Fluidwell F131-P User manual

F131-P
BATCH-CONTROLLER
Signal input flowmeter: pulse, Namur and coil
Status inputs: start and stop
Signal outputs: two control outputs for two stage control, or
one control output and pulse output ref. total
Signal outputs: 4-20mA ref. flowrate and pulse ref. total
Options: Intrinsically Safe, Modbus communication
F-Series - Field mounted indicators for safe and hazardous areas. More info: www.fluidwell.com/fseries

HF131PEN_v0501_05
Page 2
SAFETY INSTRUCTIONS
Any responsibility is lapsed if the instructions and procedures as described in this
manual are not followed.
LIFE SUPPORT APPLICATIONS: The F131-P is not designed for use in life support
appliances, devices, or systems where malfunction of the product can reasonably be
expected to result in a personal injury. Customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify the
manufacturer and supplier for any damages resulting from such improper use or sale.
Electro static discharge does inflict irreparable damage to electronics! Before installing
or opening the unit, the installer has to discharge himself by touching a well-grounded
object.
This unit must be installed in accordance with the EMC guidelines (Electro Magnetic
Compatibility).
Do connect a proper grounding to the aluminum casing (option HA/HU) as indicated if
the F131-P has been supplied with the 115-230V AC power-supply option PM.
The green/yellow wire between the back-casing and removable terminal-block may
never be removed.
Intrinsically Safe applications: follow the instructions as mentioned in Chapter 5 and
consult “Fluidwell F1..-..-XI - Documentation for Intrinsic Safety”.
DISPOSAL
At the end of its life this product should be disposed of according to local regulations regarding
waste electronic equipment. If a battery is present in this product it should be disposed of
separately. The separate collection and recycling of your waste equipment will help to conserve
natural resources and ensure that it is recycled in a manner that protects the environment.
SAFETY RULES AND PRECAUTIONARY MEASURES
The manufacturer accepts no responsibility whatsoever if the following safety rules and
precautions instructions and the procedures as described in this manual are not followed.
Modifications of the F131-P implemented without preceding written consent from the
manufacturer, will result in the immediate termination of product liability and warranty period.
Installation, use, maintenance and servicing of this equipment must be carried out by authorized
technicians.
Check the mains voltage and information on the manufacturer's plate before installing the unit.
Check all connections, settings and technical specifications of the various peripheral devices
with the F131-P supplied.
Open the casing only if all leads are free of potential.
Never touch the electronic components (ESD sensitivity).
Never expose the system to heavier conditions than allowed according to the casing
classification (see manufacture's plate and chapter 4.2.).
If the operator detects errors or dangers, or disagrees with the safety precautions taken, then
inform the owner or principal responsible.
The local labor and safety laws and regulations must be adhered to.

HF131PEN_v0501_05
Page 3
ABOUT THE OPERATION MANUAL
This operation manual is divided into two main sections:
The daily use of the unit is described in chapter 2 "Operation". These instructions are meant for
users.
The following chapters and appendices are exclusively meant for electricians/technicians. These
provide a detailed description of all software settings and hardware installation guidance.
This operation manual describes the standard unit as well as most of the options available. For
additional information, please contact your supplier.
A hazardous situation may occur if the F131-P is not used for the purpose it was designed for
or is used incorrectly. Please carefully note the information in this operating manual
indicated by the pictograms:
A "warning" indicates actions or procedures which, if not performed correctly, may lead to
personal injury, a safety hazard or damage of the F131-P or connected instruments.
A "caution" indicates actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the F131-P or connected instruments.
A "note" indicates actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned.
Hardware version : 02.01.xx
Software version : 02.05.xx
Manual : HF131PEN_v0501_05
© Copyright 2011 : Fluidwell bv - The Netherlands.
Information in this manual is subject to change without prior notice. The
manufacturer is not responsible for mistakes in this material or for incidental
damage caused as a direct or indirect result of the delivery, performance or
use of this material.
© All rights reserved. No parts of this publication may be reproduced or used
in any form or by any means without written permission of your supplier.

HF131PEN_v0501_05
Page 4
CONTENTS MANUAL
Safety instructions ........................................................................................................................................... 2
Disposal .................................................................................................................................................... 2
Safety rules and precautionary measures ....................................................................................................... 2
About the operation manual ............................................................................................................................ 3
Contents manual.............................................................................................................................................. 4
1. Introduction ................................................................................................................................. 5
1.1. System description of the F131-P.......................................................................................... 5
2. Operational.................................................................................................................................. 7
2.1. General .................................................................................................................................. 7
2.2. Control panel.......................................................................................................................... 7
2.3. Operator information and functions ....................................................................................... 8
3. Configuration............................................................................................................................. 10
3.1. Introduction .......................................................................................................................... 10
3.2. Programming SETUP-level.................................................................................................. 10
3.2.1. General ................................................................................................................................ 10
3.2.2. Overview functions SETUP level ......................................................................................... 13
3.2.3. Explanation OF SETUP-functions........................................................................................ 14
1 - Preset ........................................................................................................................ 14
2 - Flowrate ..................................................................................................................... 15
3 - Overrun...................................................................................................................... 16
4 - Display ....................................................................................................................... 16
5 - Power management .................................................................................................. 16
6 - Flowmeter .................................................................................................................. 17
7 - Analog output............................................................................................................. 18
8 - Relay output............................................................................................................... 20
9 - Communication (optional).......................................................................................... 21
A - Others........................................................................................................................ 21
4. Installation ................................................................................................................................. 22
4.1. General directions................................................................................................................ 22
4.2. Installation / surrounding conditions .................................................................................... 22
4.3. Dimensions- Enclosure ........................................................................................................ 23
4.4. Installing the hardware......................................................................................................... 25
4.4.1. Introduction .......................................................................................................................... 25
4.4.2. Voltage selection sensor supply .......................................................................................... 26
4.4.3. Terminal connectors ............................................................................................................ 27
5. Intrinsically safe applications..................................................................................................... 35
5.1. General information and instructions ................................................................................... 35
5.2. Terminal connectors Intrinsically Safe applications ............................................................. 36
5.3 Configuration Examples....................................................................................................... 38
5.4 Battery replacement instructions.......................................................................................... 41
6. Maintenance.............................................................................................................................. 42
6.1. General directions................................................................................................................ 42
Appendix A: Technical specification .............................................................................................................. 43
Appendix B: Problem solving......................................................................................................................... 46
Appendix C: Communication variables.......................................................................................................... 47
Index of this manual....................................................................................................................................... 51

HF131PEN_v0501_05
Page 5
1. INTRODUCTION
1.1. SYSTEM DESCRIPTION OF THE F131-P
Functions and features
The batch controller model F131-P is a microprocessor driven instrument designed for batching and
filling of small batch sizes up to large quantities as well as displaying the flowrate, total and
accumulated total.
This product has been designed with a focus on:
ultra-low power consumption to allow long-life battery powered applications (option PB),
intrinsic safety for use in hazardous applications (option XI),
several mounting possibilities with ABS or aluminum enclosures for harsh industrial
surroundings,
ability to process all types of flowmeter signals,
transmitting possibilities with analog / pulse and communication (option) outputs.
Flowmeter input
This manual describes the unit with a pulse type input from the flowmeter "-P version". Other
versions are available to process (0)4-20mA or 0-10V flowmeter signals.
One flowmeter with a passive or active pulse, Namur or coil signal output can be connected to the
F131-P. To power the sensor, several options are available.
Standard outputs
Two transistor or relay (option) outputs: for two-stage control or one stage control with pulse
output. The configurable pulse output offers a scaled pulse mirroring a certain totalised quantity.
Maximum frequency 60Hz.; the pulse length can be set from 7,8msec up to 2 seconds.
Configurable passive linear 4-20mA analog output with 10-bits resolution mirroring the actual
flowrate. Flowrate levels as well as the minimum and maximum signal output can be tuned.
Fig. 1: Typical application for the F131-P.

HF131PEN_v0501_05
Page 6
Configuration of the unit
The F131-P was designed to be implemented in many types of applications. For that reason, a
SETUP-level is available to configure your F131-P according to your specific requirements.
SETUP includes several important features, such as K-factors, measurement units, signal selection
etc. All setting are stored in EEPROM memory and will not be lost in the event of power failure or a
drained battery.
To extend the battery-life time (option), please make use of the power-management functions as
described in chapter 3.2.3.
Display information
The unit has a large transflective LCD with all kinds of symbols and digits to display measuring units,
status information, trend-indication and key-word messages.
A backup of the total and accumulated total in EEPROM memory is made every minute.
Options
The following options are available: isolated or active 4-20mA / 0-10V / 0-20mA analog output, full
Modbus communication RS232/485 (also battery powered), intrinsic safety, mechanical relay or
active outputs, power- and sensor-supply options, panel-mount, wall-mount and weather-proof
enclosures, flame proof enclosure.

HF131PEN_v0501_05
Page 7
2. OPERATIONAL
2.1. GENERAL
The F131-P may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
Take careful notice of the " Safety rules, instructions and precautionary measures " in
the front of this manual.
This chapter describes the daily use of the F131-P. This instruction is meant for users / operators.
2.2. CONTROL PANEL
The following keys are available:
Fig. 2: Control Panel.
Functions of the keys
This key is used to program and save new values or settings.
It is also used to gain access to SETUP-level; please read chapter 3.
This key is used to START the batch process.
The arrow-key is used to increase a value after PROG has been pressed
or to configure the unit; please read chapter 3.
Press STOP to "PAUSE" the batch process. When this key is pressed twice,
the process is completely finished and can't be continued.
STOP is also used to select Total and accumulated total.
After PROG has been pressed, the arrow-key is used to select a value
STOP

HF131PEN_v0501_05
Page 8
2.3. OPERATOR INFORMATION AND FUNCTIONS
In general, the F131-P will always function at Operator level. The information displayed is dependant
upon the SETUP-settings. All pulses generated by the connected flowmeter are measured by the
F131-P in the background, whichever screen refresh rate setting is chosen. After pressing a key, the
display will be updated very quickly during a 30 second period, after which it will slow-down again.
To enter a batch quantity
To change the PRESET-value, following procedure must be followed:
1) press PROG: the word "PROGRAM" will be flashing,
2) use to select the digits and to increase that value,
3) set the new PRESET-value by pressing ENTER.
Fig. 3: Example display information during programming preset value.
When data is altered but ENTER has not been pressed yet, then the alteration can still be
cancelled by waiting for 20 seconds or by pressing ENTER during three seconds: the former
value will be reinstated. The PRESET-value can be used time after time till a new value is
programmed.
Please note that alterations will only be set after ENTER has been pressed!
Batch maximum
When you program a new value which is not valid - the batch size is too large - the decrease-
signwill be displayed while you are programming; the new value will not be accepted!
Starting up the batch process
The batch process can only be started up when "READY" is displayed. The batch process is
started-up by pressing the START-key. Depending on the SETUP-settings, one or two relays
will be switched. The arrows at the display indicate if the ACTUAL-value is / was counting up
or down.
Fig. 4: Example display information during and at the end of the process.

HF131PEN_v0501_05
Page 9
Interrupting and ending the batch process
When STOP is pressed once, the batch process will be temporarily interrupted; the actual
values are not lost. At the display, the word "PAUSE" will be flashing. From this stage, the
batch process can be resumed with the START-key.
The process can be ended entirely at all times by pressing STOP twice in which case the
actual values are "lost" and the system returns to steady state: the batch can not be resumed.
Fig. 5: Example display information when interrupted.
Flowrate indication
Remark: this function might not be available: it depends on the configuration of the unit..
During batching, the actual flowrate will be displayed on the bottom-line of the display.
It depends on the configuration settings if flowrate is displayed continuously or alternating with
the preset value.
After batching, following functions are available:
Clear total
The value for total can be re-initialized. To do so, select Total and press PROG followed by
STOP - STOP. After pressing STOP once, the flashing text "PUSH STOP" is displayed.
To avoid re-initialization at this stage, press another key than STOP or wait for 20 seconds.
Re-initialization of total DOES NOT influence the accumulated total.
Display accumulated total
When the STOP-key is pressed, total and accumulated total are displayed. The accumulated
total cannot be re-initialized. The value will count up to 99,999,999,999. The unit and number
of decimals are displayed according to the configuration settings for preset.
Low-battery alarm
When the battery voltage drops, it must be replaced. At first "low-battery" will flash, but as
soon as it is displayed continuously, the battery MUST be replaced shortly after!
Only official batteries may be used, or else the guarantee will be terminated. The remaining
lifetime after the first moment of indication is generally several days up to some weeks.
Fig. 6: Example of low-battery alarm.
Alarm 01-03
When "alarm" is displayed, please consult Appendix B: problem solving.

HF131PEN_v0501_05
Page 10
3. CONFIGURATION
3.1. INTRODUCTION
This and the following chapters are exclusively meant for electricians and non-operators. In these,
an extensive description of all software settings and hardware connections are provided.
Mounting, electrical installation, start-up and maintenance of the instrument may only
be carried out by trained personnel authorized by the operator of the facility. Personnel
must read and understand this Operating Manual before carrying out its instructions.
The F131-P may only be operated by personnel who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
Ensure that the measuring system is correctly wired up according to the wiring
diagrams. The housing may only be opened by trained personnel.
Take careful notice of the " Safety rules, instructions and precautionary measures " in
the front of this manual.
3.2. PROGRAMMING SETUP-LEVEL
3.2.1. GENERAL
Configuration of the F131-P is done at SETUP-level. SETUP-level is reached by pressing the
PROG/ENTER key for 7 seconds; at which time, both arrows will be displayed. In order to return
to the operator level, PROG will have to be pressed for three seconds. Alternatively, if no keys are
pressed for 2 minutes, the unit will exit SETUP automatically.
SETUP can be reached at all times while the F131-P remains fully operational.
Note: A pass code may be required to enter SETUP. Without this pass code access to SETUP is
denied.
To enter SETUP-level:

HF131PEN_v0501_05
Page 11
Matrix structure SETUP-level:
SCROLLING THROUGH SETUP-LEVEL
Selection of function-group and function:
SETUP is divided into several function groups and functions.
Each function has a unique number, which is displayed below the word "SETUP" at the bottom of
the display. The number is a combination of two figures. The first figure indicates the function-group
and the second figure the sub-function. Additionally, each function is expressed with a keyword.
After selecting a sub-function, the next main function is selected by scrolling through all "active" sub-
functions (e.g. 1, 11, 12, 13, 14, 1, 2, 3, 31 etc.).

HF131PEN_v0501_05
Page 12
To change or select a value:
To change a value, use to select the digits and to increase that value.
To select a setting, both and can be used.
If the new value is invalid, the increase signor decrease-signwill be displayed while you are
programming.
When data is altered but ENTER is not pressed, then the alteration can still be cancelled by waiting
for 20 seconds or by pressing ENTER for three seconds: the PROG-procedure will be left
automatically and the former value reinstated.
Note: alterations will only be set after ENTER has been pressed!
To return to OPERATOR-level:
In order to return to the operator level, PROG will have to be pressed for three seconds. Also, when
no keys are pressed for 2 minutes, SETUP will be left automatically.

HF131PEN_v0501_05
Page 13
3.2.2. OVERVIEW FUNCTIONS SETUP LEVEL
SETUP FUNCTIONS AND VARIABLES
1 PRESET
11 UNIT L - m3 - kg - lb - GAL - USGAL - bbl - no unit
12 DECIMALS 0 - 1 - 2 - 3 (Ref: displayed value)
13 K-FACTOR: 0.000010 - 9,999,999
14 DECIMALS K-FACTOR 0 - 6
15 BATCH MAXIMUM X,XXX,XXX quantity
2 FLOWRATE
21 UNIT mL - L - m3 - mg - g - kg - ton - GAL - bbl - lb - cf - REV -
no unit - scf - Nm3 - NL - P
22 TIME UNIT sec - min - hour - day
23 DECIMALS 0 - 1 - 2 - 3 (Ref: displayed value)
24 K-FACTOR 0.000010 - 9,999,999
25 DECIMALS K-FACTOR 0 - 6
26 CALCULATION per 1 - 255 pulses
27 CUT-OFF 0.1 - 999.9 seconds
3 OVERRUN
31 OVERRUN disable - enable
32 TIME 0.1 - 999.9 seconds
4 DISPLAY
41 DISPLAY increase - decrease
42 FLOWRATE off - batch - toggle
5 POWER MANAGEMENT
51 LCD UPDATE fast - 1 sec - 3 sec - 15 sec - 30 sec - off
52 BATTERY MODE operational - shelf
6 FLOWMETER
61 SIGNAL npn - npn_lp - reed - reed_lp - pnp - pnp_lp - namur -
coil_hi - coil_lo - act_8.1 - act_12 - act_24
7 ANALOG
71 OUTPUT disable - enable
72 4mA / 0V 0000.000 - 9,999,999
73 20mA / 10V 0000.000 - 9,999,999
74 CUT-OFF 0.0 - 9.9%
75 TUNE MIN - 4mA / 0V 0 - 9,999
76 TUNE MAX- 20mA / 10V 0 - 9,999
77 FILTER 00 - 99
8 RELAYS
81 RELAYS 1-step / 2-step
82 PRECLOSE X,XXX,XXX quantity
83 PERIOD TIME 0 - 250
84 IMPULSE PER X,XXX,XXX quantity
85 IMPULSE ACCORDING total - batch
9 COMMUNICATION
91 SPEED / BAUDRATE 1200 - 2400 - 4800 - 9600
92 ADDRESS 1 - 255
93 MODE ASCII - rtu - off
A OTHERS
A1 TYPE / MODEL
A2 SOFTWARE VERSION
A3 SERIAL NO.
A4 PASSWORD 0000 - 9999
A5 TAGNUMBER 0000000 - 9999999

HF131PEN_v0501_05
Page 14
3.2.3. EXPLANATION OF SETUP-FUNCTIONS
1 - PRESET
MEASUREMENT UNIT
11 SETUP - 11 determines the measurement unit for preset, total,
accumulated total and pulse output. The following units can be selected:
L - m3 - kg - lb. - GAL - USGAL - bbl - _ (no unit).
Alteration of the measurement unit will have consequences for operator
and SETUP-level values.
Please note that the K-factor has to be adapted as well; the calculation is
not done automatically.
DECIMALS
12 The decimal point determines for preset, total, accumulated total and
pulse output the number of digits following the decimal point.
The following can be selected:
0000000 - 111111.1 - 22222.22 - 3333.333
K-FACTOR
13 With the K-factor, the flowmeter pulse signals are converted to a quantity.
The K-factor is based on the number of pulses generated by the
flowmeter per selected measurement unit (SETUP 11), for example per
cubic meter. The more accurate the K-factor, the more accurate the
functioning of the system will be.
Example 1: Calculating the K-factor.
Let us assume that the flowmeter generates 2.4813 pulses per
liter and the selected unit is "cubic meters / m3". A cubic meter
consists of 1000 parts of one liter which implies 2,481.3 pulses
per m3. So, the K-factor is 2,481.3. Enter for SETUP - 13:
"2481300" and for SETUP - 14 - decimals K-factor "3".
Example 2: Calculating the K-factor.
Let us assume that the flowmeter generates 6.5231 pulses per
gallon and the selected measurement unit is gallons.
So, the K-Factor is 6.5231. Enter for SETUP - 13: "6523100"
and for SETUP - 14 decimals K-factor "6".
DECIMALS K-FACTOR
14 This setting determines the number of decimals for the K-factor entered.
(SETUP 13). The following can be selected:
0 - 1 - 2 - 3 - 4 - 5 - 6
Please note that this setting influences the accuracy of the K-factor
indirectly. (i.e. the position of the decimal point and thus the value given)
This setting has NO influence on the displayed number of digits for total
(SETUP 12)!
BATCH MAXIMUM
15 This function limits the operator to enter a new preset-value which is more
as the entered batch maximum.

HF131PEN_v0501_05
Page 15
2 - FLOWRATE
The settings for preset and flowrate are entirely separate. In this way, different units of measurement
can be used for each e.g. cubic meters for total and liters for flowrate.
The display update time for flowrate is one second or more.
Note: these settings also influence the analog output.
MEASUREMENT UNIT
21 SETUP - 21 determines the measurement unit for flowrate.
The following units can be selected:
mL - L - m3 - mg - g - kg - ton - GAL - bbl - lb - cf - REV - no unit -
scf - Nm3 - NL - P
Alteration of the measurement unit will have consequences for operator
and SETUP-level values.
Please note that the K-factor has to be adapted as well; the calculation is
not done automatically.
TIME UNIT
22 The flowrate can be calculated per second (SEC), minute (MIN), hour
(HR) or day (DAY).
DECIMALS
23 This setting determines for flowrate the number of digits following the
decimal point. The following can be selected:
00000 - 1111.1 - 2222.22 - 3333.333
K-FACTOR
24 With the K-factor, the flowmeter pulse signals are converted to a flowrate.
The K-factor is based on the number of pulses generated by the
flowmeter per selected measurement unit (SETUP 21), for example per
liter. The more accurate the K-factor, the more accurate the functioning of
the system will be. For examples read SETUP 13.
DECIMALS K-FACTOR
25 This setting determines the number of decimals for the K-factor
(SETUP 24). The following can be selected:
0 - 1 - 2 - 3 - 4 - 5 - 6
Please note that this SETUP - influences the accuracy of the K-factor
indirectly.
This setting has NO influence on the displayed number of digits for
"flowrate" (SETUP 23)!
CALCULATION
26 The flowrate is calculated by measuring the time between a number of
pulses, for example 10 pulses. The more pulses the more accurate the
flowrate will be. The maximum value is 255 pulses.
Note: this setting does influence the update time for the analog output
directly (maximum update 10 times a second). If the output response is
too slow, decrease the number of pulses.
Note: the lower the number of pulses, the higher the power consumption
of the unit will be (important for battery powered applications).
Note: for low frequency applications (below 10Hz): do not program more
than 10 pulses else the update time will be very slow.
Note: for high frequency application (above 1kHz) do program a value of
50 or more pulses.
CUT-OFF TIME
27 With this setting, you determine a minimum flow requirement thresh-hold,
if during this time less than XXX-pulses (SETUP 26) are generated, the
flowrate will be displayed as zero.
The cut-off time has to be entered in seconds - maximum time is 999
seconds (about 15 minutes).

HF131PEN_v0501_05
Page 16
3 - OVERRUN
Overrun can occur at the end of the batch process, as a result of slowness of a valve / pump.
Consequently, the accuracy is less. With this function, the F131-P analyses the actual overrun
characteristic after every batch. This information is used to correct the overrun automatically.
OVERRUN
31 For an accurate overrun correction, it is necessary that the flow meter
meets certain technical demands, such as "high resolution" and shows no
"false" overrun due to a slow update time.
Do not enable this function if the flow meter does not meet these technical
demands.
OVERRUN TIME
32 The overrun characteristic of the system will be analyzed during a certain
time after the batch. In this way, false signal generated through leakage
are eliminated.
Enter here the expected time needed by the system to stop a batch. It is
advisable to provide extra time in order to avoid an incorrect overrun
correction or false leakage alarms.
Note that the next batch can only be started after elapsing of this overrun
time!
The minimum overrun time is 0.1 second, maximum 999.9 seconds.
4 - DISPLAY
DISPLAY
41 The large 17mm digits can be set to display the actual batched quantity
(increase) OR to display the remaining quantity to be batched (decrease).
FLOWRATE
42 This setting determines if the calculated flowrate will be displayed. Three
setting can be set:
off: flowrate will not be displayed
batch: after pressing start, the flowrate will be displayed till the end of
the batch. In this case, we advise you to set setting 41 to "decrease"
toggle: flowrate is displayed alternating with the preset value.
5 - POWER MANAGEMENT
When used with the internal battery option, the user can expect reliable measurement over a long
period of time. The F131-P has several smart power management functions to extend the battery life
time significantly. Two of these functions can be set:
LCD NEW
51 The calculation of the display-information influences the power
consumption significantly. When the application does not require a fast
display update, it is strongly advised to select a slow refresh rate.
Please understand that NO information will be lost; every pulse will be
counted and the output signals will be generated in the normal way.
The following can be selected:
Fast - 1 sec - 3 sec - 15 sec - 30 sec - off.
Example 3: Battery life-time
battery life-time with a coil pick-up, 1KHz. pulses and FAST
update: about 2 years.
battery life-time with a coil pick-up, 1KHz. pulses and 1 sec
update: about 5 years.
Note: after a button has been pressed by the operator - the display
refresh rate will always switch to FAST for 30 seconds. When "OFF" is
selected, the display will be switched off after 30 seconds and will be
switched on as soon as a button has been pressed.
BATTERY-MODE
52 The unit has two modes: operational or shelf.
After "shelf" has been selected, the unit can be stored for several years; it
will not count pulses, the display is switched off but all settings and totals
are stored. In this mode, power consumption is extremely low.
To wake up the unit again, press the SELECT-key twice.

HF131PEN_v0501_05
Page 17
6 - FLOWMETER
SIGNAL
61 The F131-P is able to handle several types of input signal. The type of
flowmeter pickup / signal is selected with SETUP 61.
Note: The selections "active pulse" offer a detection level of 50% of the
supply voltage.
Read also par. 4.4.3. Flowmeter input terminal 09-11.
TYPE OF SIGNAL EXPLANATION RESISTANCE FREQ./MV REMARK
NPN NPN input 100K
pull-up 6 kHz. (open collector)
NPN - LP NPN input
with low pass filter 100K pull-up 2.2 kHz. (open collector)
less sensitive
REED Reed-switch input 1M
pull-up 1.2 kHz.
REED - LP Reed-switch input
with low pass filter 1M pull-up 120 Hz. Less sensitive
PNP PNP input 100K
pull-down 6 kHz.
PNP - LP PNP input
with low pass filter 100K pull-down 700 Hz. Less sensitive
NAMUR Namur input 820 Ohm
pull-down 4 kHz. External power
required
COIL HI High sensitive coil input - 20mV
p.t.p. Sensitive for disturbance!
COIL LO Low sensitive coil input - 90mV
p.t.p. Normal sensitivity
ACT_8.1 Active pulse input
8.1 VDC 3K9 10KHz.
External power
required
ACT_12 Active pulse input
12 VDC 4K 10KHz.
External power
required
ACT_24 Active pulse input
24 VDC 3K 10KHz.
External power
required

HF131PEN_v0501_05
Page 18
7 - ANALOG OUTPUT
A linear 4-20mA signal (option AB: 0-20mA or option AU: 0-10V) output signal is generated
according to the flowrate with a 10 bits resolution. The settings for flowrate (SETUP - 2) directly
influence the analog output.
Note: When the analog output is not used, please make sure that setting 71 is disabled, or else the
battery life time will be reduced significantly!
When a power supply is available but the output is disabled, a 3.5mA signal will be generated.
The relationship between rate and analog output is set with the following functions:
DISABLE / ENABLE
71 The D/A converter has a relatively high power consumption. If the analog
output is not being used, select "disable" to switch-off the converter.
For more information read par. 4.4.3.
MINIMUM FLOWRATE
72 Enter here the flowrate at which the output should generate a 4mA signal
(or 0mA / 0V) - in most applications at flowrate "zero".
The number of decimals displayed depend upon SETUP 23.
The time and measuring units (L/min for example) are dependant upon
SETUP 21 and 22 but are not displayed.
MAXIMUM FLOWRATE
73 Enter here the flowrate at which the output should generate a 20mA (or
10V) - in most applications at maximum flow.
The number of decimals displayed depend upon SETUP 23.
The time and measuring units (L/min for example) are dependant upon
SETUP 21 and 22 but can not be displayed.
CUT-OFF
74 To ignore leakage of the flow for example, a low flow cut-off can be set as
a percentage of the full range of 16mA (or 20mA / 10V). When the flow is
less than the required rate, the current will be 4mA.
Examples:
4MA
(SETUP 72) 20MA (SETUP 73) CUT-OFF (SETUP 74) REQUIRED RATE OUTPUT
0 L/min 100 L/min 2% (100-0)*2% = 2.0 L/min 4+(16*2%) = 4.32mA
20 L/min 800 L/min 3.5% (800-20)*3.5%= 27.3 L/min 4+(16*3.5%)=4.56mA
TUNE MIN / 4MA
75 The initial minimum analog output value is 4mA (or 0mA / 0V). However,
this value might differ slightly due to external influences such as
temperature for example. The 4mA value (or 0mA / 0V) can be tuned
precisely with this setting.
Before tuning the signal, be sure that the analog signal is not
being used for any application!
After pressing PROG, the current will be about 4mA (or 0mA / 0V). The
current can be increased/decreased with the arrow-keys and is directly
active.
Press ENTER to store the new value.
TUNE MAX / 20MA
76 The initial maximum analog output value is 20mA (or 10V). However, this
value might differ slightly due to external influences such as temperature
for example. The 20mA value (or 10V) can be tuned precisely with this
setting.
Before tuning the signal, be sure that the analog signal is not
being used for any application!
After pressing PROG, the current will be about 20mA. The current can be
increased/decreased with the arrow-keys and is directly active. Press
ENTER to store the new value.
Continued next page >>>

HF131PEN_v0501_05
Page 19
7 - ANALOG OUTPUT (CONTINUED)
FILTER
77 This function is used to stabilize the analog output signal.
The output value is updated every 0.1 second. With the help of this digital
filter a more stable but less precise reading can be obtained.
The filter principal is based on three input values: the filter level (01-99),
the last analog output value and the last average value. The higher the
filter level, the longer the response time on a value change will be.
Below, several filter levels with their response times are indicated:
FILTER VALUE RESPONSE TIME ON STEP CHANGE OF ANALOG VALUE.
TIME IN SECONDS
50%INFLUENCE 75% INFLUENCE 90% INFLUENCE 99%INFLUENCE
01 filter disabled filter disabled filter disabled filter disabled
02 0.1 second 0.2 second 0.4 second 0.7 second
03 0.2 second 0.4 second 0.6 second 1.2 seconds
05 0.4 second 0.7 second 1.1 seconds 2.1 seconds
10 0.7 second 1.4 seconds 2.2 seconds 4.4 seconds
20 1.4 seconds 2.8 seconds 4.5 seconds 9.0 seconds
30 2.1 seconds 4 seconds 7 seconds 14 seconds
50 3.5 seconds 7 seconds 11 seconds 23 seconds
75 5.2 seconds 10 seconds 17 seconds 34 seconds
99 6.9 seconds 14 seconds 23 seconds 45 seconds

HF131PEN_v0501_05
Page 20
8- RELAY OUTPUT
Two one open-collector outputs (Optional: mechanic relays or active outputs) are available to control
relays or small valves (max. 50VDC – 300mA).
Relay 2 can also be used as pulse output according the batch total (actual) or accumulated total.
Please note: if the communication option has been supplied, the pulse output functions 83, 84 and
85 are not available.
1-STEP / 2-STEP
81 With this setting, the function of relay is Select "2-step" to executed batches with a two-stage valve.
Select “1-step” to be able to use relay 2 as pulse output relay.
PRECLOSE QUANTITY
82 According to the setting 81 - 2-step, relay two will be used to control a
valve for the batch process.
If the product is batched in two steps, the switch-off-moment for relay 2
has to be set. The switch moment is based on the remaining quantity
before the end of batch.
If the preclose quantity is set to zero, it will switch simultaneously with
relay 1.
PERIOD TIME
PULSE OUTPUT
83
According to the setting 81 - 1-step, relay 2 can be used as a scaled pulse
output.
The period time determines the time that the transistor or relay will be
switched; in other words the pulse length. The minimum time between the
pulses is as long as the period time.
One period is approx. 7.8 msec. If the value selected is “zero”, the pulse
output is disabled. The maximum value is 255 periods.
Note: If the frequency should go out of range - when the flowrate
increases for example - an internal buffer will be used to "store the missed
pulses": As soon as the flowrate reduces again, the buffer will be
"emptied".
It might be that pulses will be missed due to a buffer-overflow, so it is
advised to program this setting within it's range
NUMBER OF PERIODS PERIOD TIME MAX.FREQUENCY
0 disabled disabled
1 0,0078 seconds 64 Hz.
2 0,0156 seconds 32 Hz.
3 0,0234 seconds 21 Hz.
64 0,5000 seconds 1 Hz.
255 1,9922 seconds 0.25 Hz.
PULSE PER
84 According to the measurement unit settings for preset, a scaled pulse will
be generated every X-quantity. Enter this quantity here while taking the
displayed decimal position and measuring unit into account.
PULSE ACCORDING
ACC. TOTAL / BATCH
85
With this function, it is determined if a pulse will be generated according
the quantity batched or according accumulated total.
With setting "batch" the pulse generator will be set to zero when a new
batch is started up.