Fluidwell F130-P User manual

F130-P
BATCH CONTROLLER
two-stage control and pulse output
Signal input flowmeter: pulse, Namur and coil
External controls: start and stop
Digital outputs: two control outputs for two stage control, or
one control output and pulse output
Options: Intrinsically safe, Modbus communication
F-Series - Field mounted indicators for safe and hazardous areas.
More info: www.fluidwell.com/fseries

Page 2
FW_F130-P_M_v2201-01_EN.docx
SAFETY INSTRUCTIONS
•Any responsibility is lapsed if the instructions and procedures as described in this manual
are not followed.
•LIFE SUPPORT APPLICATIONS: The F130-P is not designed for use in life support
appliances, devices, or systems where malfunction of the product can reasonably be
expected to result in a personal injury. Customers using or selling these products for use
in such applications do so at their own risk and agree to fully indemnify the manufacturer
and supplier for any damages resulting from such improper use or sale.
•Electro static discharge does inflict irreparable damage to electronics! Before installing or
opening the F130-P, the installer has to discharge himself by touching a well-grounded
object.
•The F130-P must be installed in accordance with the EMC guidelines (Electro Magnetic
Compatibility).
•Connect a proper grounding to the metal enclosure as indicated if the F130-P has an
incoming power or signal line which carries a hazardous live voltage.
The Protective Earth (PE) wire may never be disconnected or removed.
•Intrinsically Safe applications: follow the instructions as mentioned in Chapter 5.
Certificates and related documents are available on our website or from your distributor.
DISPOSAL OF ELECTRONIC WASTE
•The WEEE Directive requires the recycling of disposed electrical and electronic
equipment in the European Union. When the WEEE Directive does not apply to your
region, we support its policy and ask you to be aware on how to dispose of this product.
•The crossed out wheelie bin symbol as illustrated and found on our products tells that
this product shall not be disposed of into the general waste system or into a landfill.
•At the end of its life, equipment shall be disposed of according to the local regulations
regarding waste of the electrical and the electronic equipment.
•
helpdesk for information on the product disposal.
SAFETY RULES AND PRECAUTIONARY MEASURES
•The manufacturer accepts no responsibility whatsoever if the following safety rules and
precautions, instructions and the procedures as described in this manual are not
followed.
•Modifications of the F130-P implemented without preceding written consent from the
manufacturer, will result in the immediate termination of product liability and warranty
period.
•Mounting, electrical installation, start-up and maintenance of this device may only be
carried out by trained persons authorized by the operator of the facility. Persons must
read and understand this manual before carrying out its instructions.
•This device may only be operated by persons who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Check the mains voltage and information on the manufacturer's plate before installing the
F130-P.
•Check all connections, settings and technical specifications of the various peripheral
devices with the F130-P supplied.
•Open the enclosure only if all leads are free of potential.
•Never touch the electronic components (ESD sensitivity).
•Never expose the system to heavier conditions than allowed according to the
classification of the enclosure (see manufacture's plate and chapter 4.2.).
•If the operator detects errors or dangers, or disagrees with the safety precautions taken,
he should inform the owner or principal responsible.
•The local labor and safety laws and regulations must be adhered to.

Page 3
FW_F130-P_M_v2201-01_EN.docx
ABOUT THE MANUAL
This manual is divided into two main sections:
▪The daily use of the unit is described in chapter 2 "Operation". These instructions are meant for
users.
▪The following chapters and appendices are exclusively meant for electricians/technicians. These
provide a detailed description of all software settings and hardware installation guidance.
This manual describes the standard unit as well as the available options. For additional information,
please contact your supplier.
A hazardous situation may occur if the F130-P is not used for the purpose it was designed for
or is used incorrectly. Please carefully note the information in this manual indicated by the
pictograms:
A "warning !" indicates actions or procedures which, if not performed correctly, may lead to
personal injury, a safety hazard or damage of the F130-P or connected instruments.
A "caution !" indicates actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the F130-P or connected instruments.
A "note !" indicates actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned.
WARRANTY AND TECHNICAL SUPPORT
For warranty and technical support for your products, please contact your supplier, visit our internet
site www.fluidwell.com or contact us at [e-mail].
Hardware version : 03.01.xx
Software version : 03.01.xx
Manual : FW_F130-P_M_v2201-01_EN.docx
© Copyright 2023 : Fluidwell B.V. - the Netherlands
Information in this manual is subject to change without prior notice. The
manufacturer is not responsible for mistakes in this material or for incidental
damage caused as a direct or indirect result of the delivery, performance or
use of this material.
© All rights reserved. No parts of this publication may be reproduced or used
in any form or by any means without written permission of your supplier.

Page 4
FW_F130-P_M_v2201-01_EN.docx
TABLE OF CONTENTS
SAFETY INSTRUCTIONS....................................................................................................................................2
DISPOSAL OF ELECTRONIC WASTE................................................................................................................2
SAFETY RULES AND PRECAUTIONARY MEASURES.....................................................................................2
ABOUT THE MANUAL.........................................................................................................................................3
WARRANTY AND TECHNICAL SUPPORT.........................................................................................................3
TABLE OF CONTENTS........................................................................................................................................4
1INTRODUCTION.....................................................................................................................................6
1.1 System description of the F130-P............................................................................................6
2OPERATIONAL......................................................................................................................................8
2.1 General information .................................................................................................................8
2.2 Control panel............................................................................................................................8
2.3 Operator information and functions .........................................................................................8
3CONFIGURATION................................................................................................................................11
3.1 Introduction ............................................................................................................................11
3.2 Programming SETUP-level....................................................................................................11
3.2.1 Entering SETUP-level............................................................................................................11
3.2.2 Navigating through SETUP-level...........................................................................................11
3.2.3 Programming sequence.........................................................................................................12
3.2.4 Returning to OPERATOR-level .............................................................................................13
3.3 Configuration settings............................................................................................................13
3.3.1 Setup menu Settings...........................................................................................................13
3.3.2 menu 1 - PRESET .................................................................................................................14
3.3.3 menu 2 - Overrun...................................................................................................................15
3.3.4 menu 3 - Alarm ......................................................................................................................15
3.3.5 menu 4 - Display....................................................................................................................15
3.3.6 menu 5 - Power management ...............................................................................................15
3.3.7 menu 6 - Flowmeter...............................................................................................................16
3.3.8 menu 7 - Relay output............................................................................................................16
3.3.9 menu 8 - Communication (OPTION) .....................................................................................17
3.3.10 menu 9 - Others.....................................................................................................................17
4INSTALLATION....................................................................................................................................18
4.1 General directions..................................................................................................................18
4.2 installation / surrounding conditions.......................................................................................18
4.3 Handling the F-Series Enclosure...........................................................................................19
4.3.1 Identification...........................................................................................................................19
4.3.2 Opening / removing the cover................................................................................................20
4.3.3 Closing / replacing the cover .................................................................................................20
4.4 Mechanical installation...........................................................................................................21
4.4.1 Dimensions Aluminum and stainless steel enclosures.......................................................21
4.4.2 Dimensions Non-metallic enclosures..................................................................................22
4.4.3 Mounting 23
4.5 Electrical installation ..............................................................................................................24
4.5.1 Electrical safety......................................................................................................................24
4.5.2 Protective Earth (PE) connections.........................................................................................24
4.5.3 Field wiring connections.........................................................................................................25
4.5.4 Power supply wiring...............................................................................................................25
4.5.5 Sensor supply ........................................................................................................................26
4.6 Terminal connectors ..............................................................................................................27
4.6.1 Terminal 00-02: Power supply...............................................................................................27
4.6.2 Terminal 03-04: control or pulse output R2 ...........................................................................28
4.6.3 Terminal 05-06: control output R1 .........................................................................................28
4.6.4 Terminal 09-11: Flowmeter input...........................................................................................29
4.6.5 Terminal 12-13: external START...........................................................................................31
4.6.6 Terminal 15-16: external STOP.............................................................................................32
4.6.7 Terminal 26-31: Type CB / CH / CI - Communication (option).............................................33
5INTRINSICALLY SAFE APPLICATIONS.............................................................................................34
5.1 Identification...........................................................................................................................34

Page 5
FW_F130-P_M_v2201-01_EN.docx
5.2 Electrical installation in hazardous area................................................................................ 35
5.2.1 General information and instructions..................................................................................... 35
5.2.2 Installations based on ATEX or IECEx certificate ................................................................. 36
5.2.3 Electrical data Annex 1....................................................................................................... 37
5.2.4 Power supply wiring............................................................................................................... 39
5.2.5 Sensor supply........................................................................................................................ 39
5.3 Terminal connectors Intrinsically safe applications TYPE XI............................................. 40
5.3.1 Terminal 26-29: Type CT - Communication.......................................................................... 40
5.4 Configuration examples......................................................................................................... 41
6MAINTENANCE................................................................................................................................... 43
6.1 General directions ................................................................................................................. 43
6.2 Repair.................................................................................................................................... 43
6.3 Battery replacement instructions........................................................................................... 44
6.3.1 Safety instructions ................................................................................................................. 44
6.3.2 Replace the battery ............................................................................................................... 45
6.3.3 Disposal of batteries.............................................................................................................. 45
APPENDIX A. TECHNICAL SPECIFICATION .............................................................................................. 46
APPENDIX B PROBLEM SOLVING............................................................................................................. 49
APPENDIX C. COMMUNICATION VARIABLES........................................................................................... 50
APPENDIX D. DECLARATION OF CONFORMITY....................................................................................... 53
INDEX OF THIS MANUAL................................................................................................................................. 54
LIST OF FIGURES IN THIS MANUAL............................................................................................................... 55

Page 6
1 INTRODUCTION
1.1 SYSTEM DESCRIPTION OF THE F130-P
Functions and features
The batch controller model F130-P is a microprocessor driven instrument designed for batching and
filling of small up to large quantities as well as displaying the flow rate, the total and the accumulated
total. This product has been designed with a focus on:
▪ultra-low power consumption to allow long-life battery powered applications (type PB/PC);
▪intrinsic safety for use in hazardous applications (type XI);
▪several mounting possibilities with aluminum or GRP enclosures for harsh industrial
surroundings;
▪ability to process all types of flowmeter signals;
Flowmeter input
This manual describes the unit with a pulse input from the flowmeter.
One flowmeter with a passive or active pulse, Namur or sine wave (coil) signal output can be
connected to the F130-P. To power the sensor, several options are available.
Standard outputs
▪Two passive transistor or relay outputs: for two- or one stage control with pulse output.
▪Pulse output to transmit a pulse that represents a totalized quantity as programmed.
Fig. 1: Typical application
Configuration of the F130-P
The F130-P is designed for use in many types of applications. For that reason, a setup menu is
available to program the F130-P according to your specific requirements.

Page 7
FW_F130-P_M_v2201-01_EN.docx
The setup includes several important features, such as K-Factors, engineering units, signal
selection, power management (to extend battery life-time), etc. All settings are stored in a non-
volatile memory and therefore kept in the event of a power failure or an exhausted battery.
Display information
The unit has a LCD with (optional) backlight to show the process information, status and alarm
messages. The display refresh rate is programmed in the setup menu.
At a key press, the display refresh rate will switch to FAST for 30 seconds. When 'OFF' is selected,
the display goes off after 30 seconds after the last key press. The display temporarily comes on after
a key press.
A backup of the total and accumulated total in EEPROM memory is made every minute.
Options
The following options are available: full Modbus communication RS232/485/TTL (also battery
powered), intrinsic safety, mechanical relay or active output, power- and sensor-supply options,
panel-mount, wall-mount and weather-proof enclosures, flame proof enclosure and LED backlight.

Page 8
FW_F130-P_M_v2201-01_EN.docx
2 OPERATIONAL
2.1 GENERAL INFORMATION
This chapter describes the daily use of the F130-P. This instruction is meant for users / operators.
•This device may only be operated by persons who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Take careful notice of the "Safety rules, instructions and precautionary measures" in the
front of this manual.
2.2 CONTROL PANEL
The control panel has three keys. The following keys are available:
Fig. 2: Control panel.
Functions of the keys
This key is used to program and save new values or settings.
The PROG/ENTER key is also used to gain access to the setup menu (read
chapter 3).
This key is used to START the batch process.
The START/key is also used to increase a value after the PROG/ENTER key has
been pressed (read chapter 3).
This key is used to pause or stop the batch process. When the batch process is
stopped, it cannot be continued. The STOP/key is also used to select the total and
the accumulated total.
The STOP/key is also used to select a digit or an option after the PROG/ENTER
key has been pressed (read chapter 3).
2.3 OPERATOR INFORMATION AND FUNCTIONS
In general, the F130-P operates in the operator mode. The shown information depends on the
settings which are made in the setup menu.
The signal from the connected sensor is processed by the F130-P in the background, independent
from the selected display refresh rate.
Fig. 3: Example of display information during process.
▪To enter a batch quantity (change the preset)
You can only change the preset when the READY indicator is on.
1. Press the PROG/ENTER key until the PROGRAM indictor starts to blink.
2. Use the START/and STOP/key to change the value.
3. Momentarily, press the PROG/ENTER key to confirm the new preset.

Page 9
FW_F130-P_M_v2201-01_EN.docx
Fig. 4: Program preset value (typical).
When data is altered but ENTER has not been pressed yet, then the alteration can still be
cancelled by waiting for 20 seconds or by pressing ENTER during three seconds: the former
value will be reinstated. The PRESET-value can be used time after time till a new value is
programmed.
Changes are only saved when you press the PROG/ENTER key.
▪Leading zero
The amount of leading zeros is dependent on the batch maximum setting. In this menu the
leading zeros will show. When you confirm the selection with the PROG/ENTER key, the F130-P
will hide the leading zeros in the operational preset menu.
It is not possible to enter a preset value which exceeds the batch maximum setting. E.g. if the
batch maximum is set to 20000, it will not be possible to set 21000. If you want to preset
21000, you must change the batch maximum setting.
Fig. 5: Leading zero (typical).
▪Batch maximum/minimum
When you program a new value which is not valid, the decrease-sign (batch too big, program
a smaller batch) or the increase-sign (batch to small, program a bigger batch) will show.
▪To start the batch process
The batch process can only be started when "READY" is shown. The batch process is started by
pressing the START/key. Depending on the SETUP-settings, one or two relays will be
switched. The arrows at the display indicate if the ACTUAL-value is counting up or down.
▪To interrupt or to stop the batch process
When the STOP/key is pressed once, the batch process is paused; the actual values are not
lost. At the display, the word "PAUSE" blinks. In this case the, the batch process can be resumed
with the START/key.
When the STOP/key is pressed two times, the batch process is stopped completely. In this
case the actual values are "lost" and the system returns to steady state: the batch process
cannot be resumed.
Fig. 6: Process paused (typical).

Page 10
FW_F130-P_M_v2201-01_EN.docx
▪Clear batch total
The value for total can be reset. To do so, select Total and press PROG followed by STOP -
STOP. After pressing the STOP/key once, the flashing text "PUSH STOP" is shown. To avoid
a reset at this stage, press another key than the STOP/key or wait for 20 seconds.
The reset of total DOES NOT influence the accumulated total.
▪Display accumulated total
When the STOP/key is pressed, total and accumulated total are shown. The accumulated total
cannot be reset. The value will count up to 99,999,999,999. The unit and number of decimals are
shown according to the configuration settings for total.
▪Low-battery alarm
When the battery voltage drops, the "low-battery" icon will be displayed continuously. The battery
MUST be replaced shortly after!
The remaining lifetime after the first moment of indication is generally several days up to some
weeks. See paragraph 6.3 for further information on battery replacement.
Fig. 7: Example of low-battery alarm.
▪No-flow alarm
The F130-P offers a no-flow monitoring feature: When the flowmeter does not generate a signal
during a certain (preset) time period, the F130-P will shut-off the control output(s) and bring the
batch controller in alarm status. 
is shown. Press the STOP/
stays on. Now you can cancel or continue the batch (after you have solved the possible problem).
▪Alarm
When the alarm indicator is shown, refer to Appendix B: Problem Solving.

Page 11
FW_F130-P_M_v2201-01_EN.docx
3 CONFIGURATION
3.1 INTRODUCTION
This and the following chapters are exclusively meant for electricians and non-operators. In these,
an extensive description of all software settings and hardware connections are provided.
•Mounting, electrical installation, start-up and maintenance of this device may only be
carried out by trained persons authorized by the operator of the facility. Persons must
read and understand this manual before carrying out its instructions.
•This device may only be operated by persons who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Make sure, the measuring system is correctly wired up according to the wiring diagrams.
Protection against accidental contact is no longer assured when the enclosure cover is
removed or the panel cabinet has been opened (danger from electrical shock). The
enclosure may only be opened by trained persons authorized by the operator of the
facility.
•Take careful notice of the "Safety rules, instructions and precautionary measures" in the
front of this manual.
3.2 PROGRAMMING SETUP-LEVEL
Changing the settings of the F130-P may have an influence on the current operation of the
device, even when SETUP-level is still active.
Make sure that the unit is not being used for any application when altering the settings.
3.2.1 ENTERING SETUP-LEVEL
Configuration of the F130-P is done at SETUP-level, which can be reached at all times while the
F130-P remains fully operational. At SETUP-level the display will deactivate the RUN indicator and
activate the SETUP indicator.
Use the control panel to access SETUP-level
PROG-key
To enter SETUP-level, press the PROG-key for 7 seconds at OPERATOR-level.
During this time, the symbols  will be displayed.
When SETUP-level is entered, a password might be required to continue. You can
enter the password by following the procedure for programming values as described in
the following paragraphs.
A password may be required to enter SETUP.
Without this password access to SETUP is denied.
3.2.2 NAVIGATING THROUGH SETUP-LEVEL
Each function has a unique menu-number, which is displayed below the SETUP indicator at the
bottom of the display. The menu-number is a combination of two figures, e.g. 1.2. The first number
indicates the function-group and the second number indicates the function. Additionally, each
function and function-group is expressed with a keyword.
Fig. 8: SETUP matrix structure
1.1
1.2
2.1.
2.1
1.3
2.2
3.1
3.
FUNCTION GROUP
FUNCTION
FW-4100-000001-001-EN

Page 12
FW_F130-P_M_v2201-01_EN.docx
Use the control panel to navigate through SETUP-level
PROG-key
When a function is selected, this key is used to start the programming sequence.
When only a function group is selected (and no function), this key is used to scroll
back a function group (e.g. 3 →2 →1 →3).
START-key
This key is used to select the next function in the list (e.g. 1 →1.1 →1.2 →1). When
the top of the list is reached, it will wrap around and return to the function group
selection.
STOP-key
This key is used to select the previous function in the list (e.g. 1.2 →1.1 →1 →2).
When the bottom of the list is reached, it will return to the function group selection.
When only a function group is selected (and no function), this key is used to scroll to
the next function group. (e.g. 1 →2 →3 →1).
3.2.3 PROGRAMMING SEQUENCE
After selecting a function at SETUP-level, a new value can be programmed using the control panel.
A function either contains a value (a number with optionally a decimal point, e.g. 123.45) or a list
with items (e.g. Disable Enable).
For each function that needs to change, navigate to that function and follow the steps indicated
below. During the programming sequence, the display will deactivate the SETUP indicator and
activate the PROGRAM indicator.
When programming new values, alterations will only be set after the PROG-key has been
pressed to confirm the new value! (STEP 3)
Step 1: Starting the programming sequence
PROG-key
When a function is selected at SETUP-level, this key is used to start the programming
sequence.
Step 2a: Changing a value
START-key
This key is used to increment the selected digit.
When the entered value is out of range, the increase sign or decrease-sign will
be displayed while you are programming. If this value is confirmed by pressing the
PROG-key, the value will be brought within a valid range automatically.
STOP-key
This key is used to select the next digit. If a decimal point can be set, this will be
included in the sequence as well (e.g. [decimal point] →digit 1 →digit 2→digit 3 →
[decimal point].
START-key + STOP-key
The combination of the START-key and STOP-key is used to select a negative value.
When a value can also be entered as a negative number, pressing the START-key
and STOP-
Step 2b: Changing the selected item in a list
START-key
This key is used to select the next item in the list (e.g. Disable →Enable).
At the end of the list, the selection will wrap around to the first selection.

Page 13
FW_F130-P_M_v2201-01_EN.docx
STOP-key
This key is used to select the previous item in the list (e.g. Enable →Disable ).
At the bottom of the list, the selection will wrap around to the last selection.
Step 3: Finishing the programming sequence
PROG-key
During the programming sequence, this key is used to confirm the new value and
return to SETUP-level. To cancel the operation, either press the PROG-key for 3
seconds or wait for 20 seconds: the programming sequence is cancelled and the
former value is reinstated.
3.2.4 RETURNING TO OPERATOR-LEVEL
When all settings are configured correctly, the unit can be returned to OPERATE-level.
Please keep a record of all settings for later reference.
Use the control panel to return to OPERATE-level
PROG-key
In order to return to the operator level, press the PROG-key for three seconds.
When no keys are pressed for 2 minutes, SETUP-level will be left automatically.
3.3 CONFIGURATION SETTINGS
All settings of the F130-P can be set via the control panel.
The following paragraphs give a detailed description of each setting.
3.3.1 SETUP MENU SETTINGS
SETUP FUNCTIONS AND VARIABLES
1
PRESET
1.1
UNIT
L; m3; kg; lb; GAL; USGAL; bbl; no unit
1.2
DECIMALS
0000000; 111111.1; 22222.22; 3333.333
1.3
K-FACTOR
0.000010 - 9999999
1.4
DECIMALS K-FACTOR
0 - 6
1.5
BATCH-MIN
0000000 - 9999999
1.6
BATCH-MAX
0000000 - 9999999
2
OVERRUN
2.1
OVERRUN
disable; enable
2.2
TIME
0.1 - 999.9 seconds
3
ALARM
3.1
NO FLOW
disable; enable
3.2
TIME
0.1 - 999.9 seconds
4
DISPLAY
4.1
DISPLAY
increase; decrease
4.2
LIGHT
0% (off); 20%; 40%; 60%;- 80%; 100% (full brightness)
5
POWER MANAGEMENT
5.1
LCD NEW
fast; 1 sec; 3 sec; 15 sec; 30 sec; off
5.2
BATTERY MODE
operational; shelf
6
FLOWMETER
6.1
SIGNAL
npn; npn-lp; reed; reed-lp; pnp; pnp-lp; namur; coil-hi; coil-lo; 8-1 DC; 12 DC; 24 DC
7
RELAYS
7.1
RELAYS
1-step; 2-step
7.2
PRECLOSE
0000.000 - 9999999
7.3
WIDTH
0.000 - 9.999 sec (0 = off)
7.4
DECIMALS
0000000; 111111.1; 22222.22; 3333.333

Page 14
FW_F130-P_M_v2201-01_EN.docx
7.5
AMOUNT
0000.001 –9999999
7.6
PULSE
total; batch
8
COMMUNICATION
8.1
SPEED
1200; 2400; 4800; 9600
8.2
ADDRESS
1 - 255
8.3
MODE
bus-rtu; bus-asc; off
9
OTHERS
9.1
MODEL
F130-P
9.2
SOFTWARE VERSION
03.01.xx
9.3
SERIAL NO.
nnnnnnn
9.4
PASSWORD
0000 - 9999
9.5
TAG-NR
0000000 - 9999999
3.3.2 MENU 1 - PRESET
1
PRESET
1.1
UNIT
This setting is used to select the engineering unit for the indication of
the batch total, the accumulated total and the pulse output.
When you change the engineering unit, you must recalculate and
reprogram the K-factor for the (accumulated) total. When you
recalculate and reprogram the K-Factor, the history for (accumulated)
batch total is not correct anymore, because the (accumulated) batch
total is not recalculated. For future reference, best practice is to make
a note of the accumulated total before you program the recalculated
K-Factor.
1.2
DECIMALS
This setting is used to set the amount of digits behind the decimal
point for the (accumulated) total indication.
1.3
K-FACTOR
This setting is used to set the K-Factor for the total. With the K-Factor,
the flowmeter pulse signals are converted to a quantity. The K-Factor
is based on the number of pulses generated by the flowmeter per
selected engineering unit, for example per m3. A more accurate K-
Factor (more decimals, as set in decimals K-Factor) allows for a more
accurate operation of the system.
Example 1: Calculating the K-Factor.
The flowmeter generates 2.4813 pulses per liter and the selected unit
is m3. A cubic meter consists of 1000 liter which gives 2.4813
pulses*1000 liter=2481.3 pulses per m3. So, the K-Factor is 2481.3.
Enter for the Flowmeter K-Factor: 24813 and for the flowmeter K-
Factor decimals: 1.
Example 2: Calculating the K-Factor.
The flowmeter generates 6.5231 pulses per gallon and the selected
engineering unit is gallons. So, the K-Factor is 6.5231. Enter for the
Flowmeter K-Factor: 65231 and for the Flowmeter K-Factor decimals:
4.
When you recalculate and reprogram a new K-Factor, the history for
(accumulated) batch total is not correct anymore, because the
(accumulated) batch total is not recalculated. For future reference,
best practice is to make a note of the accumulated total before you
program the recalculated K-Factor.
1.4
DECIMALS K-FACTOR
This setting is used to set the amount of digits behind the decimal
point for the K-Factor.
1.5
BATCH MINIMUM
This setting is used to set the lower limit for a batch volume. An
operator cannot set a batch volume which is beyond the lower limit.
1.6
BATCH MAXIMUM
This setting is used to set the upper limit for a batch volume. An
operator cannot set a batch volume which is beyond the upper limit.

Page 15
FW_F130-P_M_v2201-01_EN.docx
3.3.3 MENU 2 - OVERRUN
Due to system parameters which are beyond the settings of the batch controller, an overrun can
occur at the end of a batch. The batch controller analyzes the overrun volume and automatically
corrects the volume each time after each batch (self learning).
2
OVERRUN
2.1
OVERRUN
For an accurate overrun correction, it is necessary that the flowmeter
meets certain technical demands, such as "high resolution" and shows
no "false" overrun due to a slow update time. Do not enable this
function if the flow meter is not compatible to this function.
2.2
TIME
The overrun characteristic of the system will be analyzed during a
certain time after the batch relay has been de-energized. In this way,
false signal generated through leakage are eliminated. Enter here the
expected time needed by the system to stop a batch. It is advisable to
provide extra time in order to avoid an incorrect overrun correction or
false leakage alarms.
The next batch can only be started after the overrun time is completed!
3.3.4 MENU 3 - ALARM
The F130-P offers a no-flow monitoring feature: When the flowmeter does not generate a signal
during a certain (preset) time period, the F130-P will shut-off the control output(s) and bring the
batch controller in alarm status.
3
ALARM
3.1
NO-FLOW
This setting is used to program the behavior of the no-flow alarm. When
the flow rate is zero, it is possible to ignore or disable the no-flow
monitoring.
3.2
TIME
This setting is used to set a delay time for the related alarm. When the
alarm condition is still valid after the delay time, an alarm is given.
3.3.5 MENU 4 - DISPLAY
4
DISPLAY
4.1
DISPLAY
This setting is used to set the behavior of the counter during a batch
process: count down (quantity to do) or count up (quantity done).
4.2
LIGHT
The backlight brightness can be adjusted from 0% (off) to 100% (full
brightness) in steps of 20%.
3.3.6 MENU 5 - POWER MANAGEMENT
When used with the internal battery option (type PB/PC), the user can expect reliable measurement
over a long period of time. The F130-P has several smart power management functions to extend
the battery life time significantly. Two of these functions can be set.
5
POWER MANAGEMENT
5.1
LCD NEW
The calculation of the display-information influences the power
consumption significantly. When the application does not require a fast
display refresh rate, it is strongly advised to select a slow refresh rate.
Please understand that NO information will be lost; every pulse will be
counted and the output signals will be generated in the normal way.
At a key press, the display refresh rate will switch to FAST for 30
seconds. When 'OFF' is selected, the display goes off after 30 seconds
after the last key press. The display temporarily comes on after a key
press.
Example battery life-time with a coil pick-up:
•1kHz pulse and FAST update: about 2 years;
•1kHz pulse and 1 sec update: about 5 years.

Page 16
FW_F130-P_M_v2201-01_EN.docx
5.2
BATTERY MODE
The F130-P has two modes: operational or shelf.
After "shelf" has been selected, the F130-P can be stored for several
years; it will not process the sensor signal; the display is switched off
but all settings and totals are stored. In this mode, power consumption
is extremely low.
To wake up the F130-P again, press the START/key two times.
3.3.7 MENU 6 - FLOWMETER
With this setting the type of flowmeter output is selected. The settings with LP (low-pass) filter are
used to apply a build-in noise reduction. Selections "active pulse" offer a detection level of 50% of
the supply voltage.
6
FLOWMETER
6.1
SIGNAL
With this setting the type of flowmeter output is selected. The settings with
LP (low-pass) filter are used to apply a build-in noise reduction.
Selections "active pulse" offer a detection level of 50% of the supply voltage.
TYPE OF SIGNAL
EXPLANATION
RESISTANCE
FREQ. / mVpp
REMARK
NPN
NPN input
100 kΩ pull-up
max. 6 kHz.
(open collector)
NPN - LP
NPN with low pass filter
100 kΩ pull-up
max. 1.2 kHz.
(open collector)
less sensitive
REED
Reed-switch input
1 MΩ pull-up
max. 1.2 kHz.
REED - LP
Reed-with low pass filter
1 MΩ pull-up
max. 120 Hz.
Less sensitive
PNP
PNP input
100 kΩ pull-down
max. 6 kHz.
PNP - LP
PNP with low pass filter
100 kΩ pull-down
max 1.2 kHz.
Less sensitive
NAMUR
NAMUR input
820 Ω pull-down
max. 4 kHz.
External power
required
COIL-HI
High sensitive coil input
-
min. 20 mVpp
Sensitive for
interference!
COIL-HI (option ZF)
min. 10 mVpp
COIL-HI (option ZG)
min. 5 mVpp
COIL LO
Low sensitive coil input
-
min. 80 mVpp
Normal sensitivity
8-1 DC
Active pulse input
detection level 8.2 V DC
3.9 kΩ
max. 10 kHz.
External power
required
12 DC
Active pulse input
detection level 12 V DC
4 kΩ
max. 10 kHz.
External power
required
24 DC
Active pulse input
detection level 24 V DC
3 kΩ
max. 10 kHz.
External power
required
3.3.8 MENU 7 - RELAY OUTPUT
Two control outputs are available to control relays or valves. Relay 2 (R2) can also be used as pulse
output according the batch total (actual) or accumulated total.
7
RELAYS
7.1
RELAYS
This submenu is used to set the function of related output.
1-Step: The F132-P is used for one-stage batch control while R2 is
used as a scaled pulse output.
2-Step: The F132-P is used for two-stage batch control.
7.2
PRECLOSE
When Setup 7.1 is set to 2-Step, R2 will be used to control a second
valve for the batch process. Then, the switch-off-moment for R2 has to
be set. The switch moment is based on the remaining quantity before
the end of batch.
If preclose is set to zero, R2 will switch simultaneously with R1.
The settings: width, decimals, amount and pulse are only valid when R2
is used as a scaled pulse output. A scaled pulse output is used to
indicate that the batch or accumulated total has increased with the
value as set in Setup 7.5.

Page 17
FW_F130-P_M_v2201-01_EN.docx
7.3
WIDTH
When Setup 7.1 is set to 1-Step, R2 is used as a scaled pulse output.
The pulse width determines the time that the output will be active; in

output.
The pulse signal always has a 50% duty cycle, hence the minimum
time between the pulses is equal to the pulse width setting. If the
frequency should go out of range when the flow rate increases for
example 

It might be that pulses will be missed due to a buffer-overflow, so it is
advised to program this setting within its range!
7.4
DECIMALS
This setting is used to set the amount of digits behind the decimal point
for the amount.
7.5
AMOUNT
With Setup 7.1 set at 1-Step, a pulse will be generated on R2 every
time a certain quantity is added to the total chosen with Setup 7.6.
Enter this quantity here while taking the decimals set at Setup 7.4 into
account.
7.6
PULSE
The pulse generation is related to the batch total or the accumulated
total.

new batch is started.
3.3.9 MENU 8 - COMMUNICATION (OPTION)
The F130-P can optionally be equipped with a communication interface using the Modbus protocol
(Type CB/CH/CI/CT). Please consult Appendix C for a more detailed explanation of the protocol,
data types and available registers.
8
COMMUNICATION
8.1
SPEED
This setting is used to set the baud rate and should match the speed
used on the communications bus.
The following communication speeds can be selected:
1200 2400 4800 9600
8.2
ADDRESS
This setting is used to configure the bus address of your device on the
communications bus. This address can vary from 001-255.
8.3
MODE
This setting is used to configure the Modbus communication mode of
your device on the communications bus.
The following modes can be selected: ASCII RTU OFF
3.3.10 MENU 9 - OTHERS
9
OTHERS
9.1
MODEL
For support and maintenance it is important to have information about
the characteristics of the F130-P. Your supplier will ask for this
information in the case of a serious breakdown or to assess the
suitability of your model for upgrade considerations.
9.2
SOFTWARE VERSION
9.3
SERIAL NO.
9.4
PASSWORD
All SETUP values can be password protected.
This protection is disabled with value 0000 (zero).
A 4 digit password can be programmed, for example 1234.
9.5
TAG-NR
For identification of the unit and communication purposes, a unique
tag number of maximum 7 digits can be entered.

Page 18
FW_F130-P_M_v2201-01_EN.docx
4 INSTALLATION
4.1 GENERAL DIRECTIONS
•Mounting, electrical installation, start-up and maintenance of this device may only be
carried out by trained persons authorized by the operator of the facility. Persons must
read and understand this manual before carrying out its instructions.
•The F130-P may only be operated by persons who are authorized and trained by the
operator of the facility. All instructions in this manual are to be observed.
•Ensure that the measuring system is correctly wired up according to the wiring diagrams.
Protection against accidental contact is no longer assured when the enclosure cover is
removed or the panel cabinet has been opened (danger from electrical shock). The
enclosure may only be opened by trained personnel.
•Take careful notice of the "Safety rules, instructions and precautionary measures" at the
front of this manual.
The F1-Series can be supplied as suitable for Safe Area or Hazardous Area. This is indicated in the
model code (shown on the product label) by the Type X* designator, with following options:
•Type XX: Suitable for safe area applications only (e.g. F130-P-XX)
Follow the mechanical and electrical installation instructions shown in chapter 4.
•Type XF: Suitable for explosion proof / flame proof applications (e.g. F130-P-XF)
Follow the electrical installation instructions as shown in chapter 4 and
the mechanical installation instructions of the enclosure that are supplied separately.
•Type XI: Suitable for intrinsically safe applications (e.g. F130-P-XI)
Follow the general mechanical and electrical installation instructions of chapter 4
and the specific installation instructions of chapter 5
4.2 INSTALLATION / SURROUNDING CONDITIONS
Take the relevant IP classification of the
enclosure into account (see identification plate).
Even an enclosure rated for IP67 / TYPE 4(X)
should NEVER be exposed to strongly varying
(weather) conditions.
When used in very cold surroundings or varying
climatic conditions, inside the instrument case,
take the necessary precautions against moisture.
Mount the F-Series onto a solid structure to avoid
vibrations.
For use in Safe and Hazardous Areas (or Locations), the following conditions apply:
Relative humidity:
< 90% RH
Outdoor use:
suitable for outdoor use
IP and TYPE rating:
IP65 (panel mount), IP67 (field mount) and Type 4X
Supply voltage fluctuation:
As indicated by the supply range (e.g. 10V to 30V),
otherwise +/- 10% unless stated otherwise
Means of protection:
Intrinsically safe:
IS
Ordinary locations:
Class I (PE connected metal enclosure)
Class II (non-metallic enclosure)
Over-voltage category:
II (when supplied from mains)
Pollution degree:
2 (internal environment), 3 (external environment)
Ambient:
Intrinsically safe:
-40 °C to +70 °C, -40 °F to +158 °F
(limited to +50 °C, 122 °F for EPL Da)
Ordinary locations:
-40 °C to +80 °C, -40 °F to +176 °F
Altitude:
up to 2000 m

Page 19
FW_F130-P_M_v2201-01_EN.docx
4.3 HANDLING THE F-SERIES ENCLOSURE
4.3.1 IDENTIFICATION
The F1-Series can be supplied as suitable for Safe Area or Hazardous Area.
Suitability for Intrinsic Safety is indicated in the model code by Type XI (e.g. F130-P-XI).
For Intrinsically Safe applications: Installation and identification labels are shown in chapter 5.
Identification label
To identify your F1-Series device, all field mount enclosures have a weatherproof identification label
placed on the outside of the unit.
Fig. 9: Identification Example of F1-Series identification label (safe area)
Installation label
A second label is located on the inside and shows additional installation data. For panel mount
enclosures, the outside label is not available, so the inside label also serves as identification label.
After installation, the inside label is only visible from the rear side of the panel.
Fig. 10: Identification Example of F1-Series installation label (safe area)

Page 20
FW_F130-P_M_v2201-01_EN.docx
Terminal label
Also on the inside, a terminal label is placed to indicate the location of the terminals and settings for
the sensor supply configuration switches.
Fig. 11: Identification Example of F1-Series terminal label (safe area)
Serial number and year of production
The serial number can be reviewed on the identification label or in
SETUP-menu Others. The production date is either shown separately on
the label or indicated by the first 4 digits of the serial number
representing year and week number (YYWW).
4.3.2 OPENING / REMOVING THE COVER
To open the F-Series enclosure, the front cover needs to be removed. Please follow this procedure:
1. If necessary, clean the enclosure with an anti-static
cloth made damp with a mild soap solution. Wait for
the enclosure to dry before opening.
2. While loosening the screws, hold on to the front
cover to prevent it from falling down.
3. Unscrew all 4 screws from the front of the enclosure
and (if present) mind that the serrated washers are
kept with the screws.
4. Carefully take the front cover away from the rear
cover, minding that the wiring stays intact.
5. Depending on the work to be done, all terminal
connectors can be removed from their mating parts
and the front cover is now completely separate.
4.3.3 CLOSING / REPLACING THE COVER
To replace the cover on the F-Series enclosure, follow this procedure:
1. Re-insert all terminals to their original position.
2. Carefully position the front cover onto the back cover, making sure
that the gasket falls nicely into the gutter of the back cover.
3. Replace all 4 screws into the front cover and mind that the serrated
washers are replaced (metal enclosure only).
4. Fasten all 4 screws in an alternating way so that the front cover is
placed evenly across the edge of the back cover.
Tighten the 4 screws with the torque value for the type of enclosure
as specified in following table:
Plastic enclosure: 1 Nm per screw
Aluminum enclosure: 1 Nm per screw
Aluminum w. extended back enclosure: 1 Nm per screw
Stainless steel enclosure: 2 Nm per screw
5. The F-Series in now ready to be returned to service.