Forever Redwood FAN SHAPED PERGOLA KIT User manual

ASSEMBLY INSTRUCTIONS FOR THE
FAN SHAPED PERGOLA KIT
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
CONTENT OF BOXES
No.
1
2
3
4
5
6
7
8
9
Drawing
c
Hurricane
Gale Wind
Standard
Description
Posts
Supports
In-Between Blockings
Rafters
Main Knee Braces
Secondary Knee Braces
Slats
Boots
Standard, Gale Wind or
Hurricane Anchors Bases.
If ordered.
Qty.
Will
Vary
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 2
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
HARDWARE LIST
No.
A
B
C
D
E
F
G
H
I
J
K
Drawing
Description
½´´ X 3 ½´´ Anchor Bolts
(To attach the anchor bases to the ground).
5/16´´ X 3´´ Lag Bolts
(To attach the anchor bases to the posts).
3/8´´ X 9 ½´´ Bolts
(To attach the supports to the posts. / To attach the
in-between blockings and the main knee braces to
the supports).
3/8´´ X 7 ½´´ Bolts
(To attach the supports together. / To attach the
perimeter rafters to the posts).
3/8´´ X 11´´ Bolts
(To attach the main knee braces to the corner posts).
3/8´´ X 14´´ Bolts
(To attach the main knee braces to the center posts).
3/8´´ X 10´´ Bolts
(To attach the secondary knee braces to the posts).
3/8´´ X 5´´ Bolts
(To attach the secondary knee braces to the rafters).
3´´ Deck Screws
(To attach rafters to the supports. / To attach the
slats to the rafters. / To attach the boots to the posts).
Washers
Nuts
Note: Dimensions of your hardware will vary depending on size.

P| 3
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
No.
.
1
2
3
4
5
6
7
8
9
DESCRIPTION
Posts
Supports
In-Between Blockings
Rafters
Main Knee Braces
Secondary Knee Braces
Slats
Boots
Anchor Bases
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 4
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
NOTE: In order to know where the post needs to be placed, check the numbers on them. If the post is not marked, then place the
single Supports on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet, only
place them on the ground to begin with”).
Step 1: Install the anchor bases (9) with ½´´ X 3 ½´´ anchor bolts (A). Please see the “How to anchor your pergola document”
for all details.
Step 2: Set your post (1) in the saddle of the anchor bases. Drill a ø ¼´´ hole in the post prior to anchoring to facilitate the
ratcheting of the hardware. After that, use 5/16´´ X 3´´ lag bolts (B) to attach each post to its respective anchor base.
9
9
9
9
5/16´´ X 3´´ Lag Bolts
1
1
1
1
All options of posts (No posts decorative trim, vertical posts decorative trim and horizontal posts decorative trim)
will be installed in the same way.

P| 5
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
Step 3: Attach the supports (2) to the posts with 3/8´´ X 9 ½´´ bolts (C). Each part has a series of numbers that indicate where to
attach the part with the corresponding number.
Step 4: Use 3/8´´ x 7 ½´´ bolts (D)to attach the supports (2) together. Each part has a series of numbers that indicate where to
attach the part with the corresponding number.
2
3/8´´ X 7 ½´´ Bolts
2
2
3/8´´ X 9 ½´´ Bolts
3/8´´ X 9 ½´´ Bolts
2
2
2

P| 6
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
Step 5: Attach the in-between blockings (3) to the supports with 3/8´´ X 9 ½´´ bolts (C). Each part has a series of numbers that
indicate where to attach the part with the corresponding number.
Step 6: Use 3/8´´ X 7 ½´´ bolts (D) to attach the perimeter rafters (4) to the posts. Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
3
3/8´´ X 9 ½´´ Bolts
3
4
4
3/8´´ X 7 ½´´ Bolts

P| 7
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
Step 7: Attach the main knee braces (5) to the supports with 3/8´´ x 9 ½´´ bolts (C). After that, attach the main knee braces to the
center posts with 3/8´´ x 14´´ bolts (F) and to the corner posts whit 3/8´´ x 11´´ bolts (E).Each part has a series of numbers that
indicate where to attach the part with the corresponding number.
Step 8: Use 3/8´´ x 5´´ bolts (H) to attach the secondary knee braces (6) to the perimeter rafters and 3/8´´ x 10 bolts (G) to attach
to the posts. Each part has a series of numbers that indicate where to attach the part with the corresponding number.
5
3/8´´ X 9 ½´´ Bolts
3/8´´ X 9 ½´´ Bolts
3/8´´ X 11´´ Bolts
3/8´´ X 14´´ Bolts
5
5
3/8´´ X 10´´ Bolts
3/8´´ X 5´´ Bolts
6
6

P| 8
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
Step 9: Attach the rafters (4) to the supports with 3´´ deck screws (I). Each part has a series of numbers that indicate where to
attach the part with the corresponding number.
2.3
Step 10: Use 3´´ deck screws (I) to attach the Slats (7) to the rafters. Each part has a series of numbers that indicate where to
attach the part with the corresponding number.
7
3´´ Deck Screws
3´´ Deck Screws
4
4
4
7

P| 9
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
Step 11: Finally, attach the boots (8) to the posts with 3´´ deck screws (I). Each part has a series of numbers that indicate where
to attach the part with the corresponding number.
3´´ Deck Screws
8
8
8
8
8

P| 10
FAN SHAPED PERGOLA KIT
www.ForeverRedwood.com
This completes the Pergola assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question,
don't hesitate to call us (866 332 2403) or email us. We are here to support you.