Foxfury Lighting Solutions RUGO 700-300 User manual

PRODUCT MANUAL
700-300
RUGO™

2
TABLE OF CONTENTS
INTRODUCTION
Reference Guide 3
Overview 4
Physical Characteristics 4
POWER PACK
Charging the Power Pack 5
Reassembling the Rugo™after Charging 6
Power Pack Life 6
Operational Modes 6
TRI-LENS™
Using the Tri-Lens™7
Removing the Tri-Lens™7
REMOVING/CHANGING MOUNTS
Removing the Standard Mount 8
Removing the ¼"-20 & Cold-Shoe Mount 8
MOUNTING TO DEVICES
GoPro®9
DSLR 9
Tripod/Puck Adaptor 9
MAINTENANCE
Replacing the Seal 10
Removing the Guard 10
WARNINGS/WARRANTY 4, 12–13
CARE/CLEANING 12
CONTACT FOXFURY 13

3
RUGO™REFERENCE GUIDE
FULL ASSEMBLY
DISASSEMBLED
POWER PACK
DISASSEMBLED
LIGHT HEAD
MOUNTS INCLUDED
TRI-LENS™
THUMBSCREWS
POWER/MODE
SWITCH
¼"-20 MOUNT
CHARGE
INDICATOR
GUARDS
POWER CONTACTS
USB
CHARGE
PORT
LOCKING
POST
LED CONTACT
CAVITY (2)
“O”-RING
ACCESS SCREW
LED MODULE
SCREW HOLE (4)
¼"–20 AND
COLD-SHOE MOUNT
THUMBSCREWS (2)
STANDARD MOUNT
WITH (2) KNOBS

4
WARNINGS
When used for extended periods of time the Rugo™will become HOT to the touch.
Do not stare into the LEDs for long periods of time or from a close range (less than
2 ft).
This product is designed as an auxiliary lighting tool to be used with photo, video,
and film.
DO NOT use the Rugo™as a primary light source for activities.
While using any FoxFury product, please operate at safe speeds.
Be sure to rinse the Rugo™with fresh water immediatley after use in the ocean or
a pool.
It is the responsibility of drone/UAV users to follow the FAA laws and regulations
and/or the laws and regulations applicable to the flight location.
OVERVIEW
The Rugo™is a compact and powerful LED Light which has the ability to be
mounted to the GoPro®, a DSLR, a drone, a tripod and many other devices.
Having four different intensities (70–700 Lumens) with three interchangeable
lens settings (Tri-Lens™), makes it a powerful tool for action sports as well as
photography and filming. A Charge Indicator and Quick Swap™Power Pack
makes the Rugo™, patents pending,one of a kind.
IMPORTANT!
Please fully charge the Power Pack before using the Rugo™for the first time.
PHYSICAL CHARACTERISTICS
Please read below before using your Rugo™ as it relays beneficial operating
and safety information.
RUGO™
DIMENSIONS 2.9 x 1.0 x 2.0 in (74 x 25 x 50 mm)
WEIGHT 5.6 oz (158g) with Power Pack and Light Head
2.6 oz (73g) Power Pack
!
!
!
!
!
!

5
CHARGING THE POWER PACK
1. Press and hold the Power Pack Release Lever located on the Light Head
portion of the Rugo™.
2. While maintaining pressure on the Power Pack Release Lever, pull the Light
Head and the Power Pack apart.
If unable to pull apart easily (due to resistance of the internal rubber
gasket), try moving the Power Pack back and forth while pulling apart.
NOTE: Once apart, be sure to keep both ends dry and away from
water, moisture and dust. While the Power Pack and Light Head are
separated, the unit DOES NOT maintain its waterproof rating.
3. Insert the provided Micro USB Cable into the Power Pack— respect the
orientation/alignment. Then, insert the opposite end, USB (Type A) into a
USB compatible power source or into the included AC/DC Adaptor.
(Input: 100V–240VAC 50/60 Hz, Output: 5V DC 1000mAH).
The Charge Indicator will be solid red while charging. Once fully
charged, it will turn green.
Charging time will be approximately 2.5 hours.
After the Power Pack is charged, disconnect it from USB Cable.
**PLEASE NOTE: The Rugo™in steps 1–3 is shown with no mounts and is
flipped to show the Power Pack Release Lever.
1
1
2
3
2
3

6
REASSEMBLING THE RUGO™AFTER CHARGING
1. Install the Power Pack to the Light Head—confirm position of alignment
posts to their respected cavities.
2. Push both halves together. A ‘click’ should be heard as they become
locked together.
Test the light to make sure that the Power Pack is properly connected
to the Light Head by pressing the Power/Mode Switch.
POWER PACK LIFE
MODE DURATION LUMENS
HIGH 1 hour 700
MEDIUM 1.5 hours 400
LOW 3.5 hours 200
DIM 6.75 hours 70
*Power Pack life may vary according to age and ambient conditions.
OPERATIONAL MODES
ON/DIM mode: Press the Power/Mode Switch once.
LOW mode: From DIM mode, press the Power/Mode Switch once.
MEDIUM mode: From LOW mode, press the Power/Mode Switch once.
HIGH mode: From MEDIUM mode, press and hold the Power/Mode
Switch once.
OFF: From ANY mode, press and hold the Power/Mode Switch for 2 sec.
LOW POWER INDICATOR: At a low level, the Charge Indicator will flash
for approximately 0.5–1.0 sec. It is suggested that you then charge or
replace the Power Pack with a fully charged one. If on a higher mode and
you need to continue using the light, it is suggested that you adjust the
mode to a lower setting.
NOTE: The light does not retain the mode in memory. Once you turn the light
ON, you will have to re-select the mode you desire.
1
2

7
USING THE TRI-LENS™
AREA
55°
BEAM DISTANCE: 30ft (10m)
USED FOR: Mid-range
FLOOD
120°
BEAM DISTANCE: 10ft (3m)
USED FOR: Close-up
SPOT
BEAM DISTANCE: 100ft (30m)
USED FOR: Distance
18°
The Rugo™Tri-Lens™has three (3) beam emission angles which can be used for
many different applications by simply sliding from left to right and vise-versa.
1. Push the Tri-Lens™to either the right or left side until it won’t go any
further. Use your fingers to slightly pull the Guards away from the unit,
while pushing the Tri-Lens™with your thumb. This will help the Tri-Lens™to
overcome the ridge, (located at the end of the Guard) and will allow it to
be easily released.
2. Once the Tri-Lens™overcomes the ridge, pull it free from the Light Head.
FOR RE-INSTALLATION: Line up the Tri-Lens™with the ridge. Then push it
back into position on the Light Head.
REMOVING THE TRI-LENS™
1
1
2
2

8
¼"-20 AND COLD-SHOE MOUNT
1. Start with the Rugo™positioned so that the Thumbscrews are on top.
2. Twist each Thumbscrew counter-clockwise until they become loose. They
should then be ready to pull out completely.
3. Once Thumbscrews are removed, the ¼"-20 or Cold-shoe mount can then
be disengaged from the Rugo™completely.
STANDARD MOUNT
1. Start with the Rugo™positioned so that the Thumbscrews are on top.
2. Twist each Thumbscrew counter-clockwise until they become loose. They
should then be ready to pull out completely.
3. Once Thumbscrews are removed, the Standard Mount can then be
disengaged from the Rugo™completely.
REMOVING/CHANGING MOUNTS
1
1
1
2
2
3
3
2 3
1 2 3

9
MOUNTING TO DEVICES
ACTION CAM
The Rugo™can be mounted to an Action Cam via the removable Standard
Mount. Line up the mounts on the Rugo™with the mounts on the Action Cam
and then tighten the Mount Knobs.
TRIPOD OR PUCK ADAPTOR
The Rugo™can be mounted to most tripods or to the Puck Adaptor
(purchased separately) via the provided ¼"-20 Mount. Twist the threaded
hole of the Rugo™¼"-20 Mount onto the screw of the tripod or Puck Adaptor.
Then, twist the Rugo™and Puck Adaptor until it is securely fastened.
CAMERA
The Rugo™can be mounted to a DSLR camera via the removable Cold-shoe
Mount. Simply slide the mount onto the camera flash attachment and twist the
Locking Ring until securely fastened.
NOTE: Orientation of Knobs should match as shown below.

10
1. Use a size T6 Star-Tip (TORX) driver or bit (not included) to take out the
screws on the top and bottom of the Rugo™.
2. Once screws are loose, remove them and then lift up on the Guard to
remove it.
3. Repeat steps 1–2 to remove the Guard on the opposite side of the Rugo™.
FOR RE-INSTALLATION, make sure to tighten the screws until they are snug.
MAINTENANCE
1. Separate the Power Pack from the Light Head (follow steps 1–2 in the
“Charging the Power Pack” section on page 5).
2. Using a #2 Phillips head screwdriver (not included) remove the screw from
the Light Head (reference “Disassembled Light Head” diagram on page 3).
3. The Retaining Tab and O-Ring can now be removed.
If the O-Ring does not fall out on its own when unscrewed, it may need
to be pulled out.
Examine the O-Ring for cracks. If cracks are found, a replacement will
be needed to ensure the Rugo™waterproof rating.
FOR RE-INSTALLATION, follow the above listed steps in reverse order.
NOTE: The O-Ring can be lubricated with a non-silicone based grease.
1
1
1
2
2
3
3
2 3
O-RING
RETAINING TAB
1 2 3
REPLACING THE O-RING (P/N 51-112)
REMOVING THE GUARDS (P/N 51-905)

11
NOTES

12
PRODUCT DURABILITY
PRODUCT NAME: Rugo™
MODEL NUMBER: 700-300
ADAPTOR INPUT: AC 100-240V,
50/60 Hz
CARE/CLEANING
Your FoxFury product is a professional
tool. Regular maintenance and care of
your light will maximize performance for
you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that
both the Light Head and Power Pack
are reassembled securely before
washing. When done, pat dry with a
damp cloth.
AVAILABLE ACCESSORIES
Puck Adaptor, P/N 85-045
Tripo-Scope® M1, P/N 650-100
Rugo Quick Swap®Power Pack
P/N N50-200
Rugo Quick Swap®Power Pack
with Strobe, P/N N50-220
Rugo Standard Mount
P/N N50-132
Rugo ¼"-20 and Cold Shoe Mount
P/N N50-133
Handlebar/Drone Mount
P/N 85-026
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
When used for extended periods of
time the Rugo™will become HOT
to the touch. Please use care when
operating.
Lights are strong enough to cause
damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should
be operated at speeds safe
enough to maneuver around
surrounding obstacles.
Do not use under the influence
of drugs or alcohol.
LIMITED LIFETIME
WARRANTY
FoxFury, LLC (“FoxFury”) warrants
this product to be free from defects
in material for a lifetime of use except
for batteries, LEDs, abuse, and normal
wear. We will repair or replace this
product should we determine it to
be defective. This limited lifetime
warranty excludes rechargeable
batteries, chargers, switches, and
electronics, which have a 2-year
warranty with proof of purchase.
WARRANTY AND OTHER
INFORMATION
IPX7
20 M 3 M

13
This limited lifetime warranty is
given only to the original end user of
the accompanying product. If you
purchased a product from someone
other than an authorized FoxFury
reseller/distributor or if the product
was used, (including but not limited
to demo models, show models or
refurbished product by someone
other than FoxFury) prior to your
purchase, you are not the Original
Purchaser and the product that you
purchased is not covered by this
warranty. This limited warranty is
VOID if this Product has been altered
or modified in any way (including but
not limited to attempted warranty
repair without authorization from
Foxfury and/or alteration/removal
of the serial number). To expedite
warranty concerns, we encourage
the end user to register their FoxFury
Product at www.foxfury.com/pages/
warranty-registration.
THIS IS THE ONLY WARRANTY,
EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARE
EXPRESSLY DISCLAIMED EXCEPT
WHERE SUCH LIMITATION IS
PROHIBITED BY LAW.
You may have other specific legal
rights which vary by jurisdiction. Go
to www.foxfury.com/pages/warranty
for a complete copy of the warranty.
Retain your receipt for proof of
purchase.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts.
Products are assembled in either
FoxFury’s controlled plant in Asia or
the USA, under strict quality control.

FOXFURY.COM 10/2018