FRANCO BELGE Bourgogne User manual

Description of the appliance
Installation instructions
Operating instructions
Spare parts
Warranty certificate
Document n° 1091-6 ~ 25/10/2005
Bourgogne
Oil burning stove
Ref. 174 10 56
(NF EN 1)
Technical manual
to be saved
by the user
for future reference
STAUB FONDERIE
SARL ith the capital of 6 359 540 &
Head Office Address
2, rue Saint Gilles
68230 TURCKHEIM
RCS Colmar
SIREN 444 881 953
Address
Administration and manufacturing
BP 73
59660 MERVILLE (FRANCE)
Telephone : [phone]
Fax : [phone]
Subject to modifications.

2Technical manual “1091”
“Bourgogne” ref. : 174 10 56
CONTENTS
Description of the unit ...................................P.3
Description ................P.3
Package..................P.3
Optional equipment ...........P.3
Specifications. . . . . . . . . . . . . . . P. 3
Operating principle . . . . . . . . . . . . P. 4
Installation instructions...................................P.5
Warning to the user ...........P.5
Location of the unit............P.5
Chimney .................P.5
Smoke exit ................P.6
Chimney connector............P.6
Levelling .................P.6
External / remote tank ..........P.6
Pre-utilization check . . . . . . . . . . . P. 7
Oil flows adjustment . . . . . . . . . . . P. 7
Mounting the tray. . . . . . . . . . . . . P. 8
Chimney draught . . . . . . . . . . . . . P. 8
Maintenance of the Chimney . . . . . . P. 8
Fitting the “visioflamme” (optional) . . . P. 8
Instructions for user.....................................P.9
Fuel ....................P.9
Lighting ..................P.9
Operating procedure ...........P.9
Shutting down ..............P.9
Recommendations . . . . . . . . . . . P. 10
Maintenance of the stove. . . . . . . . P. 10
Removing the burner . . . . . . . . . . P. 10
Trouble shooting . . . . . . . . . . . . P. 11
Spare parts .........................................P.12
FRANCO BELGE congratulates you on your choice.
FRANCO BELGE, which has been granted the ISO 9001 certification, guarantees the
quality of its appliances and is committed to meet its customers’ needs.
FRANCO BELGE, which can boast a 75-year experience in the industry of heating devices,
uses state-of-the-art technologies
to design and manufacture its whole range of products.
This document contains instructions on how to install your appliance and make full use of
its functions, both for your comfort and safety.

This appliance is an oil-fired stove.
WARNING
An incorrectly installed oil-fired stove can cause serious accidents.
This appliance should only be installed by competent personnel.
1. Description of the unit
1.1. Description
Flued oil stove with vaporizing burner. (Norm EN1)
1.2. Package
•1 package : Stove
1.3. Optional equipment
•1 package : Visioflamme (mirrors : P 174 10 53)
•1 package : Glow-plug ignitor
•1 package : Coals kit (FC 0802)
1.4. Specifications
Model ................. 1741056
Nominal Heat Output .......kW 10
Oil consumption
at maximum speed .......litre/hr 1,27
at minimum speed .......litre/hr 0,25
Chimney draft required
at maximum speed .........Pa 17
at minimum speed .........Pa 8
Weight ................kg 118
Technical manual “1091” 3
“Bourgogne” ref. : 174 10 56 Description of the unit
5 4 4
5 8 5
Ø 120/125
3 8 5
4 0 2 6 2 0
7 6 0
5 6 2
7 0 2
Figure 1 - Dimensions in mm

1.5. Operating principle
Heat is mainly diffused by radiation, through the window
and body of the appliance.
The speed control is obtained by control the oil flow into
the burner.
The stove is fitted with a vaporizing burner
Furnace oil is fed to the burner floor where is it ignited
by means of a firestarter (or with an optional electrical
igniter).
The heat produced by this flame brings the burner
temperature to the required level to vaporize the oil.
Oil will only burn as a vapor not a liquid.
Combustive air enters the burner through the air way
holes.
In the centre of the burner is the catalyser, which aids
the good combustion.
When the stove is in operation, the catalyser glows red.
The stove should not be used without the catalyser.
On the feed-line there is a de-scaling lever.
The de-scaling lever can be operated to keep the inlet
pipe clear of carbon build-up.
The stove float regulator contains a filter to trap
impurities. A safety lever controls oil flow. A float in the
chamber raises the oil level available to the burner.
Oil can only enter the float chamber when the safety
lever is depressed.
The float regulator is also controlled by a control knob
which turns from off to high setting.
A draft regulator ensures a constant air intake to the
burner regardless of external factors.
4Technical manual “1091”
“Bourgogne” ref. : 174 10 56 Description of the unit
1
22 b
2 c
3
4
5
2 a
Figure 2 - Burner
1- Air holes
2- Catalyser
2a : Upper ring
2b : Catalyser top
2c : Catalyser body
3- Burner pot
4- Automatic ignition
(optional)
5- De-scaling lever
Figure 3 - Float regulator
A- Control knob
B- Safety lever.
C- Main float
D- Safety float
E- Oil level regulator
F- Thermostat control
G- Filter
A
F
B
E
G
C
D

2. Installation instructions
2.1. Warning to the user
An incorrectly installed heating appliance can
cause serious accidents (chimney fires, burning of
plastic insulation materials, in partition walls, etc.).
The insulation of both the appliance and the
exhaust gas pipe has to be reinforced and built as
well as possible according to the norm to make sure of
the equipment operational reliability.
The installation must be carried out according to local
building regulations.
It is the installer’s responsibility to conform to local
building standards and requirements with regard to
installation.
The manufacturer’s responsibility shall be limited to the
supply of the equipment.
A remote acting fire valve must be fitted on the oil
supply line.
Flexible oil lines must not be used to make connections
between oil supply line and oil regulator valve.
2.2. Location of the unit
Ventilation :
For satisfactory operation with a natural draught,
check that sufficient air for combustion is available in
the room.
In houses equipped with mechanical ventilation, an
outside air intake of minimum 50 cm2must be installed.
Position of the unit :
For new installations, select a central position within the
house, to provide a good heat distribution around the
building.
The heat distribution towards the other rooms will be
made through the communicating doors. These rooms
must be in negative pressure or must include ventilation
gratings.
Floor and walls :
Make sure there are not combustible or covered with
combustible material.
Otherwise it must be necessary to install a
non-combustible protection.
Position the unit to comply with the minimum
clearances to combustible material (figure 4).
2.3. Chimney
The chimney must comply with Current Building
Regulations. If in doubt, consult your Dealer or local
Building Inspector.
The flue must be in good condition and must provide
sufficient draught. (refer to technical details page 3).
The flue must be suitable for the installation of fuel
burning appliances ; otherwise it must necessary to
install a tubing.
The flue must be clean. It should be swept to remove
soot and dislodge tar deposits.
The flue must be well insulated, water and air tight. A
chimney with a cold internal surface can prevent a good
chimney draught and condensation will occur.
The flue must be watertight.
The chimney must have a constant cross section.
The flue must not be shared with any other appliance.
The chimney must be at least 4.5 m (15 ft) high.
In case of a flat roof or when the roof gradient is lower
than 15°, the stack must be 1,2 m (4 feet) high at least.
The capping must not restrain the draught.
If the chimney has any downdraught tendency, due to
its position in relation to nearby obstacles, an
anti-downdraught cowl must be installed on the
chimney or the chimney height must be increased.
If the chimney draught is excessive or irregular, a
draught stabilizer (barometric damper) must be
installed to the connector pipe.
It must be distant from any combustible material (walls,
cross members)
It must permit an easy sweeping.
Technical manual “1091” 5
“Bourgogne” ref. : 174 10 56 Installation instructions
300
300
300
300
300
300
Figure 4 - Minimum clearances

2.4. Smoke exit
The stove is supplied with the flue collar at rear.
For a smoke exit on the top (fig. 6):.
-Remove the reflector and the internal baffle (fig. 11,
p. 8)
-Exchange the blanking plate 5with the flue collar 1,
ensuring that it is leaktight.
-Reinstall the internal baffle and the reflector.
-Close the exit position with the iron plate supplied 3.
2.5. Chimney connector
The connection to flue must be carried out according to
local building regulations.
The appliance must be installed as close as possible to
the chimney.
The connector pipe must be approved for installation
with combustion products (either 24 ga. Black painted
or blued steel or 316 grade 20 ga. Stainless steel or
1 mm vitreous enamelled steel).
Pipe diameter must not be less than the appliance
spigot diameter.
If there is no other solution, the reduction can not be
more than one diameter lower than the flue spigot and
be situated as distant as possible from the flue
connection of the appliance.
The join between the connection pipe and the
stovepipe, and the flue, must be leak tight.
The connection pipe and any draught stabiliser must
have access for cleaning.
2.6. Levelling
Four adjusting bolts with caps are supplied and which
have been placed in the burner for packing purposes
only.
-Fit the screws and caps (rep 6, fig. 5) to the bottom of
the stove legs.
-Put the stove on the oil drip tray (rep. 7, fig. 5).
-Place the level on the burner (fig. 7) and adjust the
bolts until the burner has reached a level position.
2.7. External / remote tank
Figure 8
6Technical manual “1091”
“Bourgogne” ref. : 174 10 56 Installation instructions
1
2
3
4
5
6
7
8
Figure 5 - Cross-section of the appliance
1- Flue collar
2- Blanking plate
3- Flue baffle
4- Flue baffle
5- Burner
6- Control screws for
appliance levelling
7- Oil drip tray
8- Clamp
1
2
3
4
5
6
2
Figure 6 - Smoke exit on the top
1- Flue collar
2- Sealing rope
3- Sealing plate
4- Clamp
5- Blanking plate
6- Back panel
Figure 7 - Burner level check

A barometric fuel tank should not be positioned where it
will be in the direct rays of the sun or adjacent to a
source of intense heat.
If the tank is more than 8 ft (2,5 m) higher than the stove
a pressure reducer must be installed on the oil line
(max. working pressure : 300 mbar).
If the tank is lower than the stove a lift pump will have to
be utilized.
2.8. Pre-utilization check
-Check that the glass is not damaged.
-Check that the door closes correctly.
-Check that all removable parts are correctly installed.
(flue baffle, reflector, etc.)
-Check that the seals of the smoke-line are in good
condition.
-Check that the seals of the feed-line are in good
condition.
Light the appliance by referring to the operating
instructions.
2.9. Oil flows adjustment
The float regulator has been adjusted at the factory and
should not need further adjustment.
The eventual re-fit must be realized by a qualified
engineer.
If the burner does not work correctly, check possible
causes before readjusting the settings :
-Chimney draught
-Fresh air inlet
-Oil supply.
Minimum speed (rep. 2, fig. 9)
Set the regulating knob on minimum speed (rep. 2,
fig. 13, page 9) and let the burner run for a few minutes.
The flame must completely cover the bottom of the
burner and the catalyser body must be glowing red hot.
If the flame is too small, the stove will soot up quickly ;
increase the flame by turning the setting screw (rep. 2)
clockwise.
If the flame is too high, reduce the flame by turning the
setting screw (rep. 2) counter clockwise.
Maximum speed (rep. 3, fig. 9)
Set the regulating knob on maximum speed and let the
burner run for a few minutes. The flame must be shaped
like a cone and reach the upper part of the door.
If the flame is too low, increase the flame by turning the
setting screw (rep. 3) counter clockwise.
If the flame is too high, reduce the flame by turning the
setting screw (rep. 3) clockwise.
Please note - Very important : The adjustments of the
float regulator are very sensitive. The high and the low
setting screws must never be turned more than a 1/4 of
a turn at a time in any direction from their initial setting.
When making any adjustments, allow 3 to 5 minutes
between adjustments to allow burner to stabilize to
previous adjustment before proceeding, if necessary.
Technical manual “1091” 7
“Bourgogne” ref. : 174 10 56 Installation instructions
Figure 8
Gravity oil supply
Pumped oil supply
1- Max. 2,5 m
2- Min. 0,25 m
3- Tank
4- Filter
5- Suction pomp with
reserve and filter
6- Pipe 3/8 in. O.D.
1
2
3
Figure 9 - Adjustment devices
1- Adjustment of the draught regulator
2- Adjustment screw for low setting
3- Adjustment screw for high setting
12
3
4
5
6
3
6
1
2

2.10. Mounting the tray
Figure 10
To avoid damage to the ash tray during transport, it has
been disconnected and stored behind the main door of
the oil stove. To reinstall the ash tray to the front of the
oil stove, tilt the tray at a 45° angle, centre onto tab ‘A’
and lower into place.
2.11. Chimney draught
The reading of the draught must be done once the unit
is hot (minimum 30 minutes of use).
Refer to the specifications (p. 3) for minimum draught
requirement.
The eventual re-fit must be realized by a qualified
engineer.
The adjustment of the draught will be made with the
barometric damper (rep. 1, fig. 9) located at the back of
the stove.
2.12. Maintenance of the Chimney
Chimney condition should be checked at least once per
year.
If the appliance is regularly used, the chimney should
be swept several times per year, together with the
stovepipe connection section.
-First remove the flue baffle (figure 11).
2.13. Fitting the “visioflamme” (optional)
Figure 12
-Slide each glass piece so that it fits into the upper and
lower channels of the reflector.
-Use pliers to pinch the ends of the channels to prevent
glass from falling out.
8Technical manual “1091”
“Bourgogne” ref. : 174 10 56 Installation instructions
A
Figure 10 - Mounting the tray
Figure 11 - Removing the flue baffle
Figure 12 - Fitting the “visioflamme”

3. Instructions for user
The manufacturer will not be responsible for damages
on parts of the appliance due to the use of prohibited
fuel or due to an alteration of the appliance or its
installation.
3.1. Fuel
Your stove is fitted with a specific float regulator for a
specific oil.
The fuel oil must be free from any dirt and water, which
could disturb the stove in operation.
When filling the tank, the appliance should not be in
operation to preserve the burner feed line from choking.
3.2. Lighting
Figure 13
Don’t light the appliance when it is hot. Wait until the
burner is completely cool before repeating the lighting
procedure.
-Be sure the control knob is to “0" (2a).
-Turn on oil supply,
-Push down gently on the safety lever (rep. 3). This will
allow the oil to flow into the float regulator.
-Open the front door, and remove the catalyser (rep. 2,
fig. 2, p. 4) from burner. Make sure the inside of the pot
is clean thoroughly, and there is no oil accumulation.
-Place 2 tablespoons of methylated spirit or gelled
alcohol in the bottom of the pot.
-Light the starter gel or methylated spirit with a
fireplace match or long butane lighter.
-Place the catalyser back into the burner, being sure it
is centred in the burner. Shut the main door.
Allow the burner to heat approximately 30 to 45 sec.
Turn dial to “1" position (2b).
Allow 10 to 15 minutes for oil fire and draught to
stabilize. The catalyser (or the ring) should glow red
before adjusting the control knob to a higher setting.
At the first lighting, the fire must be progressively
increased to allow the various parts to expand normally
and to dry up.
When the fire is lit for the first time, the appliance may
give off fumes from the new paint. This is normal but
ensure the room is well ventilated during the first few
hours operation.
3.3. Operating procedure
Allow 10 to 15 minutes after lighting to adjust the control
knob to a higher setting, usually setting (2c, fig. 13).
When increasing the heat output, move the control knob
only 1 number at a time, allowing 5 minutes between
moves for the flame to re-adjust to new setting.
If the burner stops during operating, immediately turn
off the control knob to position “0" (2a, fig. 13) and wait
until the burner is completely cool before repeating the
lighting procedure.
3.4. Shutting down
-Set dial to the “0" (2a, fig. 13) position.
-Raise the safety lever (rep. 3, fig. 13) of the regulator.
-Allow the flame to burn out completely before opening
the door.
Technical manual “1091” 9
“Bourgogne” ref. : 174 10 56 Instructions for user
1
2
= > ?
3
4
5
Figure 13 - Operating devices
1- Opening/closing the
main door
2- Regulation knob.
2a : Shutting down
2b : Lighting
2c : Normal speed
3- Safety lever.
4-Access to regulator’s
filter
5- De-scaling lever.

3.5. Recommendations
The adjustment of the stove has been made at the
factory and checked by your installer.
In case of trouble shooting, do the usual maintenance
operations.
If problem persists call your installer.
This room heater is a high heat producing appliance
and may cause severe burns if touched on the glass
front door, or on top directly over the burner - KEEP
CHILDREN AWAY.
CAUTION : Never light the burner if there is any amount
of oil in pot. Clean out oil before lighting.
Too much oil in pot may cause a racing : a very high
flame generating vibrations.
In case of racing :
Turn off oil supply.
Set dial to the “0" position until fire has decreased to
proper burn rate.
Do not overfire. If the unit or chimney connector starts to
glow you are overfiring.
3.6. Maintenance of the stove
•Every week : operate the de-scaling lever. Pull the
rod, then push the rod in rotating 360 degrees two or
three times (CAUTION : The rod is HOT).
•Every 3 or 4 months : Clean the burner completely.
-Remove and brush off the parts of the catalyser, using
a soft bristle brush.
-Loosen any carbon soot from the burner with a putty
knife, and vacuum clean. Ensure that the small air
holes are free of carbon.
•At least once a year / End of heating season : Clean
or replace the oil filters, the oil supply line and to
change the joint of the de-scaling lever (rep. A, fig. 15,
code 142889) by a professional installer.
To clean the filter of the float regulator :
-Set the regulation knob in closed position “0".
-Turn off the tankvalve or the valve of the oil supply line.
-Raise the safety lever of the float regulator.
-Place a small container (or a small rag) under the
regulator filter opening in order to collect the oil
contained in the regulator.
-Remove the filter cover plate located under the
regulator (rep. 4, fig. 13, p. 9) with a screwdriver,
-Remove the tubular filter from the regulator. Clean it
with oil using a soft brush, never a wire-brush.
-Replace the filter in the regulator, install the cover
plate and secure with the screw.
•Use a soft clean cloth to wipe the front glass when the
unit is running at a low burning rate. DO NOT CLEAN
GLASS WHEN HOT.
•When the main door (or the cover) is opened for
cleaning, the flame will be disturb, and turn to a yellow
flame. Clean quickly, but gently. Close the door, the
flame will return to a normal burning position.
•Clean all the enamelled panels of the stove with a dry
or slightly damp soft cloth.
3.7. Removing the burner
-Disconnect the feed line from the de-scaler nut,
unscrew the burner fixing nuts (figure 14).
When replacing the burner, tighten the nuts evenly and
connect the pipe so as to be airtight.
10 Technical manual “1091”
“Bourgogne” ref. : 174 10 56 Instructions for user
Figure 14 - Removing the burner
)
Figure 15 - The joint of the de-scaling lever

3.8. Trouble shooting
Situation Probable causes -Corrective action
Flames extinguish during
lighting.
Very cold chimney. No draught
established.
-Leave door ajar until fire has caught. Check air supply
in the room (page 5).
Fire extinguishes once
firestarter has burnt off.
Fuel tank is empty. -Fill tank.
Fuel valve is closed. -Open valve.
Main regulator float not engaging. -De-press the safety lever.
Control knob is set on “0". -Adjust control knob to (minimum speed).
Fire extinguishes during use. Fuel tank is empty. -Fill tank.
Insufficient fuel. -Check that the de-scaler, the float regulator filter and
burner pot are cleaned.
Flame is excessively large,
smoky and sooty.
Insufficient draught. þ-Call your installer.
Fuel adjustment made too
quickly.
-Return control knob to minimum speed ; wait for
normal combustion. (catalyser should glow red) ; wait 5
to 15 minutes between each adjustment.
Stove extinguishes and
re-lights itself.
Insufficient fuel. -Check that the de-scaler, the float regulator filter and
burner pot are cleaned.
Stove burns noisily. Burner contains excess fuel. -Adjust control knob to minimum speed. If problem
persists call your installer.
Fire smokes. Soot build up
noticed. Flame imbalance
Insufficient air supply. -Increase fresh air supply (open door, window ; add
make up air supply).
Downdraught or blockage in
chimney.
þ-Check chimney for soot build-up. Clean if necessary.
-Ensure chimney height is sufficient and cap is not
affected by any nearby obstructions.
-If problem persists call your installer.
Room is in negative pressure. -Increase fresh air supply (page 5).
Oil flow is too low on minimum
speed setting.
þ-Adjust low flow rate while control is set on “1", call your
installer.
Stove is not level. Flame
imbalance.
þ-Check level. Adjust if necessary.
Catalyser not centred. -Centre catalyser assembly.
The draught regulator is blocked
in open position.
þ-Unlock the draught regulator. Check the draught
regulator, adjustment and refit if necessary.
Coke build-up noticed. Insufficient fuel. þ-Check level.
Excessive draught þ-Check draught. If always excessive, a draught
stabilizer (barometric damper) must be installed to the
connector pipe.
Technical manual “1091” 11
“Bourgogne” ref. : 174 10 56 Instructions for user
þ: This sign means that you should asked
for a qualified engineer to do the work.

4. Spare parts
When ordering spare parts, specify the stove type and
serial number, including the colour index (on the
guarantee or identification plate), the name of the part
and the part number.
Example : Oil burning stove “Bourgogne” 174 10 56 Y,
Top plate 352124 EF
The identification plate is located on the back panel.
A= 174 10 56 L
B= 174 10 56 Y
12 Technical manual “1091”
“Bourgogne” ref. : 174 10 56 Spare parts
1 100956 Axle ...................A....B..01
2 905331 Complete burner ............A....B ..01
3 109552 Cap ...................A....B..04
4 110105 Barometric damper ...........A....B ..01
5 110405 Hinge pin ..........6x35 . . . A ....B ..02
6 119213 Descaler ................A....B..01
7 446310 Protection plate .............A....B ..01
8 134601 Pin .............2x20 . . . A ....B..02
9 134749 Pin .............4x20 . . . A ....B..01
10 181632 Adhesive rope .............A....B.1,32 m
11 142327 Gasket ...........d.16 . . . A ....B..01
12 149868 Knob ..................A....B..01
13 158541 Handle .................A....B..01
14 164205 Tightness nut ..............A....B..02
15 165139 Float regulator .............A....B..01
16 179605 Regulator shaft .............A....B ..01
17 181604 Ceramic rope ........10x4 . . . A ....B..1m
18 105006 Ceramic rope ........d.15...A....B.3,24 m
19 188828 Glass ..................A....B..01
20 205386 Back panel ...............A....B ..01
21 221200 66 Striking plate ..............A....B ..01
22 222565 Flue baffle................A....B ..01
23 236129 Sealing plate ..............A....B..01
24 236708 94 Bracket .................A....B ..01
25 239714 60 Regulator support ...........A....B..01
26 259015 Fixing plate ...............A....B ..04
27 260591 60 Heat shield ...............A....B..01
28 261811 60 Heat shield ...............A....B..01
29 262222 Shield ..................A....B..01
30 276231 Reflector ................A....B..01
31 300122 77 Leg ...................A .......04
31 300122 EF Leg ........................B..04
32 300472 77 Base...................A .......01
32 300472 EF Base ........................B..01
33 301515 66 Door lock ................A....B ..01
34 303301 76 Bearing .................A .......01
34 303301 EF Bearing ......................B..01
35 303718 77 Blanking plate..............A .......01
35 303718 EF Blanking plate ...................B ..01
36 303828 59 Flue collar ........Ø120/127.......B..01
36 303828 77 Flue collar ........Ø120/127 . A .......01
37 909401 Sliding door ...............A .......01
38 306273 79 Back wall ................A .......01
38 306273 EF Back wall .....................B..01
39 309857 77 Front plate ...............A .......01
39 309857 EF Front plate.....................B..01
40 309975 77 Main door ................A .......01
40 309975 EF Main door .....................B..01
41 310723 77 R. side panel ..............A .......01
41 310723 EF R. side panel ...................B..01
42 310821 77 L. side panel ..............A .......01
42 310821 EF L. side panel ...................B ..01
43 312625 Burner support .............A....B..01
44 321903 Rim ...................A....B..01
45 325304 79 Reducing plate .............A .......02
45 325304 EF Reducing plate ..................B..02
46 327801 Clamp ..................A....B..01
N° Code Description ........Type . . . A ....B..Qty
47 327901 77 Tray ...................A .......01
47 327901 EF Tray ........................B ..01
48 352124 77 Top plate ................A .......01
48 352124 EF Top plate .....................B..01
49 182756 Feed line regulator-burner .......A....B..01
50 198205 Catalyser ring..............A....B..01
51 194401 Catalyser cover .............A....B ..01
52 194402 Catalyser body .............A....B..01
53 905332 Burner..................A....B..01
54 332200 60 Oil drip tray ...............A....B..01
55 988869 Complete door ..................B..01
55 988871 Complete door .............A .......01
56 199309 Mirror glass (optional) . 1x(260x20) . A ....B..39
57 199204 Regulator filter .............A....B ..01
58 104708 Plug ...................A....B..01
59 109718 Chain ..................A....B..01
60 124412 Strut ...................A....B..04
61 161025 Touch-up paint .............A .......01
62 209913 Heat shield ...............A....B..01
63 142881 Gasket .................A....B..04
N° Code Description ........Type . . . A ....B..Qty

Technical manual “1091” 13
“Bourgogne” ref. : 174 10 56 Spare parts
1
5
2 5
5 7
8
1 2
1 4
1 6
2 0
2 4
4 2
1 7
1 8
3 5
4 8
2 2
4
3 6
3 0
4 1
1
3
2 7
3 1
3 2
4 3
1 3
3 3
5
9
1 0
1 8
5
4 0
2
6
1 1
2 1
3 9
4 4
4 9
5 0
5 3
5 1
4 7
2 8
3 8
4 5
3 4
3 7
4 6
4 5
5 5
7
5 4
5 9
5 8
5 2
2 9
5 5
2
3
3 1
3 1
3
3 1
3
1 4
1 9
2 6
5 6
2 3
1 7
6 0
6 1
6 2
6 3
Figure 16 - Spare parts view

§Guarantee certificate §
§Legal guarantee
The specifications, dimensions and information shown
on our documents are provided for information purposes
only and under no circumstances are binding upon the
vendor.
With the aim of constantly improving our equipment, all
modifications considered as necessary by our
departments may be made without notice.
The provisions of the present guarantee certificate are
not excluding or limiting the owner of the equipment’s
rights, concerning the legal guarantee regarding faults or
hidden vices which applies in all circumstances, in the
conditions detailed in articles 1641and following of the
civil code, and in the country in which the equipment was
purchased.
§Contractual guarantee
Our equipment is guaranteed against faults and hidden
vices subject to the following conditions:
1) Installation and adjustment of the device by a professional
installer.
2) Observance of the instructions provided in our technical
documents and our installation/adjustment instructions.
3) The installation, use and maintenance of the device carried
out in conformity with the applicable standards and
legislation, and with the indications provided in the technical
instructions accompanying the device.
This guarantee covers the replacement, in our factory, of
parts recognised as being defective from the outset by
our “Guarantee Inspection” Department. Carriage and
labour is at the user’s cost. Moreover, if the repair or
replacement of parts covered by the guarantee is found
to be too costly vis-à-vis the price of the appliance, the
decision to replace or repair the appliance will be taken
by the vendor.
Our guarantee is for 2 (two) years for all appliances, with
the exception of closed combustion fireplace and inserts
for which our guarantee is 5 (five) years excluding the
following:
1) Indicator lights, fuses, electrical elements and fans.
2) Parts subject to wear or in contact with high temperatures
namely: soles and burner grills, bottom plates baffles, ash
pans, paintwork and surface treatments for decorative
parts. Also excluded from this guarantee are seals and
windows.
3) Any damage which may result from the use of the appliance
with a fuel other than that stipulated in our instructions.
4) Damage occurring to parts caused by elements outside the
appliance (down draught, storm damage, damp, abnormal
pressure or vacuum, heat shocks, etc.).
5) Damage to electrical parts caused by plugging in and using
the appliance on a mains system, the voltage of which
(measured at the entrance to the appliance) is 10% above
or below the nominal voltage of 220 V.
§Exclusion of liability
In the case of a product manufactured at the client’s
request, under no circumstances may we, as a
subcontractor, be considered liable vis-a-vis the client or
third parties for defects arising from the installation or a
design fault with the item in question.
*Name and address of the installer : _____________________________
______________________________________________
(Telephone : _______________________________________
*Name and address of the customer : _____________________________
______________________________________________
Date of installation : __ __ / __ __ /__ __ __ __
Model of the appliance : q174 10 56
Color : qYqL
Serial number : ___ ___ ___ ___ ___ ___
• This certificate has to be completed and kept carefully.
In case of claims, send a copy of this to :
STAUB Fonderie, BP 73, 59660 MERVILLE, FRANCE.