Foxfury Lighting Solutions Taker B70 User manual

PRODUCT MANUAL
480-600 | 480-670
TAKERTAKER B70

TABLE OF CONTENTS
INTRODUCTION
Taker B70 Reference Guide 3
Physical Characteristics & Warnings 4
BATTERIES
Battery Installation and Replacement 5
Battery Life 6
OPERATION
Operational Modes 6
FEATURES
Ambidextrous Light Activation 7
Pressure Switch 7
Individual LED Rows 8
Dual Settings 8
WARRANTY 9
CONTACT FOXFURY 10

3
TAKER B70 REFERENCE GUIDE
LIGHT HEAD
(FRONT)
HANDLE
(BACK SIDE)
LEDs (6)
POWER/MODE
SWITCH (2)
BATTERY
CAP (2) GRIP
HANDLE
(FRONT SIDE)
PRESSURE
SWITCH
PORT
GRIP
KILL SWITCH

4
PHYSICAL CHARACTERISTICS
Please read below before using the Taker B70 as it relays beneficial operating
and safety information.
LIGHT HEAD
DIMENSIONS (WxH) 8.1 x 1.1 x 3.0 in (206 x 28 x 76 mm)
WEIGHT 11.64 oz (330 g)
HANDLE
DIMENSIONS (WxH) 9.8 x 3.5 x 3.3 in (250 x 88 x 83 mm)
WEIGHT 10.75 oz (304.8 g)
WARNINGS
Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft/ 0.6 m).
FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.
Do NOT attempt to charge the batteries by using the Pressure Switch
Port.
INCLUDED
Taker B70 Shield Light Head
Taker B70 Handle & Square Pressure Switch

5
BATTERY INSTALLATION AND REPLACEMENT
1. Twist the Battery Cap (at both ends of the handle) in a counter-clockwise
direction to remove them.
2. Insert three (3) batteries (with the negative end first) into either side of the
handle (respect appropriate polarity when installing).
If installing six (6) batteries (doubling battery life), then repeat step 2
one more time on the opposite side of the handle.
3. Re-install the Battery Cap(s) by twisting in a clockwise direction (make
sure the Battery Cap(s) are tightly sealed).
Test the light’s performance and function by activating the Power/
Mode Switch (located under the Grip).
BATTERIES
The Taker B70 uses three (3) or six (6) CR123 batteries. As long as there
are at least three (3) installed, the light will function.
Using three (3) CR123 batteries decreases the battery life by half, but
does not effect the light intensity.
Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.
1
2
1
2
3
3

6
OPERATIONAL MODES
BATTERY LIFE
MODE BATTERY LIFE LUMENS
MOMENTARY 2 hrs 1,200
CONTINUOUS ON 2 hrs 1,200
TURBO-STROBE™ 4 hrs 1,200
*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.
For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the light will operate continuously. When the user
removes pressure from the Switch, the light will turn OFF.
For CONTINUOUS ON mode: Press the Power/Mode Switch two (2)
times in rapid succession. The light will remain ON.
For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in
rapid succession.
For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.
The Taker B70 has a KILL SWITCH located on the right side of the
Handle behind the Power/Mode Switch. This mechanism is a safety
precaution to make sure the light does not turn on when not intended to.
NOTE: The light does not retain the mode in memory. Once you turn the light
ON, you will have to re-select the mode you desire.

7
FEATURES
AMBIDEXTROUS LIGHT ACTIVATION
The Taker B70 includes two (2) Power/Mode Switches on both the left and
right sides of the Handle. This allows users to toggle between modes using
either hand.
PRESSURE SWITCH (INCLUDED)
The Taker B70 includes a Square Pressure Switch that allows the user to
place it anywhere on the shield. This makes it easier to access the Power/
Mode Switch. The Pressure Switch can easily be attached to the shield or
Handle via Velcro®or glue.
POWER/MODE
SWITCH
POWER/MODE
SWITCH
PRESSURE
SWITCH PORT
SQUARE PRESSURE SWITCH
HANDLE
(BACK SIDE)
HANDLE
(FRONT SIDE)
KILL SWITCH
CABLE TIE
HOLE (4)

8
FEATURES (CONT’D)
INDIVIDUAL LED ROWS
The LEDs of the Taker B70 operate on separate circuits, allowing a single row
of LEDs to continue functioning if the other row is damaged.
DUAL SETTINGS
The Taker B70 includes two mode settings: the ON/OFF SETTING and the
TACTICAL SETTING. The ON/OFF SETTING simply allows the Light Head to
turn ON and OFF. The TACTICAL SETTING allows you to choose from three
(3) different Operational Modes: Momentary, Continuous On, and
Turbo-Strobe™. The Taker B70 is shipped in the TACTICAL SETTING.
To change from the TACTICAL SETTING to the ON/OFF SETTING:
With the light turned OFF, press the Power/Mode Switch twice in rapid
succession and hold for 10 seconds. The light should begin to flash. Once
it begins flashing, it is now in the ON/OFF SETTING.
To change from the ON/OFF SETTING to the TACTICAL SETTING:
With the light turned OFF, press and hold the Power/Mode Switch for 10
seconds. The light should begin to go through a slow Turbo-Strobe™ cycle
and then turn OFF. It is now in the TACTICAL SETTING.

9
PRODUCT DURABILITY
CARE/CLEANING
Your FoxFury product is a professional
tool. Regular maintenance and care of
your light will maximize performance for
you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that all
parts are reassembled securely before
washing. When done, pat dry with a
damp cloth.
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
Lights are strong enough to cause
damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft/ 0.6m).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should be
operated at speeds safe enough
to maneuver around surrounding
obstacles.
Do not use under the influence
of drugs or alcohol.
WARRANTY AND OTHER
INFORMATION
LIMITED WARRANTY
FoxFury, LLC (“FoxFury”) warrants
to the purchaser of this product
(“Buyer”) that for a period of two
years following purchase, this product
will be free from defects in material
and workmanship and will function in
substantial compliance with FoxFury’s
written specifications for this product
as specified in the instruction manual
or on FoxFury’s website located at
www.FoxFury.com. Buyer’s exclusive
remedy shall, in any case, be limited,
at FoxFury’s election, to: A) repair or
replacement of the defective product;
or B) refund of the purchase price for
this product.
THE FOREGOING WARRANTY IS
THE ONLY WARRANTY MADE
BY FOXFURY WITH RESPECT TO
THIS PRODUCT. TO THE EXTENT
ALLOWED BY APPLICABLE LAW,
THERE ARE NO REPRESENTATIONS
OR WARRANTIES OF ANY KIND
BY THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE
CONDITION OR PERFORMANCE OF
THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE.
THIS LIMITED WARRANTY SHALL
NOT APPLY IF THIS PRODUCT IS
NOT STORED, HANDLED, INSTALLED
OR USED IN STRICT ACCORDANCE
WITH MANUFACTURER’S
SPECIFICATIONS AND INSTRUCTION
MANUALS, OR WHICH HAS BEEN
SUBJECT TO MISUSE, ALTERATION,
NEGLIGENCE OR ACCIDENT.
1. The damaged part or product must
be returned to FoxFury PRIOR TO
any repair or replacement. Shipping
costs are the responsibility of the
claimant.
2. You must obtain a return
authorization (RMA) number from
FoxFury prior to returning products.

10
FoxFury is not responsible for any
damage incurred while in transit.
3. Buyer will be required to
show proof of purchase—NO
EXCEPTIONS.
4. Any modifications to light, cable or
battery pack automatically voids all
warranties on this product.
All warranty inquiries should be directed
to FoxFury’s Customer Service
Department at [e-mail]
to handle all warranty/repair-related
inquiries.
TO THE EXTENT ALLOWED BY
APPLICABLE LAW: (A) IN NO EVENT,
WHETHER DUE TO BREACH OF
WARRANTY HEREUNDER OR ANY
OTHER CAUSE WHATSOEVER,
SHALL FOXFURY BE LIABLE FOR
OR OBLIGATED IN ANY MANNER TO
PAY CONSEQUENTIAL, INCIDENTAL
OR INDIRECT DAMAGES, INCLUDING,
BUT NOT LIMITED TO, LOSS OF
PROFITS, COST OF SUBSTITUTE
PRODUCTS AND PERSONAL
INJURY OR PROPERTY DAMAGE,
WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY
OTHER THEORY OF LAW, AND
(B) FOXFURY’S ONLY DUTIES IN
CONNECTION WITH THE SALE
OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY
SET FORTH HEREIN. TO THE
EXTENT THAT THIS LIMITED
WARRANTY IS INCONSISTENT WITH
APPLICABLE LAW, THIS STATEMENT
SHALL BE DEEMED MODIFIED
TO BE CONSISTENT WITH SUCH
APPLICABLE LAW.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts. Products
are assembled in either FoxFury’s
controlled plant in Asia or the USA,
under strict quality control.

11
NOTES

FOXFURY.COM 11/2020