Flexispot EG1B-4024-EU User manual

Item No.
EG1B-4024-EU/EG1W-4024-EU/EG1M-4024-EU
Installation Guide

1
2
3
11
6
12
7
4
5
8
9
10 13
14
15
Accessory Package
Specifications Step 1:Install desk feet
01 02
Figures shown are for reference only. Please contact customer service if there are any accessory or
tools missing.
Attach the desk foot (5) to the lifting columns (3 & 4) using 8 M6 bolts (G) and 5x5 hex key (F).
Max. Weight Capacity 60 kg
Max. Speed 25mm/s
Input Voltage 10 0 - 240 V
Min. Height 730 mm
Max. Height 1230 mm
0 - 40 ℃
Duty Cycle 10% (Working 2 minutes then stop 18 minutes)
Working Temperature
Desktop Size 1000 mm in width
600 mm in depth
M6
CX4
BDx2
X2
F
x4 x8
G
M8 2.5x2.5
ST4.2
M6
EX14
ST4.8
Parts Included Diagram of Components
Ax2
M4 Wooden pin
x3
H
5x5
NO. Parts Qty
1
1
1
2
1
1
1
8
5 6
11 12
1 2
7
3 4
910
13 14
15
1
1
1
2
1
1
4
1
NO. Parts Qty
Desktop (small) Desktop (large)
Lifting column Lifting column with motor
Desk foot Support plate
Crossbeam Transmission rod
Baffle Adapter
Adapter holder Power cord
Keypad Cable tie
Patch cord
Gx8
F
5 5x
5
3
4
F
G

03 04
Attach the crossbeam (7) to the lifting columns (3 & 4) with the M8 bolts (C) and tighten them down
with the 5x5 hex key (F).
Step 3:Install crossbeam
Step 2:Install transmission rod
To install the transmission rod, first slot it into lifting column (3) and loosen the hex bolt (Figure. 1).
Extend the transmission rod and slot it into the motor on lifting column (4), then tighten it down with
the included 2.5x2.5 hex key (F) (Figure. 2).
Rotary insert
Note: Please insert the
transmission rod until shaft
stopper touches the column
(Figure.1).
Warning: To ensure both lifting
columns move evenly, do not
rotate the transmission rod more
than 1/3 turn when inserting it into
the motor (Figure. 2).
F
2.5 5x2.
3
4
8
12
CX4
F
5 5x
7
F
C
3
4

Step 4:Install support plates
Attach the support plates (6) to the lifting columns (3 & 4) using M6 bolts (B). Tighten with 5x5
hex key (F).
Step 5: Connect desktops, Install adapter holder, desktop, and keypad
05 06
BX4
F
5 5x
6
F
B
3
4
HX3
1
2H
Connect the small desk top (1) with large desk top (2) using wooden pins (H).
EX12
DX2
D
1
2
11
7
，
E
Put the frame upside down on the underside of the desktop. Attach the adapter holder (11) to
the crossbeam (7). Attach the frame to the desk top using screws (E), Attach the keypad (13)
to the desk top using screws (D).
Note: the holes in the adaptor
holder (11) are not for screws.
The pre-drilled holes in the
desktop are just for your
reference.

Step 6: Install baffles and adapter
Attach the baffle (9) to the crossbeam using M4 bolts(A) and tighten with 2.5x2.5 hex key (F).
Insert the adapter (10) into the holder (11).
07 08
AX2
F
2.5 5x2.
910
F
A
7
Insert
10
11
Step 7: Install and sort out power cord
Connect the power cord (12) to the adapter (10) as shown on the picture.
The cable tie (14) can be used to fasten the cables to the desktop.
Open up Sort out cords Buckle up
14 14
14
21
12
1
10
15
2
Connect the patch cord to DC port
Connect the motor cord to M1 port

09 10
This product cannot be disposed of as household waste. To prevent damage to the
environment, this product should be recycled. Please use the relevant recycling
systems available to you or contract the distributor or manufacturer for recycling
assistance.
Recycling and Disposal
·Power supply: AC100 - 240 V, frequency 50/60HZ;
·Working environment: 0 - 40 ℃;
·Before cleaning, you have to unplug the power supply cable. Clean with a slightly damp cloth to
wipe away the surface dust. Keep all electrical components away from liquids. Do not damage the
connection line and keep the plug in a safe position.
·Inside the control box, there are electronic components, metal parts, plastic parts, wires and so on.
They should be disposed in accordance with the local laws and regulations. They cannot be disposed
as household waste.
·Before using the product, please make sure the product has been installed correctly.
·Before starting use of the product, please read the instructions to fully understand all the product's
functions and settings.
·Keep children away from electric height-adjustable desks, control units and handsets.
Manufacturer is not responsible of any damages that result from children's unpredictable behaviour.
·Slight noise caused by the multi wedge belt or brake system will not impact the use of this product.
·Do not use corrosive or abrasive materials to clean this product and please dispose of cleaning
solutions in an environmentally friendly manner.
·Understand the risks associated with using this product. Children or those with cognitive impairment
should not use this product without supervision.
·If the power supply cord is damaged or broken, it must be replaced by the manufacturer or a relevant
specialist to avoid any injuries.
·Please operate in a clean and safe environment. For example, do not left around your tools. And
always be careful to deal with packaging materials, in order to avoid any kinds of possible danger.
Potential chocking risk exists when children play with plastic bags!
·If necessary, retain the original package for future transportation.
Attention
Keypad Instruction
●
●
▲
▼
UP Button, used to lift the desk surface
DOWN Button, used to lower the desk surface
DOWN Button
UP Button
Height adjusting function
Press the UP button or DOWN button to lift or lower the height of desk surface.
Keypad
●Reset
1. At the lowest position, long press the down button for 5 seconds to enter reset mode. The lifting system
will then bottom out and rebound slightly, indicating that the reset is successful.
2. If the lifting system fails, long press the down button until the lifting system bottoms out and rebounds
slightly to reset the system.
●Troubleshooting
1. If there is no response to pressing the up or down button after a period of continuous work, please let
the desk idle for at least 18 minutes before operating it again.
2. During the lifting process, if the desk reverses its movement unexpectedly, please check whether the
desk load is too heavy or if the desk experiences a lot of shaking while in use.
3. If the lifting columns are uneven and/or not the same height, please refer to the "standing desk leg
problem" video at https://www.flexispot.com/deskresources#3 for troubleshooting.