Forematic RIO-R User manual

- 1 -
Rio-R Installation manual doc. R12
doc. R12
iss V1.2
RIO-R installation manual
Contents
Description
Technical characteristics
Safety warnings
User instructions
Barrier arm options
Dimensions & layout
Installation
Controller description
Functions inputs & outputs
Accessory description
Wiring
Double leaf
gate control
panel
Specifications
Supply 230Vac 50/60Hz @ 5A
Motors 2x 100W ACIM’s
Aux supply 24Vdc @ 1A
Housing ABS IP44, 1.8kg
Dimensions 227 x 277 x 108mm
Receiver 433MHz rolling code
60 rolling code remote capacity
Auto-close 10s to 7mins
Single or double leaf
Soft stop, optional soft start
Interleaf delay 0 –9s
4 force settings
Pressure sensitive reversal
Auto run time setting
Transformer Display Accessory header
connector
+ - P
Main Code Buttons
Fuse
230Vac supply motor wiring control wiring lock wiring
Motor 1 1-2-3 - 1 neutral, 2 open live, 3 close live
Motor 2 4-5-6 - 4 neutral, 5 open live, 6 close live
AC lamp 7-8 - 7 neutral, 8 lamp live during motion
Open button 9-10 - 9 input, 10 com (-ve)
Pedestrian 11-12 - 11 input, 12 com (-ve)
Safety 2 13-15 - 11 input, 12 com (-ve)
Safety 1 14-15 - 11 input, 12 com (-ve)
Stop button 16-17 - 16 input, 17 com (-ve)
DC lamp 18-20 - 18 (+24v), 20 switch to gnd
DC lock 19-21 - 19 (+24v), 21 switch to gnd
1.0 Description
RIO-R panel is for AC induction motors with limit switches.
For single or double leaf gates / doors. Programming is
with navigation buttons and an LCD display.
1.1 Inputs & outputs
RIO-R supports two command inputs and two safety inputs.
Inputs have +5V pull ups, switching to ground. Command
inputs are active low. Safety inputs are N/C normally low.
Solid state switching outputs are provided for an electric
lock that operates for 1sec on opening. A solid state 24Vdc
flashing light output switches at 1Hz. An accessory header
is provided for powered external trigger devices such as a
keypad, loop detector, exit device, or access control device.
1.2 Input functions
SBS input Open –stop-close-stop function. When stopped
during open the gate re-closes after auto-close delay. When
stopped during closing, gate waits for next command.
Ped input Same function as SBS input, but on one gate.
Safety 1 Re-opens the gate during closure. Assuming the
danger is removed, the gate re-closes after normal delay.
No action during opening. Delays close if active while open.
Safety 2 If activated during opening, the gate stops dead.
Stays still until next command. No response while closing.
Stop During opening, stops, then re-closes after
normal auto-close delay. Stops during closing.
Wiring assumes motors include capacitors & limit switches
DC lamp does not need a flasher
M1
M2
WUVWXYWLaDCPCF2F1CECAALdK
Display
In normal running, the left digit shows the
state of inputs. Black is active. You should
have three black horizontal bars.
F1 = IR1
E = Stop
F2 = IR2
D = Door
P = Ped
Right digit segments rotate anti-clockwise
During normal running. Both digits show
alpha numeric digits during programming.

- 2 -
Rio-R Installation manual doc. R12
Exit
Loop
Foto 2
Edge 1
Foto 1
Wiring examples
Scheme shows two safety photo
beams protecting both sides of
a gate. A loop detector inside
is wired to open the gate.
One safety edge is on
the tip of one gate.
Forematic QPR12-RIOR
9 Vanalloys Estate
Stoke Row
Henley RG9 5QW www.forematic.com
Programming
Press Pto start programming. Parameter will show first.
Either programme in the given order, or keep pressing P
until the right parameter shows. Use +& -to set.
A- Auto-close delay. Disabled on A0. Presets A1 to A9.
B- Select number of motors.
C- Enable soft stop function –Slows for last 2 secs of run
D- Interleaf delay –d0 is no delay, up to d9 gives 9secs
F- Force setting, from F1 (default) to F4 (no PSR).
H- Dynamic setting. Manually Close the gates. Press +to
start. The H flashes while opening. When close limit is
found, press Pto save setting. Use remote to re-close.
Safety warnings
Automatic gates can be hazardous. It is the operators responsibility
of an automatic gate to be aware of, and provide adequate warning
of hazards. All users should be given a hazard awareness briefing and user
training for the automatic gate.
This manual is written for automation engineers aware of the construction and
accident prevention rules in force. Only qualified persons may do installation or
maintenance work on this installation. Keep the gate in good working order with
regular checks on the safety devices fitted.
Operators should ensure people are clear of the gate during operation. Children
must not be allowed to play on or near the gate, or be allowed to operate the
gate. We recommended signs both sides of the gate to warning of risk of injury
to pedestrians. Do not permit public access to the gate area.
Programming remotes
To start programming, the icon must be displayed.
Adding - Press Code button until shows.
Now press the new remote within 2 secs. Use
the button that you wish to open the gate. The
display will show the location number. If it has
already been saved, it will show the same
number. If ‘60’ shows the memory is full.
Deleting - Press and hold the Code for 10 secs. Double
F’s start flashing, then change to one Fflashing
then the display reverts to the standby icon. All
remotes in the memory are now deleted.
NO C 0v 24v
Loop detector
Loop
Rx
0v
24V
C
N/C
Tx
24V
0V
Foto 2
Rx
0v
24V
C
N/C
Tx
24V
0V
Foto 1
Edge 1 to re-open
Replace
edge with a link
if edge is not required
Ped
button
Open
button
Edge 2 to stop in
either direction Replace
edge with a link
if edge is not required
DCPCF2F1CECAA