Forest LINPL12090S User manual

REMINDER
Always pre-drill before
screwing.
IMPORTANT
Assembly requires 2+
adults.
Tape Measure Drill & 2-3mm
Drill Bits
Pozidrive
Screwdriver
50MM
SCREWS 50MM SCREWS
Forest Garden, Oak Drive, Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
EU Authorised Representative: Authorised Representative Service, 77 Camden Street Lower Dublin, D02 XE80, Ireland
Missing something or need more information?
Call our aftersales team on
0333 321 3142
Visit our website for spare instructions and
more information
www.forestgarden.co.uk
LINEAR PLANTER WITH STORAGE
INSTRUCTIONS
ISSUE: 0122
We recommend using the following
tools (not supplied):
FIXING PACK CONTAINS:
FIXING PACK CODE: LINPL12090SFP
PLEASE KEEP PLASTIC BAGS AND SMALL PARTS
AWAY FROM CHILDREN
3 x 15mm Screws
QTY: 8
Position and secure the Back Panel to the Base and
End Panel. Ensure the Back Panel is ush to the End
Panel and screw into the oor bearers beneath.
Position and secure the End Panel to the Base. Ensure
the End Panel is ush to the edge of the Base.
1
CHECK AND TIGHTEN ALL THE FIXINGS APPLIED TO THIS PRODUCT ON A
REGULAR BASIS.
Butt Hinges
QTY: 2
Magnet Set
QTY: 2
END PANEL
BASE
2BACK PANEL
4 x 50mm Screws
QTY: 36
4 x 40mm Screws
QTY: 12
3.5 x 25mm Screws
QTY: 12
Making British gardens great

3mm
50mm
50MM
SCREWS
15MM
SCREWS
25MM
SCREWS
25MM
SCREWS
15MM
SCREWS
25MM
SCREWS
3 4
6
Position and secure the hinges to the Door. Use the
measurement provided as a guide. Ensure the hinge is
ush to the edge of the top slat as shown above.
Positon and secure the Door to the Front Panel. Test opening and closing the Door before adding all screws to the
hinges. Ensure the hinge is ush to the slat on the Front Panel and there is a slight gap for the hinge pin. Allow 3mm
tolerance each side when positioning the Door.
5
Position and secure the magnet receiver to the
bottom slat on the Door. Position and secure the other
receiver on the other side.
Position and secure the End Panel to the Base and
Back Panel. Ensure the End Panel is butt up to the Back
Panel and screw into the oor bearer beneath.
FRONT PANEL
DOOR
Position and secure the magnet to the batten on the
Front Panel, just above the opening. Close the Door,
line the magnet up to the reciever and mark the position
before securing.
CLOSED HINGE

50MM
SCREWS 50MM SCREWS
40MM
SCREWS
Position and secure the Front Panel to the End Panels
and Base. Then secure the Shelf to the Front Panel.
Lay out and position the Jute Liner material inside
your planter. Overlap over the top edge and use the
Surrounds to hold in place.
Position and secure the surrounds to the panels.
Ensure the Jute Liner is held in position when screwing
the surrounds in place and the surrounds are ush
around the edge.
Position and secure the Shelf just before attaching the
Front Panel. Ensure to screw through the bearer into
the batten beneath.
HEALTH & SAFETY
We strongly recommend that PPE (Personal Protective Equipment) is used throughout your build to ensure you are
protected from any potential health and safety risks. Do not exempt yourself from wearing PPE.
7 8
SHELF
9
JUTE LINER
END SURROUND
SIDE SURROUND

TREATED TIMBER CONTAINING A BIOCIDAL PRODUCT
CONTROL OF WOOD DESTROYING ORGANISMS
Active Ingredients - Propiconazole, Tebuconazole, IPBC, Permethrine, Benzyl-C12-16-Alkyldimethyl Chlorides. (Dip Treated)
Basic Copper Carbonate, DDA Carbonate, DDA Chloride. (Pressure Treated)
Wear gloves when handling. Avoid inhalation of sawdust. Do not use in contact with drinking water or food. Do not use for animal
bedding or in sh ponds. Dispose of treated wood responsibly.
Use the labelled components to help identify the part code and description.
CHECK YOU HAVE ALL YOUR PARTS PRIOR TO ASSEMBLY.
(The parts do not have codes on them. They are listed below should you need to order one.)
Timber is a natural material of which will shrink and swell as a result of varying moisture content.
Assembly of damaged parts may be deemed to be acceptance and this may affect the remedies you are entitled to. If the product is not constructed
in accordance with the instructions, or is altered in anyway (e.g. painted), the manufacturer cannot be held liable for any resulting damage.
The components provided may be heavy. Please lift with caution and with a minimum of 2 people.
Label Part Code Description No.
ASPLB1160WW Base 360x1160mm 1
BSPLP360T End Panel 360x876mm 2
CSPLP1200TV2 Back Panel 876x1200mm 1
DLINPLDOOR Door 332x894mm 1
ESPLP1200TDR Door Panel 876x1200mm 1
FSPLB1156 Shelf 356x1156mm 1
GJLINER12090S Jute Liner 1
H60200400PAII45PT End Surround 60x20x400mm 2
I60201200PAII45PT Side Surround 60x20x1200mm 2
Linear Planter With Storage (LINPL12090S)
A B CD E
FG H I