for Living Essex 088-1872-0 User manual

Essex Gazebo（Grey）
Model No. 088-1872-0
Toll-free: 1-844-786-5691
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions

3
Imported for Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Made in China
Table of ContentsImportant Safety Instructions
Table of contents 3
Important safety instructions 3
Package contents 4
Assembly 6
Cleaning and maintenance 20
Specifications 20
Warranty 21
Warning! To reduce the risk of serious injury, read the following safety instructions before
assembling and using the gazebo.
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.
 This product is intended for domestic outdoor use i.e. decorative and sunshade purposes only.
 Always place and assemble the gazebo on flat horizontal ground.
 Consult with your local governing authority / local municipal codes regarding installation of temporary
structures before assembly.
 Ensure there is enough clearance around the product. Before assembling the gazebo, make sure to leave
a distance of not less than 6' (1.8 m) from any structures or obstructions, such as fences, garages, houses,
overhanging branches, laundry lines, or electrical wires.

Anchor the gazebo to the ground with stakes for added safety. Stakes are provided to secure the gazebo to the
ground. If you wish to secure the gazebo to a concrete and wood surfaces, use anchors suited for these surfaces
(anchors not included). Do not assemble the gazebo on sandy, muddy or loose soil, as stakes are not strong enough
If more than one gazebo is set up, keep a minimum distance of 10' (3 m) between the gazebos.
 Any assembly or maintenance of the gazebo must be carried out by adults only.
 Make sure there is sufficient manpower when assembling or moving the gazebo.
 Some parts may contain sharp edges. Wear protective gloves if necessary.
 Check all nuts and bolts periodically for tightness. If required, tighten them.
 Repairing and replacing parts should be done by a qualified technician.
 Always disassemble the gazebo before experiencing heavy wind conditions, as it is not designed to withstand
harsh weather, including high wind, rain, and snow. In these conditions, it might tip over and could cause injury
to bystanders.
 Do not hang any weights on the roof frame.
 Do not climb onto the roof of the gazebo. Doing so may cause the gazebo to fall down, possibly resulting in
serious injury.
 During snow days, remove the snow at the top when the snow is thicker than 4" (10 cm).
 After a period of time, usually in 2–3 months, tighten all the bolts.
 After a few years, if the paint peels off, use paint of similar color. It is recommended to use outdoor paint.
 If the gazebo will not be used for a long period of time (e.g. during winter time), disassemble and store it in a
clean, dry environment.
 Retain the original packaging to store the gazebo.
Caution! Always keep children under close supervision while they are near this product. Keep pets away while
setting up the gazebo.
Caution! Check municipal by-laws prior to setting up the gazebo.
to anchor in these types of soil.

4 5
Model No. 088-1872-0
Package Contents
Package Contents
Long side left roof panel 3 - 2
Long side right roof panel 3 - 2
Short side roof panel 1 - 2
Short side left roof panel 2 - 2
Short side right roof panel 2 - 2
Short side left roof panel 3 - 2
G3
H3
I3
J3
K3
L3
Big top frame - 2
Upper beam connector - 4
Big top bar - 2
Lower beam connector - 4
Small top support beam - 4
Short beam - 4
Small top connector - 1
Long beam - 4
Hook - 1
Arc support - 8
Top roof small panel - 2
Long pipe 1 - 2
Long pipe 2 - 2
Short pipe 1 - 2
Short pipe 2 - 2
Top roof long panel - 2
Small top cover - 4
Small top roof cover - 1
Post - 4
Top slanting bar - 4
Top beam - 4
Long side left roof panel 1 - 2
Beam connector - 8
Base cover - 4
Base - 4
A1
G2
B1
H2
C1
I2
D1
J2
E1
K2
F1
G1
H1
I1
A4
A3
B3
C3
C2
D2
E2
M2a
L2a
L2b
M2b
Short side right roof panel 3 - 2
Big roof panel cover (corner) - 4
M3
N3
Big roof panel cover (middle) - 4
O3
Big roof top beam (long side) (1) - 2
Big roof top beam (long side) (2) - 2
Big roof top beam (long side) (3) - 2
Big roof top beam (long side) (4) - 2
Big roof top beam (long side) (5) - 2
Big roof top beam (long side) (6) - 2
X1
X2
X3
X4
X5
X6
Slanting bar connector - 4
F2
Long side right roof panel 2 - 2
F3
Long side left roof panel 2 - 2
E3
Big roof top beam (short side) (2) - 2
W2
4
Big roof top beam (short side) (4) - 2
W4
4
Big roof top beam (short side) (3) - 2
W3
4
Big roof top beam (short side) (5) - 2
4
Big roof top beam (short side) (6) - 2
W5
W6
Long side right roof panel 1 - 2
D3
Big roof top beam (short side) (1) - 2
W1

Caution!
tProper placement of the gazebo is essential. Do not place the gazebo underneath
electrical lines.
tKeep children under close supervision while they are near this product. This product
contains small parts which can be swallowed by children.
tKeep fingers away from places where they can be pinched or trapped.
tDo not attempt to assemble the gazebo if any part is missing.
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
1-844-786-5691
If you have questions regarding your product, require warranty assistance,
or have damaged or missing parts, please call our customer service toll-free helpline.
Contact us for assistance; we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning the assembly of the
product, make sure all parts are available. Compare parts with package contents list. If any part is missing, or if you
have any questions, contact the service center at 1-844-786-5691 (toll-free).
Take all parts from the box and position them on a clean floor. Remove all packing materials and place them back
into the box. Do not dispose of the packing materials until assembly is complete. Read each step carefully before
beginning any assembly and make sure you understand each step.
Needed for assembly:
Hammer Screwdriver Ladders (6' / 2 m tall) 5 people
Assembly
6 7
Model No. 088-1872-0
Screw (1/4" - 20 x 0.6) - 140 + 7 spare
Flat washer (1/4") - 330 + 17 spare
Screw (1/4" - 20 x 2.125) - 22 + 2 spare
Nut (1/4") - 36 + 3 spare
Screw (1/4" - 20 x 1.4) - 24 + 2 spare
Bolt (1/4" - 20 x 0.6) - 80 + 4 spare
Bolt (1/4" - 20 x 2.6) - 16 + 2 spare
Bolt (1/4" - 20 x 1.75) - 32 + 2 spare
Stake (5/16 x 10.24") - 16
Wrench (1/4") - 2
AA
BB
CC
DD
EE
FF
GG
HH
II
Z
Package Contents

8 9
Model No. 088-1872-0
Note: When using screws and nuts to assemble the product, always use a flat washer between the frames
and the screw and/or nut. This will protect the parts from wear and tear.
Step 1
Requires A1, B1, AA, BB
Step 2
Requires C1, A1, AA, BB
Attach the big top frame (A1) to the big top bar (B1) using screw (AA) and flat washer (BB).
AA
BB A1
B1
C1
A1
BB
Assembly
Attach one end of the small top support beam (C1) to the connector of the big top frame (A1) using screw (AA)
and flat washer (BB).
BB
AA
BB
AA
Step 3
Requires C1, D1, BB, CC, DD
D1
DD
CC
C1
Step 4
Requires D1, E1
D1
E1
Attach the other end of the small top support beam (C1) to the small top connector (D1) using nut (DD), flat
washer (BB) and screw (CC).
Insert and screw the hook (E1) tightly into the corresponding hole on the small top connector (D1).
BB CC DD
Assembly

10 11
Model No. 088-1872-0
Assembly
Step 5
Requires A4, C2, BB, FF
Attach the beam connector (C2) to the post (A4) using bolt (FF) and washer (BB).
C2
A4
FF
BB FF
Step 6
Requires A4, F2, BB, FF
F2
FF
A4
BB FF
Attach the slanting bar connector (F2) to the post (A4) using bolt (FF) and washer (BB).
Assembly
Step 7
Requires A4, D2, E2, AA, BB
A4
D2
A4
E2
AA
(7a) Insert the post (A4) into base cover (D2). (7b) Attach the base (E2) to the post (A4) using
screw (AA) and washer (BB).
AA BB
Step 8
Requires G2, H2, I2, J2, BB, DD, GG
I2
H2
I2
G2
J2
H2
J2
G2
BB BBDD DD
GG GG
(8a) Attach beam connector (G2), (H2), short beam (I2)
using bolt (GG), washer (BB), and nut (DD).
(8b) Attach beam connector (G2), (H2), long beam (J2)
using bolt (GG), washer (BB), and nut (DD).
BB
BB
GG GG
DD DD

12 13
Model No. 088-1872-0
Step 11
Assembly
Step 12
Requires A3, B3, F2, G2, BB, CC, DD
A3
CC
F2
G2
CC
B3
BB CC DD
(11a) Attach one end of the top slanting bar (A3)
to the slanting bar connector (F2) using
screw (CC), washer (BB) and nut (DD).
(11b) Attach one end of the top beam (B3) to the
upper beam connector (G2) using screw (CC),
washer (BB) and nut (DD).
BB CC DD
Step 9
Requires C2, I2 J2, BB, FF
C2
FF
Connect the other ends of long beam (I2) and short beam (J2) to the beam connector (C2) using screw (FF) and
washer (BB).
BB FF
Step 10
Requires A4, K2, BB, HH
K2 HH
A4
Attach the arc support (K2) to the post (A4) and short/long beams. Secure them using bolt (HH) and washer (BB).
BB HH
Assembly
Requires A1, A3, B1, B3, BB, FF
FF
A1
B3
B1
A3
Attach top slanting bar (A3) and big top frame (A1), top beam (B3) and big top frame (A1) / big top bar (B1) using
bolt (FF) and washer (BB).
BB FF
I2(J2)

14 15
Model No. 088-1872-0
Assembly
Step 15
Requires W1, W2, W3, W4, W5, W6, AA, BB
Attach the big roof top beams (short side) (W1, W2, W3, W4, W5, W6) to the top slanting bar and the top beam
using screw (AA) and washer (BB).
BB
AA
AA
W2
W1
W3
W4
W6
W5
Step 16
Requires X1, X2, X3, X4, X5, X6, AA, BB
Attach the big roof top beams (long side) (X1, X2, X3, X4, X5, X6) to the top slanting bar and the top beam using
screw (AA) and washer (BB).
AA
X2
X1
X3 X4
X6
X5
BB
AA
Assembly
Step 13
Requires F1, G1, AA, BB
F1
G1 AA
AA BB
Place the top roof small panel (F1) and the top roof long panel (G1) onto the small top support beam and attach
using screw (AA) and washer (BB).
Step 14
Requires C1, D1, H1, I1, BB, EE
H1
H1
C1
EE
I1 CC
D1
BB EE
(14a) Place the small top covers (H1) onto the
small top support beam (C1) and attach
using two screws (EE) and washers (BB).
(14b) Place the small top roof cover (I1) onto the
small top connector (D1) and attach using
two screws (CC) and washers (BB).
BB CC

16 17
Model No. 088-1872-0
Assembly
Repeat the above procedure for connecting short pipes (M2a, M2b) to the top slanting bar.
Step 20
Requires M2a, M2b
M2b
M2a
Step 19
Requires A3, L2a, L2b, AA, BB
Attach the other end of the long pipes (L2a, L2b) to the top slanting bar (A3) using screw (AA) and washer (BB).
L2b
A3
L2a
BB
AA
Assembly
Step 17
Requires B3, L2a, L2b, AA, BB
Attach one end of the long pipes (L2a, L2b) to the top beam (B3) using screw (AA) and washer (BB).
L2b
B3
L2a
BB
AA
Repeat the same procedure for connecting short pipes (M2a, M2b) to the top beam.
Step 18
Requires M2a, M2b
M2a
M2b

18 19
Model No. 088-1872-0
Step 23
Requires C1, N 3
N3
C1
Insert the big roof panel cover (corner) (N3) into the hole of the small top support beam (C1).
Assembly
Step 24
Requires A3,B3, N3, O3, BB, EE
EE
N3
EE
O3
B3
BB EE
(24a) Attach the big roof panel cover (corner) (N3) to
the top slanting bar (A3) using screw (EE) and
washer (BB).
BB EE
(24b) Attach the big roof panel cover (middle) (O3) to
the top beam (B3) using screw (EE) and
washer (BB).
Assembly
Step 21
Requires C3, D3, E3, F3, G3, H3, AA, BB
Place the long side roof panels (C3, D3, E3, F3, G3, H3) onto the big top frame from upper end to lower end and
attach using two screws (AA) and two washers (BB) on each panel.
AA
D3
H3
G3
E3
C3
F3
BB
AA
Step 22
Requires I3, J3, K3, L3, M3, AA, BB
I3
J3 K3
L3 M3
AA
BB
AA
Place the short side roof panels (I3, J3, K3, L3, M3) onto the big top frame from upper end to lower end and
attach using two screws (AA) and two washers (BB) on each panel.

Cleaning and MaintenanceSpecications
20 21
Model No. 088-1872-0
Assembly
Step 25
Requires D2, E2, II
E2
II
D2
(25a) Move and hold base cover (D2) upward so
the base (E2) can be anchored to the ground
using the stakes (II). Then put down the
base cover. Repeat this step until all four
posts are anchored.
(25b) The gazebo is ready for use.
II
tDo not use bleach, acid, or other abrasive cleaners on the roof panels or beams.
tSteel components of garden accessories and furniture are coated with rust-inhibiting paint. However, due
to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is
a natural process. To minimize this condition, it is recommended that care be taken when assembling and
handling the product, in order to prevent the paint from being scratched. Surface rust can be removed easily
by applying a little common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to
correct it, the oxidation may start dripping onto the assembly surface, which may cause rough stains that
could be difficult to remove.
Caution!
tCheck all screws and nuts periodically for tightness. Tighten them if required.
tDisassemble the gazebo in the reverse order of the assembly steps. Always disassemble
the gazebo completely. A partially disassembled gazebo is not stable enough to resist
wind and bad weather, and therefore can be damaged and/or cause damage.
Dimensions (L x W x H) 144 x 121 x 121"
366 x 308 x 307 cm
Product weight 346 lb
157 kg

22 Model No. 088-1872-0
This For Living™product carries a three (3) year limited warranty against defects in workmanship and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period,
when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse.
Warranty