Belson Outdoors R8HA-P User manual

2014-08-13 – Page 1
Model # R8HA-P Instructions Sheet
www.belson.com
TRADITIONAL RECTANGULAR ACCESSIBLE TABLE
Inspecttheshipmentfordamageandconducta thorough
inventorytodeterminethatallpartsandhardware are present and
verify that all tools needed for assembly are on hand.
We are not responsible for items discovered missing or
damaged after 72 hours from time of delivery!
Ifyouhavea questionregardinganythingcoveredinthis manual,
pleasecontactyoursales representative.
Itis veryimportanttousecarewhenassemblingandmoving
theequipment.Donotdragtheequipment across any surface.
This equipmentrequiresperiodiccleaningwitha spongeor
softclothanda solutionof milddetergent andwater. Youmay
alsouse a solutionof50/50bleach/waterif necessary. Donot
cleanwitha solvent or petroleum-based products.
Apressurewashermaybeusedforcleaning(follow
manufacturer’s recommendationsfornozzletypeand distance
from surface to avoid damaging nish).
You may use a hair dryer to smooth out the plastisol/PVC
coating if it becomes dented.
Furniture must not be used other
than for its intended purpose. It
should be inspected regularly for
loose, missing or broken hard-
ware and general instability.
Furniture that is damaged or
appears to be unstable must be
removed from service and
repaired or replaced. Repairs
must be made using only factory
authorized parts and methods.
Recommended Crew:
Minimum 2 People
Tools Required:
Cardboard from Packaging / Drop Cloth
Level
Ratchet with 1/2” Socket
1/2” Open-End or Box-End Wrench
Assembly Time (approximately):
1 hour
WARNING!
627 Amersale Drive
Naperville, IL 60563
Phone: [phone]
Fax: [phone]
[email protected]

TABLE TOP
QTY. 1
SEAT
QTY. 2
DIAGONAL BRACE
QTY. 2
“H” FRAME FOR
RECTANGLE TABLE
QTY. 2
2014-08-13 – Page 2
www.belson.com
BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED.
5/16”-18X1-1/2” GRADE 5 ZINC
HEX BOLT
QTY. 16
5/16” ZINC FLAT WASHER
QTY. 32
5/16” NYLON LOCK NUT
QTY. 16
5/16” BOLT GUARD
QTY. 16

2014-08-13 – Page 3
www.belson.com
STEP #1:
Please Note: Use caution throughout the assembly/placement of the table. Do not drag or slide any part of
the table across any surface. Lay table top upside down on the packaging material or a drop cloth on a smooth,
flat surface to avoid damaging/scratching the product.
STEP #3:
Attach diagonal braces as shown. Hand tighten hardware at this time.
STEP #2:
Fit the frame to the top as shown, and secure with hex bolt, two washers, nylon lock nut and bolt guard at each
connection. Hand tighten hardware at this time.
Please Note:
The L-Brackets
“open” toward
the table end
(see details to
the right).
NYLON
LOCK NUT
FLAT
WASHERS
HEX
BOLT
BOLT
GUARD
NYLON
LOCK NUT
FLAT
WASHERS
HEX BOLT
BOLT
GUARD
DIAGONAL BRACE
TO H-FRAME LEGS
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
DIAGONAL BRACE
TO TABLE TOP
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
H-FRAME TO TABLETOP
HARDWARE DETAIL
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
Table Top Center
Table Top End
BOLT
GUARD
BOLT
GUARD
NYLON
LOCK NUT
NYLON
LOCK NUT
FLAT
WASHERS
FLAT
WASHERS
HEX
BOLT
HEX
BOLT
L-Brackets

2014-10-08 – Page 4
Table tops will be approximately 30” above the ground.
Seats will be approximately 18” above the ground.
Dimensions shown may vary based on installation and manufacture.
www.belson.com
STEP #5:
Please Note: this is at least a two-person
operation. Carefully turn table right side up
and tighten all hardware in an alternating
pattern to keep the frames straight under the
tops and seats. Use a level to verify table
frame, top and seats are level and plumb.
Pick table up off ground and carry to desired
location, using caution not to drag table
across any surface.
STEP #4:
Fit the seats to the attachment brackets as shown, and secure each seat with hex bolt, two washers, nylon lock nut
and bolt guard at each connection. Hand tighten hardware at this time.
SEAT
TABLE TOP
NYLON
LOCK NUT
FLAT WASHERS HEX BOLT
BOLT GUARD
H-FRAME TO SEAT
1 - 5/16” X 1-1/2” HEX BOLT
2 - 5/16” FLAT WASHER
1 - 5/16” NYLON LOCK NUT
1 - 5/16” BOLT GUARD
60-1/4”
29-1/4” 71-1/4”
53-3/4”
95-1/4”
25-3/4”
30”
18”
25-3/4”
10-1/4”
2”