was not damaged during transport. Before connecting to
the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage
caused by unstable mounting.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are
consistent with device requirements. All activities, including connecting the device to the mains must be
performed by qualified personnel.
5CONNECTIONS
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3-pin socket
2. Power (in/out): IEC C13/C14 socket
5.1 Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.
GROUND
DMX +
DMX -
1
2
3
1
2
3
FEMALE
XLR MALE XLR
DMX Controller
DMX 512 DMX 512
5.2 Voltage specification
Input Voltage
Total Power
Frequency
100~245V
150W
50/60Hz

LED PAR 56 Slim 18X3W RGB Aura F7000253a
www.flash-butrym.pl
3
5.3 Connecting power supply
The connection is performed using power cable with PowerCon connector (included).
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are
consistent with device parameters and limitations are not exceeded.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only
on the manufacturer or by a person with appropriate permissions.
6OPERATION MANUAL
6.1 Control panel
1. MENU –go to next parameter, cancel
2. DOWN –change value
3. UP –change value
4. ENTER –save changes
6.2 Menu
Menu diagram:
Red dimmer
r.***
→
0-255
Dark to bright
Green dimmer
r.***
→
0-255
Dark to bright
Blue dimmer
r.***
→
0-255
Dark to bright
Strobe
F.***
→
0-3
No function
4-255
Strobe slow to fast
DMX channel
d.***
→
1-512
Set channel
Color change
P.***
→
0-255
Slow to fast
Smooth color change
L.***
→
0-255
Slow to fast
Color pulse mode
E.***
→
0-255
Slow to fast
Sound mode
SOUD
→
-
ON
6.3 DMX channel list
7CH mode
Channel
Function
Effect
CH 1
Dimmer
0-255: 0-100%
CH 2
Red
0-255: 0-100%
CH 3
Green
0-255: 0-100%
CH 4
Blue
0-255: 0-100%
CH 5
No Function
0-255: No function
CH 6
Program
0-50: No function
51-100: Color change
101-150: Smooth color change
151-200: Pulse mode
201-255: Sound mode
CH 7
Speed for ch 6 (strobe,
color change)
0-255: Slow to fast