Forever Redwood THE BREEZY SMALL PAVILION User manual

ASSEMBLY INSTRUCTIONS FOR THE
THE BREEZY SMALL PAVILION
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
CONTENT OF BOXES
No.
1
2
3
4
5
6
7
8
Drawing
Description
Posts
Single Supports
Supports with
In-Between Blocking
Triangles
Main Knee Braces
Secondary Knee
Braces
Roof Panels
Roof Trims
Qty.
Will Vary
Will Vary
Will Vary
Will Vary
Will Vary
Will Vary
Will Vary
Will Vary

P| 2
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
CONTENT OF BOXES
No.
9
10
11
12
13
Drawing
Hurricane
Gale Wind
Standard
Description
Metal plaques
Steel Roof Panel
Ridge Cap
Boots
Anchor Bases
Qty.
Will Vary.
Will Vary.
Will Vary.
Will Vary.
Will Vary.
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 3
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
HARDWARE LIST
No.
A
B
C
D
E
F
G
Drawing
Description
1/2´´ X 3 1/2´´ Anchor Bolts
(To attach the anchor bases to the ground).
5/16'' X 3'' Lag Bolts
(To attach the posts to the anchor bases/ To attach the metal plates
to the supports).
3/8´´ X 6´´ Bolts
(To attach the single supports to the posts. / To attach the single
supports to the supports with in-between blocking. / To attach the
triangles to the posts. / To attach the knee braces to the supports and
triangles).
3´´ Deck screws
(To attach the triangles to the supports. / To attach the boots to the
posts. / To attach the trims to the triangles).
3/8´´ X 7´´ Bolts
(To attach the knee braces to the posts. /To attach the metal plates
to the central triangle/ To attach the roof panels to the perimeter
triangles).
3/8´´ X 9´´ Bolts
(To attach the roof panels to the central triangles. / To attach the
ceiling fan base).
2´´ Deck Screws with Neoprene Washer
(To attach the steel roof panels to the roof panels. / To attach the
ridge cap to the steel roof panels).

P| 4
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
No
1
2
3
4
5
6
7
8
9
10
11
12
13
DESCRIPTION
Posts
Single Supports
Supports with
In-Between Blocking
Triangles
Main Knee Braces
Secondary Knee Braces
Roof Panels
Roof Trims
Metal plates
Steel Roof Panel
Ridge Cap
Boots
Anchor Bases
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on
the parts sent.

P| 5
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
NOTE: In order to know where the post needs to be placed, check the numbers on them. If the post is not marked, then place the
single Supports on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet, only
place them on the ground to begin with”).
Step 1: Install the anchor bases (13). After that, set your post (1) in the saddle of the anchor bases (13). Drill a ø ¼´´ hole in the
post prior to anchoring to facilitate the ratcheting of the hardware. After that, use a 5/16´´ X 3´´ lag bolts (A) to attach each post
to its respective anchor bases (13).
Step 2: Attach the single supports (2) to the posts with 3/8´´´x 6´´ bolts (C). Each part has a series of numbers that indicate where
to attach the part with the corresponding number.
2
2
1
1
1
1
13
3/8´´ X 6´´ Bolts
5/16´´ X 3´´ Lag Bolts
13

P| 6
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 3: Put up the supports with in-between blocking (3), into the post notches as shown and attach to the posts with the single
support bolts. Each part has a series of numbers that indicate where to attach the part with the corresponding number.
Step 4: Attach the single supports to the supports with in-between blocking, use 3/8´´ X 6´´ bolts (C). The quantity of bolts
depends on the length of the supports.
3
3
3/8´´ X 6´´ Bolts

P| 7
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 5: Attach the triangles (4) to the posts with 3/8´´ x 6´´ bolts (C) and to the supports with 3´´ deck screws (D). Each part has
a series of numbers that indicate where to attach the part with the corresponding number.
.
Step 6: Attach the metal plaques (10) to the supports with in-between blocking with 5/16´´ x 3´´ Lag Bolt (C). Each part has a
series of numbers that indicate where to attach the part with the corresponding number.
4
4
3/8´´ X 6´´ Bolts
3´´ Deck screws
10
5/16´´ X 3´´ Lag Bolt
10

P| 8
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 7: Attach the central triangle (4) to the supports with 8´´ x 3´´ deck screws (E) and use 3/8´´ X 7´´ Bolt (F) to attach the
metal plaques to the central triangle. Each part has a series ofnumbers that indicate where to attach the part with the corresponding
number.
Step 8: Attach the main knee braces (5) to the supports with 3/8´´ x 6´´ Bolts (C) and to the posts with 3/8´´ x 7´´ bolts (E).Each
part has a series of numbers that indicate where to attach the part with the corresponding number.
3/8´´ X 6´´ Bolts
3/8´´ X 7´´ Bolts
5
5
5
5
10
10
3´´ Deck screws
3/8´´ X 7´´ Bolt
4

P| 9
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 9: Attach the secondary knee braces (6) to the triangles with 3/8´´ x 6´´ Bolts (C) and to the posts with 3/8´´ x 7´´ bolts (E).
Each part has a series of numbers that indicate where to attach the part with the corresponding number.
Step 10: Use 3´´ deck screws (D) to attach the central triangle (4) to the supports. Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
6
6
6
3/8´´ X 6´´ Bolts
3/8´´ X 7´´ Bolts
6
3´´ Deck screws
4

P| 10
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 11: Use 3/8´´ x 7´´ bolts (E) to attach the roof panels (7) to the perimeter triangles and 3/8´´ x 9´´ bolts (F) to attach the roof
panels (7) to the central triangle, as shown below. Each part has a series of numbers that indicate where to attach the part with
the corresponding number.
Step 12: Attach the trims (8)to the triangles with 3´´ deck screws (D).
3´´ Deck Screws
8
3/8´´ X 7´´ Bolts
3/8´´ X 9´´ Bolts
7
7

P| 11
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 13: Use 2´´ Wood Screw with Neoprene Washer (G) to attach the steel roof panels (10) to the roof panels. The overlapping
between these steel roof panels it will be approximately of 2´´. Each part has a series of numbers that indicate where to attach the
part with the corresponding number.
Step 14: Use 2´´ Wood Screw with Neoprene Washer to attach the ridge cap (18). Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
10
2´´ Wood Screw
Overlapping,
approximately
of 2’’.
11

P| 12
THE BREEZY SMALL PAVILION
www.ForeverRedwood.com
Step 15: Finally, attach the boots (12)to each post with 8´´ x 3´´ deck screws (C).
This completes the Pavilion Assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question,
don't hesitate to call us (866 332 2403) or email us. We are here to support you.
3´´ Deck Screws
12