Flycam FLCM-FLN-MSTR-PLA User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Flowline Master for Camera & Gimbals with Placid
Stabilizing Arm (FLCM-FLN-MSTR-PLA)
Assembly Manua l
Camera Hook
Support Bar
Side Support
Adjustment
Release
Lever
Balance Adjustment
Knob
Bag Packing
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Safety Shock Cord
Tensioner Spring
Accessory Bag

2
 Remove placid from foam packing. The
placid arm has a cord aached to it. Join
secon 1 of the support bar to secon 2
with a simple push-t technique, as shown
in the image.
 Insert the placid arm into the support bar
through the cord and secure it correctly
with the help of a knob.
Flowline Master with Placid Setup
 To x the placid arm at its appropriate
posion, aach one side of the safety shock
cord to a knob on the placid arm. Then, drag
the other side of the elasc cord across the
owline support arm, and aach it to the
knob on the other side of the placid arm.
 Adjust & ghten the buckles provided at the
chest and the waist.
 Loosen the knob of the camera hook and
aach the camera to it. Tighten the knob to
ensure a slip-free connecon.
 When assembled, the owline master will
look the same as shown in the image.

3
Detach the Placid from the Flowline Master
 Get the spring o the camera hook with the
help of an Allen key.
 Through the balance adjustment Knob, you
can adjust the balance an-clockwise
according to the weight of your setup.
CAUTION: Do not release the lever without
removing the setup. It may result in severe
damage to the camera.
 Pull the camera hook cup through the cord
and remove the remaining cord from the
cup.
 To remove the placid arm from its posion,
unscrew one side of the safety elasc cord
from the plaid arm's knob. Then, pull the
other side of the elasc cord out from the
owline support arm.
For Safety Belt
 Aach one end of the safety belt with the
support jacket and make a knot with the
rest of the belt, as shown in the image. You
can aach this belt in many areas according
to your requirement.
 Aach the other end to your camera for
more safety & protecon.

4
 Using an allen key, pull the mounng
bracket of the placid arm out of the owline
support arm and remove the cord from the
bracket. Make sure it comes out precisely
through the hole in the placid arm.
 Secure the cord properly with the cord lock
and insert the cord bundle into the cup.
 Insert the cord into the cup. Then, aach
the cord lock to the cord.
 Aach the camera hook to the owline
support bar, as shown in the picture.
Cord Assembly into Flowline Master
Note: The camera hook will be below the
owline support bar while using the camera,
and it will be up when aaching the placid, as
shown in the image.

5
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of
me, we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor
does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to
inspecon and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
YOUR FLYCAM FLOWLINE MASTER FOR CAMERA & GIMBALS WITH PLACID
ALL DRESSED UP AND READY TO GO