Fluidwell F030-A User manual

F030-A
BATCH-CONTROLLER
Signal input flowmeter type A: (0)4-20mA.
Control output: one control output for one stage batching.
Options: Intrinsically Safe.
F-Series - Field mounted indicators for safe and hazardous areas. More info: www.fluidwell.com/fseries

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 2
SAFETY INSTRUCTIONS
Any responsibility is lapsed if the instructions and procedures as described in this manual
are not followed.
LIFE SUPPORT APPLICATIONS: The F030-A is not designed for use in life support
appliances, devices, or systems where malfunction of the product can reasonably be
expected to result in a personal injury. Customers using or selling these products for use
in such applications do so at their own risk and agree to fully indemnify the manufacturer
and supplier for any damages resulting from such improper use or sale.
Electro static discharge does inflict irreparable damage to electronics! Before installing or
opening the unit, the installer has to discharge himself by touching a well-grounded object.
This unit must be installed in accordance with the EMC guidelines (Electro Magnetic
Compatibility).
Do connect a proper grounding to the aluminum casing as indicated if the F030-A has been
supplied with the 115-230V AC power-supply type PM. The green / yellow wire between the
back-casing and removable terminal-block may never be removed.
Intrinsically Safe applications: follow the instructions as mentioned in Chapter 5 and
consult “Fluidwell F0..-..-XI - Documentation for Intrinsic Safety”.
DISPOSAL
At the end of its life this product should be disposed of according to local regulations
regarding waste electronic equipment. If a battery is present in this product it should be
disposed of separately. The separate collection and recycling of your waste equipment will
help to conserve natural resources and ensure that it is recycled in a manner that protects
the environment.
SAFETY RULES AND PRECAUTIONARY MEASURES
The manufacturer accepts no responsibility whatsoever if the following safety rules and
precautions instructions and the procedures as described in this manual are not followed.
Modifications of the F030-A implemented without preceding written consent from the
manufacturer, will result in the immediate termination of product liability and warranty period.
Installation, use, maintenance and servicing of this equipment must be carried out by authorized
technicians.
Check the mains voltage and information on the manufacturer's plate before installing the unit.
Check all connections, settings and technical specifications of the various peripheral devices
with the F030-A supplied.
Open the casing only if all leads are free of potential.
Never touch the electronic components (ESD sensitivity).
Never expose the system to heavier conditions than allowed according to the casing
classification (see manufacture's plate and chapter 4.2.).
If the operator detects errors or dangers, or disagrees with the safety precautions taken, then
inform the owner or principal responsible.
The local labor and safety laws and regulations must be adhered to.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 3
ABOUT THE OPERATION MANUAL
This operation manual is divided into two main sections:
The daily use of the unit is described in chapter 2 "Operation". These instructions are meant for
users.
The following chapters and appendices are exclusively meant for electricians/technicians. These
provide a detailed description of all software settings and hardware installation guidance.
This operation manual describes the standard unit as well as most of the options available. For
additional information, please contact your supplier.
A hazardous situation may occur if the F030-A is not used for the purpose it was designed for
or is used incorrectly. Please carefully note the information in this operating manual
indicated by the pictograms:
A "warning" indicates actions or procedures which, if not performed correctly, may lead to
personal injury, a safety hazard or damage of the F030-A or connected instruments.
A "caution" indicates actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the F030-A or connected instruments.
A "note" indicates actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned.
Hardware version : FB03.03.xx
Software version : 03.02.xx
Manual : HF030AEN_v0403_03 Atex_IECEx_CSA_FM
© Copyright 2012 : Fluidwell bv - The Netherlands.
Information in this manual is subject to change without prior notice. The
manufacturer is not responsible for mistakes in this material or for incidental
damage caused as a direct or indirect result of the delivery, performance or
use of this material.
© All rights reserved. No parts of this publication may be reproduced or used
in any form or by any means without written permission of your supplier.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 4
CONTENTS MANUAL
Safety instructions ........................................................................................................................................... 2
Disposal .................................................................................................................................................... 2
Safety rules and precautionary measures ....................................................................................................... 2
About the operation manual ............................................................................................................................ 3
Contents manual.............................................................................................................................................. 4
1. Introduction ................................................................................................................................. 5
1.1. System description of the F030-A.......................................................................................... 5
2. Operational.................................................................................................................................. 6
2.1. General .................................................................................................................................. 6
2.2. Control panel.......................................................................................................................... 6
2.3. Operator information and functions ....................................................................................... 7
3. Configuration............................................................................................................................... 9
3.1. Introduction ............................................................................................................................ 9
3.2. Programming SETUP-level.................................................................................................... 9
3.2.1. General .................................................................................................................................. 9
3.2.2. Overview functions SETUP level ......................................................................................... 12
3.2.3. Explanation OF SETUP-functions........................................................................................ 13
1 - Preset ........................................................................................................................ 13
2 - Overrun...................................................................................................................... 14
3 - Display ....................................................................................................................... 14
4 - Power management .................................................................................................. 14
5 - Flowmeter .................................................................................................................. 15
5 - Flowmeter (continued)............................................................................................... 16
6 - Others ........................................................................................................................ 17
4. Installation ................................................................................................................................. 18
4.1. General directions................................................................................................................ 18
4.2. Installation / surrounding conditions .................................................................................... 18
4.3. Dimensions- Enclosure ........................................................................................................ 19
4.4. Installing the hardware......................................................................................................... 21
4.4.1. Introduction .......................................................................................................................... 21
4.4.2. Terminal connectors with power supply - type : PB / PD / PL / PX ..................................... 22
4.4.3. Terminal connectors with power supply - type : PF / PM .................................................... 23
5. Intrinsically safe applications..................................................................................................... 26
5.1. General information and instructions: .................................................................................. 26
5.2. Terminal connectors Intrinsically Safe applications: ............................................................ 28
5.3. Configuration examples Intrinsically Safe applications:....................................................... 28
5.4. Battery replacement instructions.......................................................................................... 30
6. Maintenance.............................................................................................................................. 31
6.1. General directions................................................................................................................ 31
6.2. Repair................................................................................................................................... 31
Appendix A: Technical specification .............................................................................................................. 32
Appendix B: Problem solving......................................................................................................................... 35
Index of this manual....................................................................................................................................... 36
List of figures in this manual .......................................................................................................................... 37
Notes .................................................................................................................................................. 38

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 5
1. INTRODUCTION
1.1. SYSTEM DESCRIPTION OF THE F030-A
Functions and features
The batch controller model F030-A is a microprocessor driven instrument designed for batching and
filling of small batch sizes up to medium large quantities as well as displaying total and accumulated
total.
This product has been designed with a focus on:
ultra-low power consumption to allow long-life battery powered applications (type PB / PC),
intrinsic safety for use in hazardous applications (type XI),
several mounting possibilities with GRP or aluminum enclosures for industrial surroundings,
ability to process all types of flowmeter signals,
one control output for controlling a pump or valve.
Flowmeter input
This manual describes the unit with an (0)4-20mA type input from the flowmeter "-A version". Other
versions are available to process pulse or 0-10V flowmeter signals.
One flowmeter with a (0)4-20mA output can be connected to the F030-A. To power the sensor,
several options are available.
Fig. 1: Typical application for the F030-A.
Configuration of the unit
The F030-A has been designed to be implemented in many types of applications. For that reason, a
SETUP-level is available to configure your F030-A according to your specific requirements.
It includes several important features, such as Span, measurement units, signal selection etc. All
setting are stored in EEPROM memory and will not be lost in the event of power failure. To extend
the battery-life time, please use of the power-management functions as described in chapter 3.2.3.
Display information
The unit has a large transflective LCD with all kinds of symbols and digits to display measuring units,
status information, count up or count down and key-word messages.
A backup of the total and accumulated total in EEPROM memory is made every minute.
Options
The following options are available: intrinsic safety, mechanical relay or active outputs, power- and
sensor-supply options, panel-mount, wall-mount and weather-proof enclosures, flame proof
enclosure and LED backlight.
Overview typical application F030

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 6
2. OPERATIONAL
2.1. GENERAL
The F030-A may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
Take careful notice of the " Safety rules, instructions and precautionary measures " in the
front of this manual.
This chapter describes the daily use of the F030-A. This instruction is meant for users / operators.
2.2. CONTROL PANEL
The following keys are available:
Fig. 2: Control Panel.
Functions of the keys
This key is used to program and save new values or settings.
It is also used to gain access to SETUP-level; please read chapter 3.
This key is used to START the batch process.
The arrow-key is used to increase a value after PROG has been pressed
or to configure the unit; please read chapter 3.
Press STOP to "PAUSE" the batch process. When this key is pressed twice,
the process is completely finished and can't be continued.
STOP is also used to select Total and accumulated total.
After PROG has been pressed, the arrow-key is used to select a value
STOP

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 7
2.3. OPERATOR INFORMATION AND FUNCTIONS
In general, the F030-A will always act at Operator level. The information displayed is dependant
upon the SETUP-settings. All pulses generated by the connected flowmeter are measured by the
F030-A in the background, whichever screen refresh rate setting is chosen. After pressing a key, the
display will be updated very quickly during a 30 second period, after which it will slow-down again.
To enter a batch quantity
To change the PRESET-value, following procedure must be followed:
1) press PROG: the word "PROGRAM" will be flashing,
2) use to select the digits and to increase that value,
3) set the new PRESET-value by pressing ENTER.
Fig. 3: Example display information during programming preset value.
When data is altered but ENTER has not been pressed yet, then the alteration can still be
cancelled by waiting for 20 seconds or by pressing ENTER during three seconds: the former
value will be reinstated. The PRESET-value can be used time after time till a new value is
programmed.
Please note that alterations will only be set after ENTER has been pressed!
Batch maximum
When you program a new value which is not valid - the batch size is too large - the decrease-
signwill be displayed while you are programming; the new value will not be accepted!
Starting up the batch process
The batch process can only be started up when "READY" is displayed. The batch process is
started-up by pressing the START-key.
The arrows at the display indicate if the ACTUAL-value is / was counting up or down.
Fig. 4: Example display information during the process.
RUN PAUSESET-UP
A
LARMPROGRAMREADY
RUN PAUSE
LOW BATTERY
SET-UP
A
LARMPROGRAMREADY

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 8
Interrupting and ending the batch process
When STOP is pressed once, the batch process will be temporarily interrupted; the actual
values are not lost. At the display, the word "PAUSE" will be flashing. From this stage, the
batch process can be resumed with the START-key.
The process can be ended entirely at all times by pressing STOP twice in which case the
actual values are "lost" and the system returns to steady state: the batch can not be resumed.
Fig. 5: Example display information when interrupted.
After batching, following functions are available:
Display total and accumulated total
When the STOP-key is pressed, total and accumulated total are displayed. The accumulated
total cannot be re-initialized. The value will count up to 99,999,999,999. The unit and number
of decimals are displayed according to the configuration settings for preset.
Clear total
The value for total can be re-initialized. To do so, select the Total display and press PROG
followed by STOP. After pressing PROG, the flashing text "PUSH STOP" is displayed.
To avoid re-initialization at this stage, press another PROG again or wait for 20 seconds.
Re-initialization of total DOES NOT influence the accumulated total.
Low-battery alarm
When the battery voltage drops, it must be replaced. At first "low-battery" will flash, but as
soon as it is displayed continuously, the battery MUST be replaced shortly after!
Only original batteries supplied by the manufacturer may be used, else the guarantee and
liability will be terminated. The remaining lifetime after the first moment of indication is
generally several days up to some weeks.
Fig. 6: Example of low-battery alarm.
Range error
As soon as the input value is 5% outside the calibrated measuring range, “ALARM”
will be displayed. Meanwhile, the calibrated value will be displayed.
After pressing the SELECT key, the reason of the alarm will be displayed: “LO RANGE” or
“HI RANGE”.
Alarm 01-03
When "ALARM" is displayed, press the SELECT key to display the reason of the alarm: 1-3.
Please consult Appendix B: problem solving.
RUN PAUSE
LOW BATTERY
SET-UP
A
LARMPROGRAMREADY
RUN PAUSE
LOW BATTERY
SET-UP
A
LARMPROGRAMREADY

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 9
3. CONFIGURATION
3.1. INTRODUCTION
This and the following chapters are exclusively meant for electricians and non-operators. In these,
an extensive description of all software settings and hardware connections are provided.
Mounting, electrical installation, start-up and maintenance of the instrument may only be
carried out by trained personnel authorized by the operator of the facility. Personnel must
read and understand this Operating Manual before carrying out its instructions.
The F030-A may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
Ensure that the measuring system is correctly wired up according to the wiring diagrams. The
housing may only be opened by trained personnel.
Take careful notice of the " Safety rules, instructions and precautionary measures " in the
front of this manual.
3.2. PROGRAMMING SETUP-LEVEL
3.2.1. GENERAL
Configuration of the F030-A is done at SETUP-level. SETUP-level is reached by pressing the
PROG/ENTER key for 7 seconds; at which time, both arrows will be displayed. In order to return
to the operator level, PROG will have to be pressed for three seconds. Alternatively, if no keys are
pressed for 2 minutes, the unit will exit SETUP automatically.
SETUP can be reached at all times while the F030-A remains fully operational.
Note: A pass code may be required to enter SETUP. Without this pass code access to SETUP is
denied.
To enter SETUP-level:

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 10
Matrix structure SETUP-level:
SCROLLING THROUGH SETUP-LEVEL
Selection of function-group and function:
SETUP is divided into several function groups and functions.
Each function has a unique number, which is displayed below the word "SETUP" at the bottom of
the display. The number is a combination of two figures. The first figure indicates the function-group
and the second figure the sub-function. Additionally, each function is expressed with a keyword.
After selecting a sub-function, the next main function is selected by scrolling through all "active" sub-
functions (e.g. 1, 11, 12, 13, 14, 1, 2, 3, 31 etc.).

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 11
To change or select a value:
To change a value, use to select the digits and to increase that value.
To select a setting, both and can be used.
If the new value is invalid, the increase signor decrease-signwill be displayed while you are
programming.
When data is altered but ENTER is not pressed, then the alteration can still be cancelled by waiting
for 20 seconds or by pressing ENTER for three seconds: the PROG-procedure will be left
automatically and the former value reinstated.
Note: alterations will only be set after ENTER has been pressed!
To return to OPERATOR-level:
In order to return to the operator level, PROG will have to be pressed for three seconds. Also, when
no keys are pressed for 2 minutes, SETUP will be left automatically.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 12
3.2.2. OVERVIEW FUNCTIONS SETUP LEVEL
SETUP FUNCTIONS AND VARIABLES
1 PRESET
11 UNIT L - m3 - kg - lb - GAL - USGAL - bbl - no unit
12 DECIMALS 0 - 1 - 2 - 3 (Ref: displayed value)
13 SPAN 0.000001 - 999,999 unit / second
14 DECIMALS SPAN 0 – 6
15 BATCH MAXIMUM X,XXX,XXX quantity
2 OVERRUN
21 OVERRUN disable - enable
22 TIME 0.1 - 999.9 seconds
3 DISPLAY
31 DISPLAY increase - decrease
32 BACKLIGHT (optional) off - green - amber
33 BL. BRIGHTNESS 1 - 5
4 POWER MANAGEMENT
41 LCD UPDATE fast - 1 sec - 3 sec - 15 sec - 30 sec - off
42 BATTERY MODE operational - shelf
5 FLOWMETER
51 FORMULA interpolation, square root
52 FILTER 00 - 99
53 CUT-OFF 0.0 - 99.9%
54 CALIBRATE LOW default - calibrate - calibrate set
55 CALIBRATE HIGH default - calibrate - calibrate set
6 OTHERS
61 TYPE / MODEL F030-A
62 SOFTWARE VERSION v03._ _._ _
63 SERIAL NO. _ _ _ _ _ _ _
64 PASSWORD 0000 - 9999
65 TAGNUMBER 0000000 - 9999999

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 13
3.2.3. EXPLANATION OF SETUP-FUNCTIONS
1 - PRESET
MEASUREMENT UNIT
11
SETUP - 11 determines the measurement unit for preset, total,
accumulated total and pulse output. The following units can be selected:
L - m3 - kg - lb. - GAL - USGAL - bbl - _ (no unit).
Alteration of the measurement unit will have consequences for operator
and SETUP-level values.
Please note that the K-factor has to be adapted as well; the calculation is
not done automatically.
DECIMALS
12
The decimal point determines for preset, total and accumulated total the
number of digits following the decimal point.
The following can be selected:
0000000 - 111111.1 - 22222.22 - 3333.333
SPAN
13
With the span, the flowmeter signal is converted to a quantity.
The span for Preset is determined on the basis of the measurement unit
(setting 11) and the flowrate per second at 20mA.
Enter the span in whole numbers (decimals are set with SETUP 14).
The more accurate the span, the more accurate the functioning of the
system will be:
Example 1 Calculating the Span.
Let us assume that the flowmeter generates 20mA at a rate of
652.31 USGAL per hour, the selected unit is barrels.
There are 42 gallons in one barrel; so the rate is 652.31/42 is
15.53119 barrels/hour.
This is 0.0043142 barrels/second, which is the span.
Enter for SETUP - 13: "004314" and for SETUP - 14 "6".
Example 2 Calculating the Span.
Let us assume that the flowmeter generates 20mA at a
flowrate of 2,481.3 Liters/minute and the selected unit is "cubic
meters / m3".
The rate per second is 2,481.3÷60 is 41.355 L/sec.
This is 0.041355 m3/sec., which is the span.
Enter for SETUP - 13: "041355" and for SETUP - 14 - decimals
span "6".
DECIMALS SPAN
14
This setting determines the number of decimals for the Span
(SETUP 13). The following can be selected:
0 - 1 - 2 - 3 - 4 - 5 - 6
Please note that this function influences the accuracy of the Span
indirectly.
This setting has NO influence on the displayed number of digits for total
(SETUP 12)!
BATCH MAXIMUM
15
This function limits the operator to enter a new preset-value which is more
as the entered batch maximum.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 14
2 - OVERRUN
Overrun can occur at the end of the batch process, as a result of slowness of a valve / pump.
Consequently, the accuracy is less. With this function, the F030-A analyses the actual overrun
characteristic after every batch. This information is used to correct the overrun automatically.
OVERRUN
21
For an accurate overrun correction, it is necessary that the flow meter
meets certain technical demands, such as "an accurate output" and a fast
response. Do not enable this function if the flow meter does not meet
these technical demands.
OVERRUN TIME
22
The overrun characteristic of the system will be analyzed during a certain
time after the batch. In this way, false signal generated through leakage
are eliminated.
Enter here the expected time needed by the system to stop a batch. It is
advisable to provide extra time in order to avoid an incorrect overrun
correction or false leakage alarms.
Note that the next batch can only be started after elapsing of this overrun
time!
The minimum overrun time is 0.1 second, maximum 999.9 seconds.
3 - DISPLAY
DISPLAY
31
The large 17mm digits can be set to display the actual batched quantity
(increase) OR to display the remaining quantity to be batched (decrease).
The functions below will only effect the optional LED-backlight.
BACKLIGHT
(OPTION)
32
If a LED backlight has been supplied, the color can be selected.
Following selections are available:
OFF - GREEN - AMBER
BRIGHTNESS
(OPTION)
33
The density of the backlight can be set in the range: 1 - 5
One is minimum and five is maximum brightness.
4 - POWER MANAGEMENT
When used with the internal battery option, the user can expect reliable measurement over a long
period of time. The F030-A has several smart power management functions to extend the battery life
time significantly. Two of these functions can be set:
LCD NEW
41
The calculation of the display-information influences the power
consumption significantly. When the application does not require a fast
display update, it is strongly advised to select a slow refresh rate.
Please understand that NO information will be lost; the input signal will be
processed and the output signal will be generated in the normal way.
The following can be selected:
Fast - 1 sec - 3 sec - 15 sec - 30 sec - off.
Example battery life-time:
battery life-time with a FAST update: about 3 years.
battery life-time with a 1 sec update: about 5 years.
Note: after a button has been pressed by the operator - the display
refresh rate will always switch to FAST for 30 seconds. When "OFF" is
selected, the display will be switched off after 30 seconds and will be
switched on as soon as a button has been pressed.
BATTERY-MODE
42
The unit has two modes: operational or shelf.
After "shelf" has been selected, the unit can be stored for several years; it
will not process the sensor signal; the display is switched off but all
settings and totals are stored. In this mode, power consumption is
extremely low.
To wake up the unit again, press the SELECT-key twice.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 15
5 - FLOWMETER
SIGNAL
51
The F030-A can process the (0)4-20mA signal in two ways:
Interpolation: the signal is processed linear
R = S x I
Square root: for differential pressure
R = S √I
where:
R = Rate: the calculated flowrate
S = Span: the maximum flowrate at 20mA. The span is programmed
with setting 24 for flowrate and with setting 13 for total.
I = Input: the scaled analog value; in these formulas value 0 (zero)
for (0)4mA and value 1 (one) for 20mA.
FILTER
52
The analog output signal of a flowmeter does mirror the actual flow. This
signal is measured several times a second by the F030-A. The value
measured is a "snap-shot" of the real flow as it will be fluctuating. With the
help of this digital filter a stable and accurate reading can be obtained
while the filter level can be set to a desired value.
The filter principal is based on three input values: the filter level (01-99),
the last measured analog value and the last average value. The higher
the filter level, the longer the response time on a value change will be.
Below, several filter levels with there response times are indicated:
FILTER VALUE RESPONSE TIME ON STEP CHANGE OF ANALOG VALUE.
TIME IN SECONDS
50%INFLUENCE 75%INFLUENCE 90% INFLUENCE 99% INFLUENCE
01 filter disabled filter disabled filter disabled filter disabled
02 0.3 seconds 0.5 seconds 1.0 seconds 1.8 seconds
03 0.5 seconds 1.0 seconds 1.5 seconds 3 seconds
05 1.0 seconds 1.8 seconds 2.8 seconds 5.3 seconds
10 1.8 seconds 3.5 seconds 5.6 seconds 11 seconds
20 3.5 seconds 7.0 seconds 11 seconds 23 seconds
30 5.3 seconds 10 seconds 17 seconds 34 seconds
50 8.8 seconds 17 seconds 29 seconds 57 seconds
75 13 seconds 26 seconds 43 seconds 86 seconds
99 17 seconds 34 seconds 57 seconds 114 seconds
Continued next page >>>

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 16
5 - FLOWMETER (CONTINUED)
CUT-OFF
53
To ignore e.g. leakage of the flow or vibration, a low-flow cut-off can be
set as percentage over the full range of 16mA (or 20mA). When the
analog value is less then required with this setting, the signal will be
ignored.
The cut-off value can be programmed is the range 0.0 - 99.9%.
Examples:
FUNCTION
(setup 51) SPAN (setup
13/24)
REQUIRED
CUT-OFF CUT-OFF (setup 53) REQUIRED OUTPUT
interpolation 450 L/min 25 L/min 25/450 x 100%=5.5% 16mA x 5.5% + 4mA = 4.88mA
square root 450 L/min 25 L/min (25/450)2 x 100%=0.3% 16mA x 0.3% + 4mA = 4.05mA
TUNE MIN / 4MA
54
With this setting it is possible to calibrate the input value for (0)4mA as the
signal from the flowmeter might not be exact 4.0 mA (or 0.0 mA) at
flowrate zero.
This function will measure the real output value at flow zero.
Please note: the input loop powered version - type A-PL - requires a
signal from 4mA and not lower!
Warning: be very sure that the offered signal is correct
before the calibration is executed as this function has major
influences on the accuracy of the system!
After pressing PROG, three settings can be selected:
CALIBRATE: with this setting, the input will be calibrated with the
actual "(0)4mA" value. After pressing enter, CAL SET will be
displayed as soon as the calibration is completed. From that moment,
the analog value must be more than the calibrated value before the
signal will be processed.
DEFAULT: with this setting, the manufactures value is re-installed.
CAL SET: to select the last calibrated value.
TUNE MAX / 20MA
55
With this setting it is possible to calibrate the input value for 20mA as the
signal from the flowmeter might not be exact 20.0 mA at maximum
flowrate.
This function will measure the real output value at maximum flowrate.
Warning: be very sure that the offered signal is correct
before the calibration is executed as this function has major
influences on the accuracy of the system!
After pressing PROG, three settings can be selected:
CALIBRATE: with this setting, the input will be calibrated with the
actual "20mA" value. After pressing enter, CAL SET will be displayed
as soon as the calibration is completed. From that moment, the
analog value must be less than the calibrated value for a reliable
measurement.
DEFAULT: with this setting, the manufactures value is re-installed.
CAL SET: to select the last calibrated value.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 17
6 - OTHERS
TYPE OF MODEL
61
For support and maintenance it is important to have information about the
characteristics of the F030-A.
Your supplier will ask for this information in the case of a serious
breakdown or to assess the suitability of your model for upgrade
considerations.
VERSION SOFTWARE
62
For support and maintenance it is important to have information about the
characteristics of the F030-A.
Your supplier will ask for this information in the case of a serious
breakdown or to assess the suitability of your model for upgrade
considerations.
SERIAL NUMBER
63
For support and maintenance it is important to have information about the
characteristics of the F030-A.
Your supplier will ask for this information in the case of a serious
breakdown or to assess the suitability of your model for upgrade
considerations.
PASS CODE
64
All SETUP-values can be pass code protected.
This protection is disabled with value 0000 (zero).
Up to and including 4 digits can be programmed, for example 1234.
TAGNUMBER
65
For identification of the unit and communication purposes, a unique tag
number of maximum 7 digits can be entered.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 18
4. INSTALLATION
4.1. GENERAL DIRECTIONS
Mounting, electrical installation, start-up and maintenance of this instrument may only be
carried out by trained personnel authorized by the operator of the facility. Personnel must
read and understand this Operating Manual before carrying out its instructions.
The F030-A may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
Ensure that the measuring system is correctly wired up according to the wiring diagrams.
Protection against accidental contact is no longer assured when the housing cover is
removed or the panel cabinet has been opened (danger from electrical shock). The housing
may only be opened by trained personnel.
Take careful notice of the " Safety rules, instructions and precautionary measures " at the
front of this manual.
4.2. INSTALLATION / SURROUNDING CONDITIONS
Take the relevant IP classification of the casing into account (see manufactures plate). Even an IP67
(NEMA 4X) casing should NEVER be exposed to strongly varying (weather) conditions.
When panel-mounted, the unit is IP65 (NEMA 4)!
When used in very cold surroundings or varying climatic conditions, take the necessary precautions
against moisture by placing a dry sachet of silica gel, for example, inside the instrument case.
Mount the F030-A on a solid structure to avoid vibrations.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 19
4.3. DIMENSIONS- ENCLOSURE
Aluminum enclosures:
75 mm (2.95")
130 mm (5.12") 112 mm (4.40")
60 mm (2.36")
120 mm (4.72")
M20 x 1,5
PG9 PG9
30mm 30mm
22,5mm
M20 x 1,5
M16 x 1,5 M16 x 1,5
30mm 30mm
22,50mm
M20 x 1,5
22,5mm
M20 x 1,5 M20 x 1,5
25mm 25mm
22,5mm
1/2"NPT
0.9"
3x 1/2"NPT
0.12" 0.12"
0.9"
HA
HM
HN
HO
HP
HT
HU
6 x M12
12mm 12mm
24mm24mm 36mm
36mm
14mm 17mm
115 mm (4.53”)
98 mm (3.86”)
HB
29.1 mm (1.15”)
31 mm
(1.22”)
HZ
4x M20 x 1,5
15 15
15
HV
2323
16
mm
Fig. 7: Dimensions Aluminum enclosures.

HF030AEN_v0403_03 Atex_IECEx_CSA_FM
Page 20
GRP enclosures:
75 mm (2.95")
130 mm (5.12") 112 mm (4.40")
60 mm (2.36")
120 mm (4.72")
HD
HK
HK back box:
(flat bottom)
HE
HF
HG
HH
D=12mm
12mm12mm
24mm24mm 36mm
36mm
14mm 17mm
22,5mm
30mm 30mm
D=16mm
D=20mm
0.9"
D=22mm (0.866")
22,5mm
25mm 25mm
D=20mm D=20mm
D=16mm
HC
75 mm (2.95") 118 mm (4.65”)
104 mm (4.09”)
HJ
0.9”
0.12” 0.12”
3x D=22mm (0.866”)
115 mm (4.53”)
98 mm (3.86”)
29.1 mm (1.15”)
31 mm
(1.22”)
Fig. 8: Dimensions GRP enclosures.