Force JX-1300 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Model
SPARTAN
Retain This
Manual for
Reference
2017-2-13
OWNER'S
MANUAL
OWNER’S MANUAL JX-1300
3 Station Home Gym with 145LBS pin loaded weight stack

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 3
ASSEMBLY INSTRUCTIONS.........................................................................……….. 6
CARE AND MAINTANENCE........................................................22
PARTS LIST………………………………………………………………………………….. 23
BEFORE YOU BEGIN.
Thank you for selecting the JX-1300 Three Station Home Gym. For
your safety and benefit, read this manual carefully before using the
machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find
there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory.
1

PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. WE
ASSUME NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
IMPORTANT SAFETY NOTICE

HARDWARE
3

4

5

Assembly step
It is strongly recommend that two or more person assemble this three station home
gym.
Tool required assembly the machine: two adjustable wrenches, and one Philips
screw driver
Carefully unpack each component ,checking against the part list that you have all
the necessary parts to complete the assembly.
STEP 1
A)Insert the 2 pcs Guide Rod（13#）into the two holes on the rear stabilizer
（2#）,And secure them with 2pc M10×25 Allen bolt（90#）and 2pcs φ10 Washer
(100#), And then slide 2 pcs rubber bumper(57#) onto the Guide Rods from the top
to the bottom.
Do not fully tighten the bolts and nuts until getting instruction.
B.) Attach the Main base frame (1#) to the Rear Stabilizer(2#) , Secure them with 2 pcs
M10×70 Carriage Bolt （89# ）, one pc U- Shaped Bracket （38# ）,2pcs φ10
Washer(100#) and 2pcs M10 Aircraft nut (97#) .
C.) Attach the Front vertical frame (3#) onto the Main base frame (1#), And Secure
them with 2pc M10X70 Carriage Bolt(89#), 1 pc bracket(31#),2 pcs φ10
Washer(100#) and 2 pcs Aircraft nut (97#).
6

SETP 2
A)Slide 14 pcs Weight Plate（45#）onto the Guide Rods （13#）from the top to the
bottom，Make sure all the deep grooves on the weight plates face the Front and
downwards. Align the holes and Insert the Selector Rod（12#）into the hole on the
weight plates，and then place the Selector Stem（44#）onto the Selector Rod(12#).
Select the desired number of Weight Plate with L-Shaped Pin（93#）
when doing the exercise；
B)Place the Upper Frame (4#)Onto the 2 PCS Guide Rod（13#）and align the holes,
Secure them with 2PCS M10×25 Allen Bolt（90#）、2PCS φ１０Washer(100#) .
C）Attach the Upper Frame (4#) onto the Front Vertical Frame(3#) and Secure them
with 2 pcs M10×90 Carriage Bolt（88#), one Bracket (31#),2PCSφ10 Washer
（100#）,2PCS M10 Aircraft Nut（97#）.
7

STEP 3
A) Attach the Front Press Frame(5#) to the Upper Frame(4#),Secure them with Front press
Axle(91#), Two Pcs φ10 Washers（100＃）and 2PCS M10 Aircraft Nut（97＃）. Do not
fully tighten the bolts and nuts.
Make sure the Front Press Frame (5#) can swivel freely.
B) Attach the Right Butterfly Frame (8#) to the Front press Frame(5#),and secure them with
1 pc Allen Bolt(108#),1 PC Lock Ring(59#) and 1PC M6 Aircraft Nut(95#). Insert the Foam
Roll (71#)into the Right butterfly(8#) from the bottom to the mid of the right butterfly,
attach the front press handle (10#) to the right Butterfly(8#) and then Secure them with
1PC M10*85 Allen bolt(87#).
C) Repeat the procedure B to install the left butterfly(7#).
D) Attach the Backrest pad (39#) to the Front Vertical frame(3#) and Secure them with
2PCS M8*85 Allen Bolts (111#)and 2PCS φ8 Washers(101#).
E) Attach the Pulley Bracket(16#) to the Front Vertical Frame(3#) and Secure them with one
pc M10*110 Allen Bolt(86#),2pcsφ10 Washers (100#) and one M10 Aircraft
Nut(97#).Attach the Swivel Pulley Bracket (19#) to the pulley bracket(16#) and Secure
them with M10*65 Allen Bolt(109#), two PCSφ10 Washers(100#) and M10 Aircraft
Nut(97#).Install the another Swivel bracket(19) with the same method.
8

STEP 4
A) Attach the Seat Support Frame (6#) to the Front Vertical Frame(3#) and Secure them
with two pcs M10*90 Carriage Bolt(88#), one pc Bracket(35#) two pcsφ10
Washers(100#), and two pc M10 Aircraft Nut(97#).
B) Attach the Leg Developer (9#) to the front of the Seat Support Frame(6#) and
Secure them with two pcs M10*16 Allen Bolt(105#), two pcs φ10
Washers(100#),one PC Swivel Axle(92#). Do not tighten the bolts and make sure the
Leg developer can swivel freely. Insert the Arm Curl Stand (11#) into the top
opening of the Seat Support Frame(6#) and choose different height with lock
knob(63#).
C) Place the Seat Pad (40#) onto the Seat Support Frame(6#), and Secure them with
Two pcs M8*65 Allen Bolts(112#), two pcs φ8 washers(101#) . Place the Arm Curl
Pad (41#) onto the Arm Curl Pad Support(11#) and Secure them with 2pcs M8*16
Allen Bolts(106#), Twoφ8 washers(101#).
D) Insert one pc Foam Roll Tube(33#) into the hole of Seat Support Frame (6#)halfway,
another Roll Foam Tube into the hole of Leg Developer(9#). Place the four Foam
rolls(70#) onto the Foam Roll Tube (33#) from two ends. And then insert the four
End Cap (51#) into the Foam Roll Tube(33#).
E) Attach 2pcs Foot Plate(20#) to the Main Base Frame(1#), Secure them with 2pcs
Carriage Bolts(88#),two Pcsφ10 washers(100#) and M10 Aircraft Nuts(97#)
9

STEP 5
A) Attach the Upper Cable(75#) through the bracket of Upper frame(4#), Make
sure that the ball stopper should be underneath the frame.
B) Attach one pc Pulley (60#) to the bracket and secure them with one pc
M10*45 Allen Bolt(104#), two pcsφ10 washer(100#) and one pc M10 Aircraft
Nut(97#).
C) Draw the Upper cable(75#) backwards and to the top bracket of the vertical
frame(3#) and then repeat the procedure B to install a pulley.
D) Draw the cable towards the pulley and through the centre of the front press
frame(5#) and then repeat the procedure B to install one pc pulley.
E) Draw the Upper cable(75#) backwards through the hole on the front vertical
frame(3#)and repeat the procedure B to install one pc pulley.
F) Draw the Upper cable(75#)downwards and place one pc pulley onto the cable ,
Secure the pulley to the double floating pulley bracket(17#) with one pc
M10*45 Allen Bolt(104#), two pcsφ10 washer(100#) and one pc M10 Aircraft
Nut(97#).
G) Draw the cable around the pulley upwards , place two pcs pulley to the
opening of rear of the upper frame (4#) and secure them with two pcs
M10*45Allen Bolt(104#) ,four pcs φ10 washer(100#) ,two pcs L-shape
separation blade(117#),two pcs M10 Aircraft Nut(97#).
H) Draw the cable downwards between the two Guide Rod(13#)to the Selector
Rod (12#),thread the bolt into the opening on the top of the Selector Rod to
secure the cable.
NOTE: Tighten or loosen the end bolt of the upper cable(75#)can adjust the
tension of the cable system. Please make sure the bolt screw inside of the
weight selector rod (12#) at least 5 laps.
10

11

STEP 6
A) Attach one end of the butterfly Cable (76#)to the hook on the right butterfly(8#).
Place one pc Pulley (60#) under the cable, and position the pulley into the
Swivel Pulley bracket(19#),and secure them with one pc M10*45 Allen
bolt(104#),two pcsφ10 washer(100#),one M10 Aircraft Nut(97#).
B) Draw the Butterfly Cable (76#)downwards, place one pc pulley (60#) onto the
cable and secure the pulley to the Cross double floating pulley bracket
(18#)with one pc M10*45 Allen bolt(104#),two pcs φ10 washer(100#),one M10
Aircraft Nut(97#).
Note: let the pulley assembly hanging at this stage.
C) Draw the cable upwards around the pulley. Repeat the Procedure B to install
the pulley to left side swivel pulley bracket.
D) Attach another end of the butterfly cable (76#) to the hook on the left butterfly.
12

STEP 7
A）Remove the Double Strap Buckle(74#) and ball stopper from the end of Lower
cable(77#) , so that the lower cable(77#) would go through the holes .
B)Attach the low cable(77#) to the opening of the leg developer(9#),make sure that
the ball stopper should be on the front of the leg developer. Attach one pc Pulley
(60#) into the opening and secure them with one pc M10*45 Allen bolt(104#),two
pcsφ10 washer(100#),one M10 Aircraft Nut(97#).
C)Attach the cable backwards of the machine through the second bracket and the
opening of the front vertical frame(3#),attach two pcs pulley(60#) onto the cable
and secure them with two pc M10*45 Allen bolt(104#),four pcsφ10
washer(100#),two M10 Aircraft Nut(97#).
D)Draw the cable upwards, place one pc pulley(60#) behind the cable and Secure
the pulley to the another side of Cross double floating pulley bracket(18#).
E)Draw the cable downwards, place one pc pulley onto the cable and secure the
pulley to the bracket with one pc M10*45 Allen bolt(104#),two pcs φ10
washer(100#),one M10 Aircraft Nut(97#).
F)Draw the cable upwards, and place one pc pulley behind the cable, Attach the
pulley to the double floating pulley bracket and secure them with one pc M10*45
Allen bolt(104#),two pcsφ10 washer(100#),one M10 Aircraft Nut(97#).
G)Draw the cable downwards and place one pc pulley onto the cable, and then
secure the pulley to the bracket of the front vertical frame(3#).
H)Draw the cable upwards, through the opening of the front vertical frame(3#), place
one pc pulley into the opening and secure it with one pc M10*65 Allen
bolt(109#),two pcsφ10 washer(100#),and one M10 Aircraft Nut(97#).
I)Attach the Double Strap Buckle(74#) to the end of low cable(77#), and secure them
with one pc M10*30 Allen Bolt(113#), two pcs φ10 washer(100#), and one pc M10
Aircraft Nut(97#).
13

14

STEP 8
A) Attach the left & Right Weight stack Cover(36&37) together, and Secure them
with four pcs Philips Screw (107#) and four M5 aircraft Nut(96#).
B) Place the left & Right Weight Stack Cover(36&37)onto the Rear Stabilizer(2#)
and Secure them with 6PCS M10*16 Allen Bolts(105#),6pcsφ10 washer(100#）.
15

STEP 9
A) Attach the left side Stabilizer (23#)and right side stabilizer(24#) to the Main base
Frame(1#), And secure them with two pcs M10*90 Carriage Bolt(88#),two pcs Ø 10
washers(100#) and two pcs M10 aircraft Nuts(97#).
B) Attach the lower vertical frame (26#) to the right side stabilizer stabilizer(24#), and
secure them with two pcs M10*70 Carriage Bolt (89#), one pc bracket(35#),two pcs
Ø 10 washers (100#),Two pcs Aircraft Nuts(97#).
16

Step 10
A) Attach the upper Vertical Frame (27#) to the lower vertical Frame(26#).
B) Attach the left Dip Arm( (29#),right Dip Arm(30#),upper vertical frame(27#) ,lower
vertical frame (26#) together. And Secure them with two pcs M10*70 Carriage
Bolts(89#), two Ø 10 washers(100#), and M10 Aircraft Nuts(97#).
C) Attach the two pcs vertical Handle (32#) onto the left Dip Arm( (29#) and right Dip
Arm(30#), , and Secure them with two M10*16 Allen Bolts(105#) ,two pc Ø 10
washer(100#).
17

STEP 11
A.) Attach the Boxing frame (21#),Upper Bent Frame(25#) and the upper frame (3#)
together, and Secure them with 2pcs M10*170 Allen Bolt(103#),Four pcs Ø 10
washers(100#), two pcs M10 Aircraft Nuts(97#),two pcs Bracket(35#).
B.) Attach the power tower Upper bent frame (25#)onto the Upper vertical Frame
(27#) and secure them with two pcs M10*70 Carriage Bolts(89#),one pc
bracket(35#) ,two pcs Ø 10 washer (100#),and two pcs M10 Aircraft Nut (97#).
C.) Insert the Chinning bar(28#) into the front opening of power tower upper bent
frame(25#), and secure them with one pc M10*65 allen bolt(109#), two pc Ø 10
washers(100#)and one pc M10 aircraft nut(97#)
D.) Attach the Hook Bolt (22#) to the Boxing Frame(21#), and secure them with one
pc Ø 12 washers(99#) and one pc M12 Aircraft Nut(98#). Attach the heavy bag
(79#) to the hook bolt (22#), Secure them with two pcs 6#Gourd Hook(82#), one
pc 7#Gourd Hook(81#),three pcs 7-Joint Chain, and one pc elastic rope(78#).
18

STEP 12
A) Attach the Backrest (42#) to the Upper vertical Frame(27#)and Secure them with
two pcs M8*70 Allen Bolt(102#),Two pcs Ø 8 wahsers(101#).
B) Attach the two pcs Arm Curl Pad (43#) onto the right & left Dip
Arm(29#&30#).and Secure them with four pcs M8*60 Allen Bolts(110#) and four
pcs Ø 8 wahsers(101#)
19