Forever Redwood DIY Wood Gazebo User manual

360 Gazebos www.foreverredwood.com
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday
Assembly instructions for:
360 GAZEBOS

360 Gazebos www.foreverredwood.com
Quantity
Description
Drawing
Quantity will
vary
depending on
size
Front wall panels –
panels
Quantity will
vary
depending on
size
Rear wall window
Quantity will
vary
depending on
size
Left side & right side
2
Doors

360 Gazebos www.foreverredwood.com
Quantity
Description
6
Bolts 4” x 5/16”, washers & nuts
10
Bolts 6 ½” x 3/8”, washers & nuts
4
Bolts 3 ½” x 5/16”, washers & nuts
8
Bolts 4 ½” x 5/16”, washers & nuts
4
Bolts 8” x 3/8”, washers & nuts
100
Screws 3”x 8” SS
4
Angled Corner Panels
1
Door frame
6
Roof timbers
10
Roof panels
2
10
Rafters
10
Roof trim
1
Skylight
Quantity will
vary
depending on
size
Snow Load boards
8

360 Gazebos www.foreverredwood.com
2 bolts
2 bolts
Step 2:
Attach the timbers together to form the base of the roof with 4 bolts (3 ½”x 5/16”)
washers & nuts. (Match up the numbers to attach the two parts together). Tap the
bolt all the way into the wood to set it. Then add a washer and nut and lightly
tighten.
Door frame
When you finish the walls of the Gazebo should be as shown.
Step 1:
Attach corner panel to wall panel
with six deckscrews (3”X 8”).
(Match up the numbers to attach
the two parts together).
The parts that go together have the same numbers written next to the predrilled holes they attach to.
Align the parts with the numbers as shown for ease of reference.

360 Gazebos www.foreverredwood.com
Step 5:
Attach the corner rafters to
skylight with 4 bolts (8”x 3/8”)
washers & nuts. (Match up
the numbers to attach the
two parts together). Tap the
bolt all the way into the wood
to set it. Then add a washer
and nut and lightly tighten.
Step 4:
Attach the center rafters to
the skylight with 6 bolts (4”x
5/16”) washers & nuts.
(Match up the numbers to
attach the two parts
together). Tap the bolt all the
way into the wood to set it.
Then add a washer and nut
and lightly tighten.
Step 3:
Attach the rest of the base of
the roof with 8 bolts (4 ½”x
5/16”) washers & nuts. Take
the timbers from step 3 and
add the other roof timbers as
shown.(Match up the
numbers to attach the two
parts together). Tap the bolt
all the way into the wood to
set it. Then add a washer and
nut and lightly tighten.

360 Gazebos www.foreverredwood.com
Step 9:
Attach the Roof panel to the
rafters with six deckscrews
(3”x 8”). And repeat the
process with each panel roof
panel.
Step 8:
Attach the snow load board to the Rafters
with bolts (6 ½” and 4 ½”). Match up the
numbers to attach the two parts together.
Step 7:
Attach the roof to the top of the Walls with
30 deckscrews (3” x 8”) –approximately 3
per panel. (Match up the numbers to attach
the two parts together).
Step 6:
Attach the rafters to base
of the roof with 10 bolts
(6 ½”x 3/8”) washers &
nuts. (Match up the
numbers to attach the
two parts together). Tap
the bolt all the way into
the wood to set it. Then
add a washer and nut
and lightly tighten.

360 Gazebos www.foreverredwood.com
Step 11:
Attach the doors to the metal hardware installed in the door panels. Use
deckscrews (3” x 8”).
Step 10:
Attach the roof trim between each roof panel
with three deckscrews (3”x 8”). And repeat
the process for each space between the
installed roof panels and fill between gaps
with silicone.